Search Results

Adding oxygenates to diesel fuel has shown the potential for reducing particulate (PM) emissions in the exhaust. The objective of this study was to select the most promising oxygenate compounds as blending components in diesel fuel for advanced engine testing. A fuel matrix was designed to consider the effect of molecular structure and boiling point on the ability of oxygenates to reduce engine-out exhaust emissions from a modern diesel engine. Nine test fuels including a low-sulfur (∼1 ppm), low-aromatic hydrocracked base fuel and 8 oxygenate-base fuel blends were utilized. All oxygenated fuels were formulated to contain 7% wt. of oxygen. A DaimlerChrysler OM611 CIDI engine for light-duty vehicles was controlled with a SwRI Rapid Prototyping Electronic Control System. The base fuel was evaluated in four speed-load modes and oxygenated blends only in one mode. Each operating mode and fuel combination was run in triplicate.

A zero-dimensional cycle simulation model coupled with a chemical equilibrium model and a two-zone combustion model has been extended to predict nitric oxide formation and emissions from spark-ignited, lean-burn natural gas engines. It is demonstrated that using the extended Zeldovich mechanism alone, the NOx emissions from an 8.1-liter, 6-cylinder, natural gas engine were significantly under predicted. However, by combining the predicted NOx formation from both the extended Zeldovich thermal NO and the Fenimore prompt NO mechanisms, the NOx emissions were predicted with fair accuracy over a range of engine powers and lean-burn equivalence ratios. The effect of injection timing on NOx emissions was under predicted. Humidity effects on NOx formation were slightly under predicted in another engine, a 6.8-liter, 6-cylinder, natural gas engine. Engine power was well predicted in both engines, which is a prerequisite to accurate NOx predictions.

A 1993 Ford Taurus Flexible Fuel Vehicle (FFV) designed to operate on gasoline or methanol has been modified to run on Ed85 (85 vol.% denatured ethanol, 15 vol.% gasoline) and has demonstrated the ability to meet California's Ultra-Low Emissions Vehicle (ULEV) standards. The vehicle maintains the excellent driveability with potentially increased performance and similar efficiency to the baseline vehicle. Using standard twin OEM catalysts, FTP-75 emissions were 0.085 g/mi NOx, 0.88 g/mi CO, and 0.039 g/mi reactivity-adjusted NMOG. Using close-coupled catalysts upstream of the OEM catalysts, FTP-75 emissions were 0.031 g/mi NOx, 0.297 g/mi CO, and 0.015 g/mi reactivity-adjusted NMOG. The catalysts were aged to about 4,000 miles of equivalent use. These emissions compare with ULEV standards of 0.2 g/mi NOx, 1.7 g/mi CO, and 0.04 g/mi NMOG at 50,000 miles of use.

A recent study of engine sensitivity revealed that spark plugs used in conventional spark-ignited gasoline-fueled engines do not always fire in the intended fashion. Rather than firing to the ground strap during each ignition event, the arc frequently travels to the “rim” or “shell” of the spark plug. This behavior is termed rim-fire and although observed by other researchers in industry, its effects on engine performance are not widely reported. This paper addresses some of the quantitative effects of rim-fire on engine performance. Combustion data were recorded for various repeat conditions on a Ford 1.8L Zetec engine. The first set of engine tests used four, new, conventional, automotive spark plugs. The second set of engine tests used four modified spark plugs that induced 100% rim-fire when the ground strap was permanently removed. The study focused on part- and full-load engine performance, EGR tolerance, and step-transient characteristics.

A menu-driven, PC-based model, ALAMO_ENGINE, has been developed to predict the nitrogen oxides (NOx) reductions in direct-injected, diesel engines due to exhaust gas recirculation (EGR), emulsified fuels, manifold or in-cylinder water injection, fuel injection timing changes, humidity effects, and intake air temperature changes. The approach was to use a diesel engine cycle simulation with detailed gas composition calculations for the intake and exhaust gases (including EGR, water concentration, fuel-type effects, etc.), coupled with a code to calculate stoichiometric, adiabatic flame temperatures and expressions that correlate measured NOx emissions with the flame temperature. Execution times are less than 10 seconds on a 486-66 MHz PC.