Search Results

Gasoline fueled Homogeneous Charge Compression Ignition (HCCI) combustion with internal exhaust gas re-circulation using Negative Valve Overlap (NOL) was investigated by means of calculation and experiment in order to apply this technology to practical use with sufficient operating range and with acceptable emission and fuel consumption. In this paper we discuss the basic characteristics of NOL-HCCI with emphasis on the influence of intake valve timing on load range, residual gas fraction and induction air flow rate. Emission and fuel consumption under various operation conditions are also discussed. A water-cooled 250cc single cylinder engine with a direct injection system was used for this study. Three sets of valve timing were selected to investigate the effect of intake valve opening duration. Experimental results demonstrated that an engine speed of approximately 2000rpm yields an NMEP (Net Mean Effective Pressure) range from 200kPa to 400kPa.

The authors used auxiliary gas injection (AGI) to increase in-cylinder mixing during the latter portion of combustion in a direct injection (DI) diesel engine in order to reduce soot emissions without affecting NOx. Experiments were conducted using various gas injection directions and compositions to explore the effect of these parameters. Simulations were employed to provide additional insight. AGI direction was found to have a profound impact on soot emissions. Researchers suggested that this was due to changes in the fuel spray-gas jet interaction with injection direction. Simulations supported this theory and suggested that the number of soot clouds affected by the gas jet may also be a factor. The oxygen content of the gas jet was also found to have an influence on emissions. Researchers found that, when the oxygen content of the gas jet was increased, soot emissions decreased. However, this was found to have a detrimental affect on NO.

Many commercial fuels, including gasoline and diesel, are multicomponent hydrocarbons. During the fuel vaporization process, the volatile components evaporate first, which dominate the region near the nozzle exit. The lately evaporated vapor with high penetration has high molecular weight. Thus, ignition and combustion of multicomponent fuels are not only influenced by distribution of fuel vapor mass fraction, but also by distribution of the components. This paper presents a spark ignition and combustion model with consideration of such multicomponent effects for GDI engines. Ignition kernel growth due to flame front propagation is considered in the model to eliminate the sensitivity of the numerical mesh size on the results.

An integrated system model containing sub-models for a diesel engine, NOx and soot emissions, and a diesel particulate filter (DPF) has been used to simulate stead-state engine operating conditions. The simulation results have been used to investigate the effect of DPF loading and passive regeneration on engine performance and emissions. This work is the continuation of previous work done to create an overall diesel engine/exhaust system integrated model. As in the previous work, a diesel engine, exhaust system, engine soot emissions, and diesel particulate filter (DPF) sub-models have been integrated into an overall model using Matlab Simulink. For the current work new sub-models have been added for engine-out NOx emissions and an engine feedback controller. The integrated model is intended for use in simulating the interaction of the engine and exhaust aftertreatment components.

The use of low temperature combustion (LTC) modes has demonstrated abilities to lower diesel engine emissions while maintaining good fuel consumption. LTC is assumed to be a viable solution to assist in meeting stringent upcoming diesel engine emissions targets, particularly nitric oxides (NOx) and particulate matter (PM). However, LTC is currently limited to low engine loads and is not a feasible solution at higher loads on production engines. A mixed mode combustion strategy must be implemented to take advantage of the benefits offered from LTC at the low loads and speeds while switching to a conventional diesel combustion strategy at higher loads and speeds and thus allowing full range use of the engine under realistic driving conditions. Experiments were performed to characterize engine out emissions during transient engine operating conditions involving LTC combustion strategies.

An overall diesel engine and aftertreatment system model has been created that integrates diesel engine, exhaust system, engine emissions, and diesel particulate filter (DPF) models using MATLAB Simulink. The 1-D engine and exhaust system models were developed using WAVE. The engine emissions model combines a phenomenological soot model with artificial neural networks to predict engine out soot emissions. Experimental data from a light-duty diesel engine was used to calibrate both the engine and engine emissions models. The DPF model predicts the behavior of a clean and particulate-loaded catalyzed wall-flow filter. Experimental data was used to validate this sub-model individually. Several model integration issues were identified and addressed. These included time-step selection, continuous vs. limited triggering of sub-models, and code structuring for simulation speed. Required time-steps for different sub models varied by orders of magnitude.

An integrated system model containing sub-models for diesel engine, emissions, and aftertreatment devices has been developed. The objective is to study engine-device and device-device interactions. The emissions sub-models used are for NOx and PM (particulate matter) prediction. The aftertreatment sub-models used include a diesel oxidation catalyst (DOC) and a diesel particulate filter (DPF). Controllers have also been developed to allow for transient simulations, active DPF regeneration, and prevention/control of runaway DPF regenerations. The integrated system-level model has been used to simulate DPF regeneration via exhaust fuel injection ahead of the DOC. In addition, the controller model can use intake throttling to assist in active DPF regeneration if needed. Regeneration studies have been done for both steady engine load and with load transients. High to low engine load transients are of particular interest because they can lead to runaway DPF regeneration.

A single cylinder CFR research engine has been run in HCCI combustion mode for a range of temperatures and fuel compositions. The data indicate that the best HCCI operation, as measured by a combination of successful combustion with low ISFC, occurs at or near the rich limit of operation. Analysis of the pressure and heat release histories indicated the presence, or absence, and impact of the fuel's NTC ignition behavior on establishing successful HCCI operation. The auto-ignition trends observed were in complete agreement with previous results found in the literature. Furthermore, analysis of the importance of the fuel's octane sensitivity, through assessment of an octane index, successfully explained the changes in the fuels auto-ignition tendency with changes in engine operating conditions.