Search Results

The development of systems and components for control of exterior noise has traditionally been done through an iterative process of on road testing. Frequently, road testing of vehicle modifications are delayed due to ambient environmental changes that prevent testing. Vehicle dynamometers used for powertrain development often had limited space preventing far field measurements. Recently, several European vehicle manufacturers constructed facilities that provided adequate space for simulation of the road test. This paper describes the first implementation of that technology in the U.S.. The facility is typical of those used world wide, but it is important to recognize some of the challenges to effective utilization of the technique to correlate this measurement to on road certification.

In order to engineer Squeak & Rattle (S&R) free vehicles it is essential to develop an objective measurement method to compare and correlate with customer satisfaction and subjective S&R assessments. Three methods for exciting S&Rs -type surfaces. Excitation methods evaluated were road tests over S&R surfaces, road simulators, and direct body excitation (DBE). The principle of DBE involves using electromagnetic shakers to induce controlled, road-measured vibration into the body, bypassing the tire patch and suspension. DBE is a promising technology for making objective measurements because it is extremely quiet (test equipment noise does not mask S&Rs), while meeting other project goals. While DBE is limited in exposing S&Rs caused by body twist and suspension noises, advantages include higher frequency energy owing to electro-dynamic shakers, continuous random excitation, lower capital cost, mobility, and safety.

DESCRIBED here is a 250-hp free-piston gasifier-turbine engine that has actually been installed in an automobile. A unique feature of this Hyprex engine is that it is a siamesed unit. The overall design has been selected, according to the author, to secure a compact, light-weight machine with improved thermal efficiency and with a reduction in general noise. Although the engine is still in the experimental stage, the author reports that analysis and results indicate it will be a serious contender for powering automotive vehicles.

This paper describes the application of Statistical Energy Analysis (SEA) and Experimental SEA (ESEA) to calculating the transmission of air-borne and structure-borne noise in a mid-sized sedan. SEA can be applied rapidly in the early stages of vehicle design where the degree of geometric detail is relatively low. It is well suited to the analysis of multiple paths of vibrational energy flow from multiple sources into the passenger compartment at mid to high frequencies. However, the application of SEA is made difficult by the geometry of the vehicle's subsystems and joints. Experience with current unibody vehicles leads to distinct modeling strategies for the various frequency ranges in which airborne or structure-borne noise predominates. The theory and application of ESEA to structure-borne noise is discussed. ESEA yields loss factors and input powers which are combined with an analytical SEA model to yield a single hybrid model.

The more noise and vibration improvements are incorporated into our vehicles, the more customers notice squeaks and rattles (S&R). Customers increasingly perceive S&R as a direct indicator of vehicle build quality and durability. The high profile nature of S&R has the automotive industry striving to develop the understanding and technology of how to improve the S&R performance in the vehicle. Squeaks and itches make up a significant amount of Squeak and Rattle complaints found in today's vehicles. Squeaks and itches are the result of stick slip behavior between two interacting surfaces. Squeak itch behavior is dependent upon a large number of parameters including but not limited to: the material itself, temperature, humidity, normal load, system compliance, part geometry, velocity, surface roughness, wear, contaminants, etc. This paper will describe the analysis of sound data and friction data and the relationship between them.

This paper discusses four general attributes which quantify the character of an impulsive sound event. These attributes include the time duration, amplitude and frequency content of the impulsive noise. A three dimensional plot relating time, frequency and amplitude have been developed for the presentation of the measured data. This format allows graphic illustration of the noise event, providing fast interpretation and communication of the measured sound. Application of this methodology to the sound of an automotive door closing event is presented here. Representative door closing sound events are analyzed, with correlation presented between the attributes above to dynamic events of the physical hardware within the door and vehicle systems. Modifications of the door-in-white, internal door hardware, seal systems and additional content are investigated for their effect on the sound quality of the door closing event. Finally, recommended values for these attributes are presented.

The application of Statistical Energy Analysis (SEA) to vehicle development is discussed, with a new technique to implement noise path analysis within a SEA model to enable efficient solution and optimization of acoustic trim. A whole vehicle Performance-Based SEA model is used, in which Sound Transmission Loss (STL) and acoustic absorption coefficient characterize subsystem performance. In such a model, the net contribution from each body panel/path, such as the floor, to a specific interior subsystem, such as the driver's head space, is extremely important for vehicle interior noise development. First, it helps to identify the critical path to root-cause potential problems. Second, it is necessary in order to perform balancing of path contributions. With current software, the power based noise contribution analysis is for direct paths/adjacent subsystems.

Techniques have been developed to model friction induced vibration and these were applied to the brake moan of a vehicle. A vehicle system model and the MSC/NASTRAN solutions for geometric nonlinear and complex modes were modified by DMAP for friction input. To assess stability, a position of steady sliding equilibrium was found. Then a complex modes solution was done to find negatively damped modes. Mode shape animation of all the unstable modes showed that there was a 90° out of phase vibration. This produced a design modification on a test vehicle which stabilized the vibration and eliminated brake moan.

A typical problem in integral body vehicles is the isolation of high frequency vibration and noise. A method of attacking this problem is presented for isolation of engine noise. A mount concept which acts as a mechanical low pass filter was analyzed, designed and tested. Results in reducing engine noise in the vehicle show it to be an effective method.

An approximate analysis method for brake squeal is presented. Using MSC/NASTRAN a geometric nonlinear solution is run using a friction stiffness matrix to model the contact between the pad and rotor. The friction coefficient can be pressure dependent. Next, linearized complex modes are found where the interface is set in a slip condition. Since the entire interface is set sliding, it produces the maximum friction work possible during the vibration. It is a conservative measure for stability evaluation. An averaged friction coefficient is measured and used during squeal. Dynamically unstable modes are found during squeal. They are due to friction coupling of neighboring modes. When these modes are decoupled, they are stabilized and squeal is eliminated. Good correlation with experimental results is shown. It will be shown that the complex modes baseline solution is insensitive to the type of variations in pressure and velocity that occur in a test schedule.

The approaches used to develop an NVH package for a vehicle have changed dramatically over the last several years. New noise and vibration control strategies have been introduced, new materials have been developed, advanced testing techniques have been implemented, and sophisticated computer modeling has been applied. These approaches help design NVH solutions that are optimized for cost, performance, and weight. This paper explains the NVH practices available for use in designing vehicles for the new millennium.

Brake squeal has been analyzed by finite elements for some time. Among several methods, complex eigenvalue analysis is proving useful in the design process. It requires hardware verification and it falls into a simulation process. However, it is fast and it can provide guidance for resolving engineering problems. There are successes as well as frustrations in implementing this analysis tool. Its capability, robustness and reliability are closely examined in many companies. Generally, the low frequency squealing mechanism is a rotor axial direction mode that couples the pads, rotor, and other components; while higher frequency squeal mainly exhibits a rotor tangential mode. Design modifications such as selection of rotor design, insulator, chamfer, and lining materials are aimed specifically to cure these noise-generating mechanisms. In GM, complex eigenvalue analysis is used for brake noise analysis and noise reduction. Finite element models are validated with component modal testing.

THIS description of the hydraulic control used with the hydra-matic transmission reveals how the control operates to change ratios under power without direction from the driver. The control's pattern of automatic shifting for ordinary, high-range driving has been selected as the best compromise between top performance and low ratio of engine noise to wind noise. The control's low range shifts gears according to performance dictates alone, furnishing greater power for extreme conditions at low speeds and enabling the driver to use his engine as a brake on steep descents. Heart of the control system is a double hydraulic governor, sensitive both to car speed and throttle opening. THIS paper, as well as the two that follow, one by Messrs. Nutt and Smirl and the other by Mr. Kimberly, make up a symposium on automatic transmission components presented at the 1947 SAE Summer Meeting.

This paper documents a joint development process between General Motors and Dow Automotive to improve primary body structure frequencies on the GM family of midsize vans by utilizing cavity-filling structural foam. Optimum foam locations, foam quantity, and foam density within the body structure were determined by employing both math-based modeling and vehicle hardware testing techniques. Finite element analysis (FEA) simulations of the Body-In-White (BIW) and “trimmed body” were used to predict the global body structure modes and associated resonant frequencies with and without structural foam. The objective of the FEA activity was to quantify frequency improvements to the primary body structure modes of matchboxing, bending, and torsion when using structural foam. Comprehensive hardware testing on the vehicle was also executed to validate the frequency improvements observed in the FEA results.