Search Results

The tire is one of the most important parts, which influence the noise, vibration, and harshness of the passenger cars. It is well known that effect of rotation influences tire vibration characteristics, and earlier studies presented formulas of tire vibration behavior. However, there are no studies of tire vibration including lateral vibration on effect of rotation. In this paper, we present new formulas of tire vibration on effect of rotation using a three-dimensional flexible ring model. The model consists of the cylindrical ring represents the tread and the springs represent the sidewall stiffness. The equation of motion of lateral, longitudinal, and radial vibration on the tread are derived based on the assumption of inextensional deformation. Many of the associated numerical parameters are identified from experimental tests.

This paper describes a steady vibration of an engine supported by rubber and hydraulic mounts at a relatively low frequency range, assuming an engine is a rigid body. We identify dynamic characteristics of a hydraulic mount with respect to frequency and amplitude. The equation of motion is solved numerically by the Newton-Raphson method, treating the mount characteristics as functions of frequency and amplitude. The excitation test to simulate an engine shake and an idling vibration was performed using a mass block instead of an actual engine. During the engine shake, we observed that the amplitude dependency of hydraulic mounts strongly influences the vibration, while idling, we investigated rolling vibration especially for the case where the torque axis does not pass through the engine's center of gravity. The theoretical predictions agree closely with the experimental results in both engine shake and idling vibration tests.

Diesel Particulate filter (DPF) is installed as after treatment device of exhaust gas in diesel engine, and collects the Particulate Matter (PM). However, as the operation time of engine increases, PM is accumulated in the DPF, resulting in deterioration of PM collection efficiency and increasing in pressure loss. Therefore, Post injection has been attracted attention as DPF regeneration method for burning and removing PM in DPF. However, Post injection causes oil dilution when fuel is injected at the middle to late stage of expansion stroke. Oil dilution are concerned to deteriorate the sliding property of piston and the thermal efficiency. For this reason, it is necessary to elucidate the mechanism and the behavior that spray impinges lubricating oil film. Therefore, in this study, we aimed to construct model of Computational Fluid Dynamics (CFD) that predicts amount of oil dilution which is concern for post injection in diesel engine, with high accuracy.

To reduce tire/road noise, it is important to examine the noise generation mechanism. Noise generated by a rolling tire is mainly emitted from the tread block. However, it has recently been reported that smooth tires also generate noise recently. This paper remarks on a smooth tire vibration by rolling on the road. The vibration of a rolling smooth tire is mainly vibration excited from the road surface. It is difficult to measure the input from the road surface, so we measured the tire's vibration at the leading and trailing edges. Scan Laser Doppler Vibrometers were employed to measure the vibration of the tire tread.

Recently, the development stage of agricultural vehicles such as the tractor has focused on new demands to improve the cabin environment. Especially the ride comfort has become increasingly important. For this purpose, rubber bushes have been installed the tractor to reduce road vibration to the driver in the cabin. However, this device does not sufficiently suppress vibration. This paper presents a method of vibration reduction that installs a semi-active suspension in the lateral and vertical directions at the cabin mount position of the tractor. In numerical simulation, the tractor model installed with a semi-active suspension is superior in performance to the conventional tractor model.

Improvement of vehicle interior noise is desired in recent years in the modern world of the demand of low weight, good fuel economy and offering technical advantages strongly. The dynamic force transmission of rolling tires from the road surface to the spindles is a critical factor in vehicle interior noise. We focus on structure-borne noise transferred through the spindle. It is necessary for effort of the effective tire/road noise reduction to predict spindle force excited by tire/road contact. The major issues in predicting spindle forces are to clarify the distribution of road forces and how to input on the simulation model. Therefore, it is important that road forces are measured accurately on the rolling tire. First, the dynamic road forces on the rolling tire are measured by using the tri-axial force sensor directly. In efforts to reduce interior noise due to structure-borne noise, it is necessary to predict spindle forces excited by the tire/road contact.

This paper presents an analytical model for the prediction of piston secondary motion and the vibration due to piston slap. For the modeling of piston slap phenomenon, cylinder liner is modeled as a several spring-mass system that are connected by modal characteristics, and lubricant film between the piston and the cylinder is modeled as reaction force vectors which excite resonant mode of them. By comparing experimental results and analytical ones, the validity of the proposed model has been confirmed. The optimization of the piston skirt profile is also carried out with the analytical model, and it is confirmed that the round shape of the lower part of piston skirt is effective for the reduction of piston slap excitation.

Current simulation of Noise, Vibration and Harshness (NVH) using Computer Aided Engineering (CAE) often uses a large DOF and detailed finite element model along with improvement of CAE technology and computational performance. By using a detailed model, predictions of precise vibration characteristics become possible. However, the number of eigenmodes in the target frequency range increases and engineers require a lot of time to examine eigenmodes and establish countermeasures. In this paper, a practical method of efficient and effective analysis by classifying target eigenmodes into a small number of groups is proposed. The classification is executed based on the relation between the dynamic characteristics of the entire automotive body structure and substructures.

In an SI engine with direct injection of gasoline (DGI), many small droplets disperse in premixed gas in the cylinder. In a CI engine, diesel spray is injected a cylinder, thus, the situation at the spray periphery is almost the same as that of DGI SI engine. From the standpoint it is useful for understanding the combustion phenomena in both engines to experiment the combined combustion of premixed gas where many small droplets exist. This paper describes this kind of combustion and it seems to be able to apply the results to the simulation of combustion in these engines.

Dual mass flywheel (DMF) is a well-known isolation system for vehicle drivetrain. DMF has two typical elastic energy storage systems: long travel arc springs and in-series spring units (including two or more springs) and sliding shoes connected in series. DMF has such complex nonlinear characteristics as torque-dependent torsional stiffness and rotational speed-dependent hysteresis friction due to its dependency of centrifugal force that is applied to components and radial force of springs. Because of this complexity, sub-harmonic vibration (SHV) may occur under certain circumstances, such as under light-load and high-rotational conditions. In general, since SHV’s frequency is 1/2 or 1/3 of the engine’s combustion frequency and may cause human discomfort, DMF must be designed robust against such nonlinear vibration. In this paper to reduce the SHV occurrence and to show a more robust design indicator, the SHV causing the mechanism is researched by testing and 1D CAE modeling.

We have proposed the application of EGR gas dissolved fuel which might improve spray atomization through effervescent atomization instead of high injection pressure. In this paper, the purpose is to evaluate the influence of the application of CO2 gas dissolved fuel on the combustion characteristics and emissions inside the single cylinder, direct injection diesel engine. As a result, by use of the fuel, smoke was reduced by about 50 to 70%. The amount of NOx was reduced at IMEP=0.3 MPa, but it was increased at IMEP=0.9 MPa.

This paper describes the identification of a sound source model for diesel engines installed on agricultural machines by using Inverse-Numerical Acoustic (INA) analysis, and noise predictions using the sound source model identified by INA. INA is a method of identifying surface vibrations from surrounding sound pressures. This method can be applied to sound sources with complicated shapes like those in engines. Although many studies on INA have been conducted, these past studies have focused on improvements to the identified accuracy and prediction of noise in free sound field or hemi-free sound field. The authors accurately predicted the sound pressure levels of engine enclosures using a sound source model identified by INA and a boundary element method (BEM). However, we had not yet verified the effectiveness of this sound source model against enclosures that had sound absorbing materials and openings.

This paper describes the relationship between the rider's evaluation of feeling of pulse and the seat vibration of the cruiser-type motorcycle. A simulated running condition was created to measure the seat vibration and engine speed. Next, the seat vibration was reproduced on the hydrodynamic shaker. Finally, we examined the influence of which order of rotational speed effects evaluation of feeling of pulse in a forced vibration test. As a result, it is known that 0.5th and 1st orders of seat vibration contribute to evaluation of feeling of pulse near 1,500 to 2,000 rpm of engine rotation.

The purpose of this paper is to establish a method of predicting the noise and vibration of tractor cabins in the engine-idling state by using Statistical Energy Analysis (SEA). At first, an analytical model of a tractor cabin is constructed, and power flow equations are formulated for the tractor cabin. To solve these equations, SEA parameters are estimated experimentally and analytically. These parameters are the modal density, loss factor, coupling loss factor, and input power. With these parameters, the noise and vibration responses of the tractor cabin are calculated. Good agreements are found between the analytical and experimental data.

In this study, the air suspension is newly applied to the engine mounting layout for getting the significant vibration isolation effect. In this case, the genetic algorithm so called GA is also applied for the optimization of many parameters, calculations of stiffness matrix and inverse stiffness matrix to prevent the coupled vibration of lateral and rolling modes and to obtain the displacement of each mounting point. As a result, inexperienced engineers can easily obtain the optimum engine mounting layout in a minute. By the confirmation test of FEM, the engine lateral vibration level at 25Hz dropped below 1/10 and its effect was significant.

Some papers on the combustion in a diesel engine have been already presented to discuss the effect of the additive called ADOIL TAC. A bottom view DI diesel engine driven at 980rpm with no load was used in the experiment presented here, in order to make clear this effect. JIS second class light diesel fuel oil was injected through a hole nozzle at the normal test run. The additive was intermixed 0.01 vol. % in this fuel oil, in the experiments to compare with the normal combustion. The flame was taken by direct high-speed photography. Profiles of flame temperature and KL were detected on the film by image processing, applying the two-color method. Soot was visualized by high-speed laser shadowgraphy, and the heat release rate was calculated using the cylinder pressure diagram. Discussion on the effect of the additive on the combustion phenomena was made by using all the data.

Researches for automation of hydraulic excavators have been conducted for laborsaving, improved efficiency of operations and increased worker's safety improvement. Authors' final goal is to develop automatic digging system which can realize the high efficiency. Therefore, it is thought that appropriate digging control algorithm is important for the automation. For this goal, this paper shows a dynamics model of the backhoe excavator and simulations using such models. Detailed dynamic models are needed from the point of view of the control engineering. Authors evaluate effectiveness of automatic digging algorithm by simulation models. In this research, the linkage mechanism which contains the closed loops is modeled based on the Newton-Euler formulation, where motion equation is derived. Moreover, we apply a soil model for simulation, based on the two dimensional distinct element method (DEM), in order to reproduce reaction force from grounds.

The demand for quieter vehicle interiors increases year after year. The dynamic force transmission of rolling tires from the road surface to the spindles is a critical factor in vehicle interior noise. We investigated the dynamic force transmission of a rolling tire as it relates to reducing vehicle interior noise. A test with a tire rolling over a cleat was conducted in order to measure the road forces and the spindle forces. The transfer function of the rolling tire was identified from the experimental results by applying multi dimensional spectral analysis. In addition, Computer Aided Engineering (CAE) technology has advanced recently. This enables prediction of spindle forces early in the design stage. One of the most important issues in predicting spindle forces accurately is to clarify the distribution of road forces. This paper also describes the distribution of the dynamic road forces of the rolling tire.

This paper describes damping loss factor prediction in statistical energy analysis (SEA) for co-generation system (CGS) enclosures. To accurately predict vibration and noise by SEA, it is important to estimate parameters called the damping and coupling loss factors. In this study, the damping loss factors were estimated by the decay ratio method and a technique for calculating the modal damping ratio that uses a multi-degree of freedom curve fit. The calculated loss factor was applied to the vibration prediction of the co-generation system, and the influence of the internal loss factor calculation method on prediction accuracy was verified.

This paper describes new method for selecting optimal field points in Inverse-Numerical Acoustic analysis (INA), and its application to construction of a sound source model for diesel engines. INA identifies the surface vibration of a sound source by using acoustic transfer functions and actual sound pressures measured at field points located near the sound source. When measuring sound pressures with INA, it is necessary to determine the field point arrangement. Increased field points leads to longer test and analysis time. Therefore, guidelines for selecting the field point arrangement are needed to conduct INA efficiently. The authors focused on the standard deviations of distance between sound source elements and field points and proposed a new guideline for optimal field point selection in our past study. In that study, we verified the effectiveness of this guideline using a simple plate model.