Search Results

In this paper, responses from a vehicle's suspension, chassis and body, are used to demonstrate a methodology to optimize physical test results. It is well known that there is a variability effect due to an increase of wheel unsprung mass (due to loads measurement fixturing), tire pressure, speed, etc. This paper quantifies loading variability due to Wheel Force Transducer (WFT) unsprung mass by using a rainflow cycle counting domain. Also, presents a proving ground-to-test correlation study and the data reduction techniques that are used in road simulation test development to identify the most nominal road load measurement. Fundamental technical information and analytical methodology useful in overall vehicle durability testing are discussed. Durability testing in a laboratory is designed to correlate fatigue damage rig to road. A Proving Ground (PG) loading history is often acquired by running an instrumented vehicle over one or more PG events with various drivers.

The design of occupant restraint systems in the automotive industry has shifted from an empirical approach to a computer aided analysis approach for many years now. Various finite element software programs have been applied in crash safety analysis, and multi-body dynamics codes have been successfully used where quick system response times were required. Most new vehicle programs are analyzed by the use of finite element tools that were used for previous program projects. Software that has specific occupant protection features may be coupled with these finite element tools, or new vehicle programs may be developed from scratch by using one tool that does all, i.e. a tool where the multi-body dynamics are integrated into the finite element method. Both these approaches will be elaborated as valid tools for occupant protection analysis. At first, the coupling between the finite element crash program LS-DYNA and the F.E.

Based on the results of “An Evaluation of the Mechanical Properties of Wheel Force Sensors and their Impact on to the Data Collected During Different Driving Manoeuvres” Herrmann et al. (SAE Paper 05M-254) a second, detailed investigation has been started to acquire additional information. In this previous investigation, it has been found out, that a difference in mass can be clearly identified in the signals. The current paper summarizes the results of a detailed investigation, which has been performed at DaimlerChrysler Stress Lab in Auburn Hills, with a fully equipped vehicle - a set of 2/4 Wheel Force Sensors plus several acceleration sensors as well. Through careful research and testing it is expected that the differences in the dynamic behavior can be specified with better accuracy than in the previous study.

Hot Isostatic Pressing (HIP) has been routinely used to densify castings for aerospace and medical applications for over 30 years. While HIP is widely known to improve the toughness and fatigue life of castings through the healing of internal porosity, it has been perceived as too expensive for most cast aluminum alloys for automotive applications. Recent developments suggest that the cost effectiveness of certain special HIP processes should be revisited due to reductions in process cost and improvements in throughput. This paper will evaluate the Densal® II process applied to a front aluminum steering knuckle. Two casting processes representing differing levels of relative cost and quality were evaluated. The first was Alcoa's VRC/PRC process, a metal mold process with bottom fill, evacuation before fill and pressurization after fill. This is considered to be a premium quality, but higher cost casting process that is already qualified for this application.

Traditionally, high-strength low-alloy (HSLA) steel is used for automotive vehicle weight reduction in the North American automotive industry. Dual phase (DP) high strength steel has gained great attention because it provides a combination of high strength and good formability. The main advantage of DP steel is the high ratio of tensile strength to yield strength, which provides more flexibility in stamping and higher energy absorption in a component crush event. This study compares the performances of DP and HSLA steel grades in stamping processes and component crush events, as shown in a typical automotive unibody inner rail. Simulation results show that DP steel offers more uniform strain distribution, improved formability, and better crush performance than conventional HSLA steel.

The staircase fatigue testing method is a recognized method for determining the fatigue limit of powertrain components. The purpose of this paper is to improve upon existing standards by adding common practices that will ensure a higher degree of statistical accuracy in the data. This includes specifying appropriate sample sizes, stress increments and initial load conditions, as well as making suggestions for appropriate methods of analyzing the data. Two methods (Dixon and Mood method and probit analysis method) are selected and compared in terms of relative percent difference on four parameters (mean, standard deviation, B10 fatigue strength and B50 fatigue strength). The staircase data are obtained by simulations from normal and lognormal fatigue limit distributions.

Sheet metal stamping involves a system of complex tribological (friction, lubrication, and wear), heat transfer, and material strain interactions. Accurate coefficient of friction, strain, and lubrication regime data is required to allow proper modeling of the various sheet stamping processes. In addition, non-intrusive means of monitoring the coefficient of friction in production stamping operations would be of assistance for efficiently maintaining proper stamping quality and to indicate when adjustments to the various stamping parameters, including maintenance, would be advantageous. One of the key sub-systems of the sheet metal stamping process is the draw bead. This paper presents an investigation of the tribology of the draw bead using a Draw Bead Simulator (DBS) Machine and automotive zinc-coated sheet steels. The investigation and findings include: 1) A new, non-intrusive method of measuring the surface temperature of the sheet steel as it passes through the draw bead.

At the initial accessory drive system design stage, a model was created using commercial CAE software to predict the dynamic response of the pulleys, tensioner motion and pulley slip. In a typical 6 cylinder automotive accessory drive systems, the first system torsional mode is near the engine idle speed. The combination of these two events could generate numerous undesirable noise and vibration effects in the system. Data acquisition on a firing engine with a powertrain dynamometer confirmed the computer model's results. Correlations are then developed and established based on results between the firing engine to the CAE model to increase confidence in the generated model. Further system optimization through design modifications are used to tune the system to minimize the overall system dynamics.

During the initial vehicle design phase and as the first prototypes are built, extensive on-board instrumentation and data acquisition is required at the proving grounds (PG). The data is used for various types of testing and analysis. During this phase of development very few parts and assembly components are available for physical test. The objective is to develop a component test for the truck box. This test can be run without suspension parts during the early stages of the vehicle development. A further objective is to correlate the test to FEA models and actual Proving Ground full vehicle test results.

Novel testing procedures and analytical methodologies to assess the performance of hybrid electric vehicle batteries have been developed. Tests include both characterization and cycle life and/or calendar life, and have been designed for both Power Assist and Dual Mode applications. Analytical procedures include a battery scaling methodology, the calculation of pulse resistance, pulse power, available energy, and differential capacity, and the modeling of calendar- and cycle-life data. Representative performance data and examples of the application of the analytical methodologies including resistance growth, power fade, and cycle- and calendar-life modeling for hybrid electric vehicle batteries are presented.

The recent trends of increasing driveline torque and use of traction control devices call for increasingly higher durability capacity from driveline components. Bench and vehicle durability tests are often used to validate designs, but they are not cost-effective and take months to complete. Traditional finite element analysis (FEA) procedures have been used effectively in the re-design of driveline components to reduce stress, and occasionally, to predict fatigue life. But in the case of certain rotating components, such as the Axle Differential Case, where the component sees large stress/strain fluctuations within the course of one complete rotation, even under constant input torque, historical fatigue analysis (when conducted) yields very conservative results. The axle differential case tends to be one of the weakest links in the rear axle assembly. Therefore, there is a crucial need for analytical methods to more accurately predict fatigue life to reduce testing time and cost.

The effect of forming strains on the fatigue behavior of an automotive mild steel, interstitial free steel, was studied after being prestrained by balanced biaxial stretch and plane strain. In the long life region, higher than 5×105 reversals, prestrain improves fatigue resistance. In the short life region, prestrain reduces fatigue resistance. At even shorter fatigue lives, the detrimental effect of prestrain diminishes. For plane strains, the fatigue behavior is anisotropic. In the direction perpendicular to the major strain, the steel exhibits much better fatigue resistance than in the direction parallel to the major strain.

Durability of automotive structures is a primary engineering consideration that is required to be assessed at every design and development stage. Due to limitations of the analytical and experimental tools, the current practice in the automotive industry is to conduct a new data acquisition over a proving ground schedule whenever there are changes in the suspension parameters. This is a time-consuming and expensive operation. This paper provides guidelines for product teams to determine if a new vehicle data acquisition is needed when there are changes in vehicle parameters, and the corresponding effect on Road Test Simulator (RTS) drive file development. The application of this methodology to a truck with and without tuned suspension parameters is described in detail.

This paper describes a program of coastdown and wind tunnel tests conducted with the objective of establishing a correlation between the aerodynamic drag force measured at the Lockheed-Martin Low-Speed Wind Tunnel (LSWT) and that inferred from coastdown results on the test track. The result of this correlation establishes, in principle, the capability to project what the aerodynamic drag force inferred by a future coastdown test will be (for a future, as-yet unavailable property) based on a current database of wind tunnel results. The correlation is accompanied by a rigorous uncertainty analysis to assess the quality of the correlation and its supporting data.

Thixomolding (1) is a relatively new process in which the metallic slurry is injected into a die cavity tool at semi-solid or liquid temperatures to form near net-shape products from the solid feedstock. As part of on-going research into Thixomolding technology, this study continues the work of a previous study, that concentrated on magnesium alloys AZ91D and AM60B. The test samples were made with high, low and zero percent fraction solid. The test results of the thixomolded samples of the various percent fraction solid are compared to conventional high pressure die casting samples and there is a discussion of the why the Thixomolding process produces superior properties. In addition, a comprehensive corrosion resistance study was completed utilizing uncoated corrosion plates in an salt spray environment (ASTM B117).

Detail parts are approved during several different phases of the prototype build cycle. There is much pressure at all stages to meet strategic body quality targets. Parts stamped for assembly must meet a process capability requirement of Cpk>1.33. For final PSO (process sign off), as called out in the PPAP (Production Part Approval Process) manual, the requirement can be increased to meeting a Cpk>1.67. During the 2000 Neon part approval process, the PPAP requirements provided the guideline necessary for consistent buy-offs. However, on some critical parts the Cpk requirement made part approvals difficult to accomplish. Occasionally this caused resources to be focused in the wrong place. This paper will discuss how a requirement of Cpk>1.33 can make part approvals more difficult to achieve and change the entire application of a tolerance.