Search Results

Engine downsizing is one of the most promising alternatives for improving fuel economy, while maintaining good emission and NVH behavior. However, the development of a small displacement HSDI Diesel engine with 4-valve technology represents a significant challenge, especially with regard to the design of the top end. This paper summarizes the technical challenges that were overcome to incorporate product requirements for combustion behavior, NVH-performance, and production feasibility during the top end design of the new Ford 1.2 Liter HEV engine. This engine is a state-of-the-art HSDI Diesel engine which features a high pressure common rail fuel injection system, 4-valve cylinder head, cooled EGR, port deactivation, and variable nozzle turbocharger (VNT) technologies. Initial test results with the first prototypes of the 1.2 Liter DIATA engine verify that downsizing can successfully be performed.

The sound quality and performance of an automotive engine are both significantly influenced by the “air-to-air” system, i.e., the intake system, the exhaust system, and the engine gas dynamics. Only a full systems approach can result in an optimized air-to-air system, which fulfills engine performance requirements, overall sound pressure level targets for airborne vehicle noise, as well as sound quality demands. This paper describes an approach, which considers the intake system, engine, and exhaust system within one CAE model that can be utilized for engine performance calculations as well as acoustic simulations. Examples comparing simulated and measured sound are discussed. Finally, the simulated sound (e.g., at the tailpipe of the exhaust system) is combined with an interior noise simulation technique to evaluate its influence inside the vehicle's interior.

The shifter lever is one of the main customer contact points in the vehicle. Vibration levels at this contact point have an effect on perceived vehicle quality. For this reason, shifter lever vibration and the corresponding transfer paths from the transmission to the shifter lever need to be considered during vehicle development. On a recent program, experimental measurements identified the shifter cable to be a significant transfer path for shifter lever vibration. An integrated Computer Aided Engineering (CAE) and experimental effort was undertaken to model and optimize the shifter lever and cable assembly for reduced vibration. Experimental data was used to better understand the vibration phenomenon, set boundary conditions for the CAE modeling, and for correlation. The CAE model contains the shifter lever assembly and a detailed cable assembly model.

Based on the TurboDISI engine presented earlier [1], [2], a new Spray Guided Turbo (SGT) concept with enhanced engine performance was developed. The turbocharged engine was modified towards utilizing a spray-guided combustion system with a central piezo injector location. Higher specific power and torque levels were achieved by applying specific design and cooling solutions. The engine was developed utilizing a state-of-the-art newly developed charge motion design (CMD) process in combination with single cylinder investigations. The engine control unit has a modular basis and is realized using rapid prototyping hardware. Additional fuel consumption potentials can be achieved with high load EGR, use of alternative fuels and a hybrid powertrain. The CO2 targets of the EU (120 g/km by 2012 in the NEDC) can be obtained with a mid-size vehicle applying the technologies presented within this paper.

The opposed piston opposed cylinder (opoc™) engine concept has been demonstrated as an engine concept with high specific power density and high power to volume ratio. The engine has several potential applications, including use as an auxiliary power unit (APU) in various commercial and military applications and as the primary power source for small unmanned air vehicles (UAVs). An engine in this power range operating on heavy fuels (e.g. JP5, JP8, DF2) is not typically available. The engine uses a two-cycle supercharged uniflow scavenging system with asymmetric port timing and will run at speeds between 8,000 and 12,000 rpm. The unique design of the opoc™ engine produces a piston speed that is half the speed of a typical crankshaft engine running at the same speed. Uniflow scavenging produces gas exchange efficiencies rivaling those of four-cycle engines. The design also leads to reduced in-cylinder heat losses. Furthermore, the opoc™ engine is fully balanced.

The new opoc™ diesel engine concept was presented at the SAE 2005 World Congress [1]. Exceptional power density of >1hp/lb and >40% efficiency have been predicted for the 2-stroke opoc™ diesel engine concept. Intensive CAE simulations have been performed during the concept and design phase in order to define the baseline scavenging and combustion parameters, such as port timing, turbocharger configuration and fuel injection nozzle design. Under a DARPA contract, first prototype engines have been built and have undergone a validation testing program. The main goal of the first testing phase was to demonstrate the power output capability of the new engine concept. In close relationship and interaction of testing and CAE simulation, the uniflow scavenging process and parameters of the special diesel direct side injection have been optimized. This paper discusses the latest results of the opoc engine development.

NVH refinement of passenger vehicles is crucial to customer acceptance of contemporary vehicles. This paper describes the vehicle NVH development process, with specific examples from a Diesel sedan application that was derived from gasoline engine-based vehicle architecture. Using an early prototype Diesel vehicle as a starting point, this paper examines the application of a Vehicle Interior Noise Simulation (VINS) technique in the development process. Accordingly, structureborne and airborne noise shares are analyzed in the time-domain under both steady-state and transient test conditions. The results are used to drive countermeasure development to address structureborne and airborne noise refinement. Examples are provided to highlight the refinement process for “Diesel knocking” under idle as well as transient test conditions. Specifically, the application of VINS to understanding the influence of high frequency dynamic stiffness of hydro-mounts on Diesel clatter noise is examined.

Due to the future application of combustion engines in small and hybrid vehicles, the demand for high efficiency with low mass and compact engine design is of prime importance. The diesel engine, with its outstanding thermal efficiency, is a well suited candidate for such applications. In order to realize these targets, future diesel engines will need to have increasingly higher specific output combined with increased power to weight ratios. This is therefore driving the need for new designs of 3 and/or 4 cylinder, small bore engines of low displacement, sub 1.5l. Recent work on combustion development, has shown that combustion systems, ports, valves and injector sizes are available for bore sizes down to 65 mm.

The U.S. Tier 2 emission regulations require sophisticated exhaust aftertreatment technologies for diesel engines. One of the projects under the U.S. Department of Energy's (DOE's) Advanced Petroleum Based Fuels - Diesel Emission Controls (APBF-DEC) activity focused on the development of a light-duty passenger car with an integrated NOx (oxides of nitrogen) adsorber catalyst (NAC) and diesel particle filter (DPF) technology. Vehicle emissions tests on this platform showed the great potential of the system, achieving the Tier 2 Bin 5 emission standards with new, but degreened emission control systems. The platform development and control strategies for this project were presented in 2004-01-0581 [1]. The main disadvantage of the NOx adsorber technology is its susceptibility to sulfur poisoning. The fuel- and lubrication oil-borne sulfur is converted into sulfur dioxide (SO2) in the combustion process and is adsorbed by the active sites of the NAC.

A hydraulic free-piston engine (FPE), which converts combustion energy directly to hydraulic energy, is being developed by the U. S. EPA due to its potential as a lower-cost and higher-efficiency prime mover for hydraulic series hybrid vehicles. Two prototype engines were designed, fabricated and tested: a two-cylinder engine operating primarily with a two-stroke compression-ignition, direct-injection (CIDI) cycle and a six-cylinder engine operating with a four-stroke CIDI cycle. These engines successfully achieved up to 39% peak hydraulic efficiency under continuously fired operation, while demonstrating exceptional repeatability and control of the cylinder compression ratio. A basic description of the engine design, along with the initial test results from these two prototypes, is presented below.

Internal combustion engine noise is primarily composed of combustion and mechanical noise shares. Mechanical noise contributions in engines have increased relevance at low load conditions when combustion related noise is not significant. Current literature on mechanical noise in engines includes: piston pin ticking, piston secondary motion, and valvetrain impacts. A mechanical noise source from excitation of piston tertiary motion is described here in the form of a case study on an engine exhibiting a cold start “clatter” noise. Targeted experimental measurements were initially used to rule out potential mechanisms such as impacts resulting from piston pin ticking and piston secondary motion. Experimental modification studies and piston load and kinematics modeling led to discovery of instability of the piston which is understood to excite tertiary motion of the piston and result in impulsive “clatter” noise under certain low load/speed conditions.

A customer's perception of vehicle quality very closely parallels the noise vibration and harshness (NVH) characteristics of the vehicle. Consequently, automotive manufacturers are investing significant resources into optimizing the NVH performance of their vehicles. Automatic transmission shift quality is one of a number of attributes where NVH optimization is critical towards providing customers with a pleasant driving experience. This paper addresses various aspects of understanding, quantifying and optimizing a vehicle's shift quality characteristics. Following an introductory treatment of automatic transmission planetary gear systems, the interaction between the engine/transmission system during shifts is summarized. Various shift quality metrics used to quantify a vehicle's response and its sensitivity to transient inputs are provided. Approaches to manage the engine torque output during the shifts are discussed.

NVH refinement is an important aspect of the powertrain development process. Powertrain NVH refinement is influenced by overall sound levels as well as sound quality. The sound quality and hence the level of powertrain NVH refinement can be negatively affected by the presence of excessive impulsive noise. This paper describes a process used to develop an understanding of impulsive powertrain noise. The paper begins with an introductory discussion of various sources of impulsive noise in an automotive powertrain. Following this, the paper outlines a process for identifying the source of the impulsive powertrain noise using examples from case studies. The remainder of the paper focuses on certain examples of impulsive noise such as Diesel knocking noise, injector ticking, impulsive cranktrain noise, and gear rattle. For these examples, the development of key objective metrics, optimization measures, and improvement potential are examined.

Optimization of the interface between the powerplant and vehicle frame/body is critical to obtaining superior interior structureborne noise and vibration characteristics in the vehicle. This paper demonstrates the combination of new and existing simulation/experimental methodologies for powerplant integration, including results from case studies. Multi-body simulation based methodologies are used to optimize the location, number, and type of powerplant mounts on a vehicle, taking into account the input forcing from the engine and frequency-dependent mount properties. Upon obtaining the first prototype vehicle, a procedure to evaluate the effectiveness of the powerplant mounts using a vibrational power flow technique, is described. The influence of mount bracket resonances on interior vehicle sound is shown and a new procedure to optimize mount brackets, provided.

Customer requirements for quiet and more comfortable vehicles have steadily increased. Requirements for lightweight vehicle designs and the need for more fuel efficient engines are often contradictory to the customer expectations for NVH refinement. The driveline can be a significant source of NVH issues in the vehicle. The increasing complexity of modern driveline systems as well as the existence of several variants in the driveline architecture (front wheel, rear wheel and four-wheel/all-wheel drive, automatic-, manual-, automatic-shifted manual transmission, etc.) can make the driveline integration task very challenging. Due to the multitude of driveline components and potential driveline excitations sources, several driveline-related noise and vibration problems within different frequency ranges have to be understood and controlled to ensure a well refined vehicle.

The small-displacement direct-injection (DI) diesel engine is a prime candidate for future transportation needs because of its high thermal efficiency combined with near term production feasibility. Ford Motor Company and FEV Engine Technology, Inc. are working together with the US Department of Energy to develop a small displacement DI diesel engine that meets the key challenges of emissions, NVH, and power density. The targets for the engine are to meet ULEV emission standards while maintaining a best fuel consumption of 200g/kW-hr. The NVH performance goal is transparency with state-of-the-art, four-cylinder gasoline vehicles. Advanced features are required to meet the ambitious targets for this engine. Small-bore combustion systems enable the downsizing of the engine required for high fuel economy with the NVH advantages a four- cylinder has over a three-cylinder engine.

In a gasoline engine, the unswept in-cylinder residual gas and introduction of external EGR is one of the important means of controlling engine raw NOx emissions and improving part load fuel economy via reduction of pumping losses. Since the trapped in-cylinder Residual Gas Fraction (RGF, comprised of both internal, and external) significantly affects the combustion process, on-line diagnosis and monitoring of in-cylinder RGF is very important to the understanding of the in-cylinder dilution condition. This is critical during the combustion system development testing and calibration processes. However, on-line measurement of in-cylinder RGF is difficult and requires an expensive exhaust gas analyzer, making it impractical for every application. Other existing methods, based on measured intake and exhaust pressures (steady state or dynamic traces) to calculate gas mass flowrate across the cylinder ports, provide a fast and economical solution to this problem.