Search Results

Clutches are commonly utilised in passenger type and off-road heavy-duty vehicles to disconnect the engine from the driveline and other parasitic loads. In off-road heavy-duty vehicles, along with fuel efficiency start-up functionality at extended ambient conditions, such as low temperature and intake absolute pressure are crucial. Off-road vehicle manufacturers can overcome the parasitic loads in these conditions by oversizing the engine. Caterpillar Inc. as the pioneer in off-road technology has developed a novel clutch design to allow for engine downsizing while vehicle’s performance is not affected. The tribological behaviour of the clutch will be crucial to start engagement promptly and reach the maximum clutch capacity in the shortest possible time and smoothest way in terms of dynamics. A multi-body dynamics model of the clutch system is developed in MSC ADAMS. The flywheel is introducing the same speed and torque as the engine (represents the engine input to the clutch).

Smaller locomotives often use mechanical transmissions instead of diesel-electric drive systems typically used in larger locomotives. This paper discusses how Model Based Design was used to develop the complete drive train control system for a 24 ton sugar cane locomotive. A complete MATLAB Simulink machine model was built to fully test and verify the shift control logic, traction control, vehicle speed limiting, and braking control for this locomotive application before it was commissioned. The model included the engine, torque converter, planetary transmission, drive line, and steel on steel driving surface. Simulation was used to debug all control code and test and refine control strategies so that the initial field commissioning in remote Australia was executed very quickly with minimal engineering support required.

Lubricating oil affects the performance of friction materials in transmission, steering and brake systems. The TO-2 Test measured friction retention characteristics of lubricating oils used with sintered bronze friction discs. This paper introduces a new friction performance test for drive train lubricants that will be used to support Caterpillar's new transmission and drive train fluid requirements, TO-4, which measures static and dynamic friction, wear, and energy capacity for six friction materials, and replaces the TO-2 test. The new test device to be introduced is an oil cooled, single-faced clutch in the Link Engineering Co. M1158 Oil/Friction Test Machine.

This paper presents a virtual analysis method for pressure spike estimation and optimization of hydraulic system architecture for off-highway applications with hydraulically actuated clutch. This pressure spike leads to a very high torque spike in driveline components during clutch pop-up conditions in puddling operations. These torque spikes lead to potential failure of driveline components i.e., gear, shaft, bearing and torsional damper during sudden engagement events. To assess the hydraulic system performance during clutch pop-up cornering conditions is very challenging and leads to compromise on operator safety in the paddy field. It is essential to develop a simulation methodology in a virtual environment to understand the system behavior during clutch pop-up condition and impact of various hydraulic system parameters. This paper describes a Model Based System Design (MBSD) approach for understanding hydraulic system pressure spike phenomenon and dynamic response.

Public concern and increasing regulations surrounding environmental issues, such as CO₂ emissions, are making it important for car makers to improve the fuel efficiency of the vehicles they manufacture and sell. A wide array of transmission technologies are being employed towards this end including, but not limited to, 6, 7, and 8 speeds stepped automatic transmissions, dual clutch transmissions (DCT) and continuously variable transmissions (CVT). The number of passenger cars equipped with CVTs has been increasing and push belt CVT types (b-CVT) are widely used. Since engine torque is transferred to the wheels via friction between the steel elements of the belt and the steel pulleys in a b-CVT, having a high metal on metal friction is required. As the CVT fluid is a key part of the CVT system, using a special CVT Fluid (CVTF) is critical in order to provide and maintain the required high metal-on-metal friction performance.

Chrysler began a limited development program directed toward a new automatic transmission fluid (ATF) early in 1989 and launched a full time effort in 1994. The development process for the new ATF involved a significant level of bench testing and eventually vehicle tests to evaluate the durability and shift quality of the ATF. The bench tests included those that pertain to oxidation and shear stability, anti-wear, frictional properties and torque converter shudder. Vehicle tests were primarily extended durability in both internal vehicle fleets and at external taxi sites. The mileage accumulated in this phase of the development program exceeded two million miles, all with no fluid drains out to 100,000 miles. Additionally, shift feel tests were conducted in Chrysler vehicles to verify compliance to targets. This paper summarizes the tests and results that lead to the development of the new Chrysler fill-for-life automatic transmission fluid.