Search Results

This paper discusses an approach to detecting small leaks in an automobile's evaporative emissions systems that is a technique based upon ideal gas laws. It does this by monitoring pressure in the system while the vehicle's engine is off. This low cost solution can be easily implemented on General Motors vehicles using existing components. The topics covered in this paper include details on the background of the problem and the technique, the underlying thermodynamics of the technique, a description of the algorithm, testing and data collection considerations.

The impact of ultra thinwall catalysts on TIER2 emission performance, packaging and total system cost was evaluated. The primary focus was to compare ultra-thinwall and thinwall cell configurations (400/3, 400/4, 600/2, 600/3, 600/3 hex, 900/2, and 1200/2) with a baseline 600/4 at constant substrate volume, washcoat and PGM loading. Other areas investigated included the evaluation of decreasing catalyst volume while maintaining constant or increased mass transfer capabilities while holding washcoat and PGM loadings constant. The emissions impact of varying washcoat and PGM loading was measured on specific substrates, including a comparison of square to hex cell. Backpressure for each configuration was calculated with the Corning substrate pressure drop modeling tool. Converters were rapid aged on dynamometers reflecting approximately a 50,000 mile aged performance. Emission testing was completed using the FTP test cycle.

The control of NOx emissions is the greatest technical challenge in meeting future emission regulations for diesel engines. In this work, a modal analysis was performed for developing an engine control strategy to take advantage of fuel properties to minimize engine-out NOx emissions. This work focused on the use of EGR to reduce NOx while counteracting anticipated PM increases by using oxygenated fuels. A DaimlerChrysler OM611 CIDI engine for light-duty vehicles was controlled with a SwRI Rapid Prototyping Electronic Control System. Engine mapping consisted of sweeping parameters of greatest NOx impact, starting with OEM injection timing (including pilot injection) and EGR. The engine control strategy consisted of increased EGR and simultaneous modulation of both main and pilot injection timing to minimize NOx and PM emission indexes with constraints based on the impact of the modulation on BSFC, Smoke, Boost and BSHC.

A compact, lightweight compression-ignition engine designed for high fuel economy and low emissions was developed by ISUZU for the GM PNGV vehicle. This engine was the key component in the selected parallel hybrid vehicle powertrain for the 80 mpg fuel economy target. The base hardware was derived from a 1.7 Liter, 4-cylinder engine, and a three-cylinder version was created for the PNGV application. To achieve the required high efficiency, the engine used lightweight components thus minimizing weight and friction. To reduce exhaust emissions, electromechanical actuators were used for EGR, intake throttle, and turbocharger. Through careful application of these devices and combustion development, stringent engine out exhaust emission targets were also met.

The newly developed Duramax 6600 V8 Diesel engine has incorporated a lot of the latest technologies to achieve better fuel economy and lower exhaust emissions. It will provide the GMC Sierra and Chevrolet Silverado with a Diesel engine to satisfy a multitude of major customer requirements such as higher output, lower fuel consumption, comfortable V8 sound, high reliability and good driveability. An optimized combustion system coupled with a four-valve per cylinder configuration, high pressure common rail fuel injection system, new design combustion chamber and valve covered orifice (VCO) nozzle enables to meet 1998 U. S. Environmental Protection Agency (EPA) emission standards for heavy-duty diesel engines without exhaust gas recirculation (EGR) and aftertreatment.

A new concept of highly efficient and sulfur tolerant NOx reduction catalyst for diesel engines has been demonstrated. This catalyst has a double-layer construction and is composed of Pt and Rh as the precious metals, oxygen storage materials and some other catalytic components. Periodic lean/rich operation similar to the Lean NOx Trap catalyst was found to improve the highly efficient NOx reduction activity in a laboratory reactor test. As a result, this catalyst has the feature of high NOx reduction in a temperature window from 15°C to 35°C, and of high oxidation activity even in a lower temperature condition for HC and CO. Sulfur poisoning characteristics were also evaluated in a laboratory reactor test. The results showed that the proper desulfation procedure with a relatively low temperature environment enabled the stored sulfur to be reomved, and to maintain the NOx reduction efficiency for asignificantly long time period.