Search Results

A program has been completed to evaluate ultra-low sulfur diesel fuels and passive diesel particulate filters (DPFs) in truck and bus fleets operating in southern California. The fuels, ECD and ECD-1, are produced by ARCO (a BP Company) and have less than 15 ppm sulfur content. Vehicles were retrofitted with two types of catalyzed DPFs, and operated on ultra-low sulfur diesel fuel for over one year. Exhaust emissions, fuel economy and operating cost data were collected for the test vehicles, and compared with baseline control vehicles. Regulated emissions are presented from two rounds of tests. The first round emissions tests were conducted shortly after the vehicles were retrofitted with the DPFs. The second round emissions tests were conducted following approximately one year of operation. Several of the vehicles retrofitted with DPFs accumulated well over 100,000 miles of operation between test rounds.

Off-Highway diesel engines may benefit from exhaust emission control systems developed for on-highway vehicles. Both the diesel oxidation catalyst and the catalytic soot filter are being used to remove diesel smoke and odor. The advantages of both of these technologies are explained. NOx emissions control from diesel engines are now being addressed. Alternate fuels, such as methanol or natural gas, have been designed to replace diesel fuel as a measure to control NOx emissions. To avoid transfer to alternate fuels and permit continued use of diesel fuel in diesel engines, two approaches are being studied. These are the use of exhaust gas recirculation (EGR) and the development of a new technology called a lean NOx reduction catalyst. EGR, if successfully developed, probably will require the use of a catalytic soot filter. Lean NOx catalysts have been developed but still are not at a practical stage yet.

Many studies suggest that lean-NOx SCR proceeds via oxidation of NO to NO2 by oxygen, followed by the reaction of the NO2 with hydrocarbons. On catalysts that are not very effective in catalyzing the equilibration of NO+O2 and NO2, the rate of N2 formation is substantially higher when the input NOx is NO2 instead of NO. The apparent bifunctional mechanism in the SCR of NOx has prompted the use of mechanically mixed catalyst components, in which one component is used to accelerate the oxidation of NO to NO2, and another component catalyzes the reaction between NO2 and the hydrocarbon. Catalysts that previously were regarded as inactive for NOx reduction could therefore become efficient when mixed with an oxidation catalyst. Preconverting NO to NO2 opens the opportunity for a wider range of SCR catalysts and perhaps improves the durability of these catalysts. This paper describes the use of a non-thermal plasma as an efficient means for selective partial oxidation of NO to NO2.

A family of cordierite DPF filters were developed and studied for their efficacy for catalyzed soot filter applications. In addition to porosity and median pore size of DPF filters, breadth of pore size distribution, microstructure, and pore connectivity have a profound influence not only in filter performance (pressure drop, catalyst coatability, and filtration efficiency) but also on mechanical and physical properties. Through filter material composition development, optimum values for the %porosity, median pore diameter, and breadth of the pore size distribution for minimizing pressure drop have been identified, leading to the development of a new family of high-porosity cordierite diesel particulate filters that possess a unique combination of high filtration efficiency, high strength, and very low clean and soot-loaded pressure drop in both the catalyzed and non-catalyzed states. By controlling the microstructure, the impact of the catalyst on pressure drop has been minimized.

A multi-year technology validation program was completed in 2001 to evaluate ultra-low sulfur diesel fuels and passive diesel particle filters (DPF) in several different diesel fleets operating in Southern California. The fuels used throughout the validation program were diesel fuels with less than 15-ppm sulfur content. Trucks and buses were retrofitted with two types of passive DPFs. Two rounds of emissions testing were performed to determine if there was any degradation in the emissions reduction. The results demonstrated robust emissions performance for each of the DPF technologies over a one-year period. Detailed descriptions of the overall program and results have been described in previous SAE publications [2, 3, 4, 5]. In 2002, a third round of emission testing was performed by NREL on a small subset of vehicles in the Ralphs Grocery Truck fleet that demonstrated continued robust emissions performance after two years of operation and over 220,000 miles.

The application of SCR deNOx aftertreatment was studied on two about 12 liter class heavy-duty diesel engines within a consortium project. Basically, the system consists of a dosage system for aqueous urea injection and a vanadia based SCR catalyst, without an upstream or downstream oxidation catalyst. The urea injection system for a DAF and a Renault V.I. (Véhicules Industriels) diesel engine was calibrated on the engine test bench taking into account dynamic effects of the catalyst. For both engine applications NOx reduction was 81% to 84% over the ESC and 72% over the ETC. CO emission increased up to 27%. PM emission is reduced by 4 to 23% and HC emission is reduced by more than 80%. These results are achieved with standard diesel fuel with about 350 ppm sulfur. The test engines and SCR deNOx systems were built into a DAF FT95 truck and a Renault V.I. Magnum truck.

The emission capability of an exhaust system tuned for improved engine performance from an in-line four-cylinder engine has been investigated. The exhaust system comprises two close-coupled catalysts; each located in separate exhaust streams and has been termed the 4-2 close-coupled catalysts (CCC) -1 system. It has been shown that, given equivalent total catalyst volume, this system configuration results in compromised high exhaust flow rate emissions performance compared with a single catalyst (4-1semi-CCC) system. This emissions performance deficit has been attributed to the effect of engine frequency flow pulsations, which result in relatively high peak space velocities in the 4-2CCC-1 system despite the mean space velocity being consistent. Engine-based AFR Bias Sweep tests suggest that hydrocarbon emissions are most strongly affected by this phenomenon. At lower exhaust flow rates, the difference in performance between the two systems is negligible.

In the effort to design reliable diesel engines which meet the strict US Federal Regulations for emissions, considerable progress has been made by engine manufacturers. Particulate emissions are now below 0.25 g/BHPh and after 1994 will be below 0.1 g/BHPh. Diesel fuel has a revised specification limit of 0.05% sulfur as a means to assist diesel engine manufacturers in complying with the 1994 standard. Diesel oxidation catalysts (DOC) have been chosen as another means. A DOC can efficiently oxidize soluble organic particulate matter (SOF) and gaseous hydrocarbons while easily oxidizing SO2 to SO3-the latter being a particulate and undesirable. Selective DOCs have been developed which maintain the activity for SOF and minimize the undesirable SO2 oxidation step. However, performance for gaseous hydrocarbons may be negatively affected.

A recently completed program was developed to evaluate ultra-low sulfur diesel fuels and passive diesel particle filters (DPF) in several different truck and bus fleets operating in Southern California. The primary test fuels, ECD and ECD-1, are produced by ARCO, a BP company, and have less than 15 ppm sulfur content. A test fleet comprised of heavy-duty trucks and buses were retrofitted with one of two types of catalyzed diesel particle filters, and operated for one year. As part of this program, a chemical characterization study was performed in the spring of 2001 to compare the exhaust emissions using the test fuels with and without aftertreatment. A detailed speciation of volatile organic hydrocarbons (VOC), polycyclic aromatic hydrocarbons (PAH), nitro-PAH, carbonyls, polychlorodibenzo-p-dioxins (PCDD) and polychlorodibenzo-p-furans (PCDF), inorganic ions, elements, PM10, and PM2.5 in diesel exhaust was performed for a select set of vehicles.

Recently, catalyzed soot filters (CSF) for passenger vehicles have been introduced into the marketplace to comply with the European environmental requirements and future emission standards. The initial system consisted of one or two diesel oxidation catalysts (DOC) to meet the regulated HC and CO standards along with an under floor CSF to treat the particulate emissions. In order to meet the cold start requirements and to reduce system costs with a CSF only unit, converters are placed closer to the engine to minimize heat losses and more of the DOC functionality is integrated into the filter substrate. This work describes the development of such DOC-integrated CSF systems. One major challenge in the design of such systems is to ensure that there is sufficient catalyst functionality within the wall-flow substrate while maintaining an acceptable exhaust gas backpressure across the filter.

Catalytic control of motorcycle vehicle emissions requires that the catalytic element be carefully integrated into the exhaust system. The catalyst element physical parameters are optimized to achieve specific exhaust tuning requirements. Since the converter is located inside the muffler, the peak temperatures can severely stress both the catalytic active washcoat materials and the currently used metal monolith structure under some operating conditions. This paper addresses the development of an alternative ceramic monolithic catalyst that can be used for 2 and 4-stroke motorcycle applications. A new mounting technique was developed to contain the ceramic catalytic unit within a holder or converter shell with sufficient strength and durability to withstand the severe environment of 2-stroke engine exhaust.

Diesel engines are far more efficient than gasoline engines of comparable size, and emit less greenhouse gases that have been implicated in global warming. In 2000, the US EPA proposed very stringent emissions standards to be introduced in 2007 along with low sulfur (< 15 ppm) diesel fuel. The California Air Resource Board (CARB) has also established the principle that future diesel fueled vehicles should meet the same low emissions standards as gasoline fueled vehicles and the EPA followed suit with its Tier II emissions regulation. Achieving such low emissions cannot be done through engine development and fuel reformulation alone, and requires application of NOx and particulate matter (PM) aftertreatment control devices. There is a widespread consensus that NOx adsorbers and particulate filter are required in order for diesel engines to meet the 2007 emissions regulations for NOx and PM. In this paper, the key exhaust characteristics from an advanced diesel engine are reviewed.