Search Results

Due to the contradiction of the market demands and legal issues OEMs are forced to invest in finding concepts that assure high fuel economy, low exhaust emissions and high specific power at the same time. Since mechanical losses may amount up to 10 % of the fuel energy, a key to realise such customer/government specific demands is the improvement of the mechanical performance of the engines, which comprises mainly friction decrease and lightweight design of the engine parts. In order to achieve the mentioned objectives, it has to be checked carefully for each component whether the design potentials are utilized. Many experimental studies show that there is still room for optimization of the cranktrain parts, especially for the crankshaft. A total exploitation of the crankshaft potentials is only possible with advanced calculation approaches that ensure the component layout within design limits.

The main assignment of Controlled Auto Ignition (CAI) operation range expansion is to reduce the burn rate or combustion noise at high load and to minimize misfire at low load. The potential of two principal EGR strategies is well known to initiate CAI in a wide range of operation map by using a variable train system: the Exhaust Port Recirculation (EPR) for higher part load and the Combustion Chamber Recirculation (CCR - also called Negative Valve Overlap) for lower part load. However the detailed comparison of the ignition phenomena with each EGR strategy has not been fully studied yet. In this paper, EPR and CCR were compared with same operational condition (engine speed and load). For the analysis, flame luminescence and Raman scattering method for optical measurement and STAR-CD (CD-adapco) for numerical simulation are used.

In the last few years the requirement to optimize powertrain noise and vibration has increased significantly. This was caused by the demand to fulfill the vehicle's exterior noise legislative limits in Europe, and by increased customer awareness for high ride comfort. Much effort concentrated on the engine and the powertrain as prime sources of noise and vibration in a vehicle. The cranktrain with its moving components is a significant source of noise and vibration excitation within the engine. This paper describes results of investigations to evaluate various design alternatives in respect to NVH. The influences of crankshaft material, of balancing rate and of secondary shaking forces are discussed, with the aim to evaluate these various design options.

This paper reports the results of theoretical and experimental investigations in the field of variable intake - valve control of spark-ignition engines. Different degrees of freedom for a variable intake profile such as variable intake opening and closing events, variable valve lift, as well as the deactivation of one of the intake valves per cylinder of a multi-valve engine are considered and evaluated concerning their potential to reduce pumping losses, to support mixture formation, and to improve combustion. The investigations show that additional efforts are necessary to convert the potential of minimized pumping losses due to unthrottled SI-engine load control into reduced fuel consumption and good driveability. Increased gas velocities during intake for low engine speed and load and adjusted residual-gas fractions according to the different operating conditions prove to be very efficient parameters to improve engine performance under unthrottled conditions.

All reciprocating engines from the first Diesel engine to turbocharged formula 1 engines require a sealing of the combustion chamber. This sealing is realized by the compression rings. Today a set of two compression rings and one oil control ring is standard, the large variety of available solution demonstrate the continuous effort and attention paid to an optimized system performance since the first engine was started. The complexity of the interactions with the mechanical, thermal, thermodynamic, tribologic, dynamic behavior of the piston still requires mechanical testing of the various components before release to series production. This procedure can be shortened by use of simulation models reflecting the real behavior in detail to select the most promising combinations of components and characteristics.

At the present time, combustion process effects on vehicle interior noise can be evaluated only when vehicle and engine are physically available. This Paper deals with a new method for the prediction of combustion process induced vehicle interior noise. The method can be applied already in early combustion system development and allows a time and cost efficient calibration optimization of engine and vehicle. After establishing appropriate transfer weighting functions (engine) and structure transfer functions (vehicle), audible vehicle interior noise is generated based on appropriate cylinder pressure analysis. Combustion process effects on interior noise can be judged subjectively as well as objectively. Thus, combustion process development at the thermodynamic test bench is effectively supported to achieve an optimal compromise with respect to fuel consumption, exhaust emission and interior noise quality.

The current direction for Diesel combustion system development is towards homogenization, in order to reduce particulate and NOx emissions. However, a strong increase of carbon monoxide emissions (CO) is frequently noted in combination with enhanced homogenization. Therefore, the current investigation focuses on a detailed analysis of the particulate - CO trade-off using a laser-optical and multidimensional CFD investigation of the combustion process of a swirl HSDI system. The CFD methodology involves reduced kinetics for soot formation and oxidation and a three-step CO model. These models are validated by a detailed comparison to optical measurements of flow, spray penetration and the spatial distribution of soot, temperature and oxygen concentration. The results obtained show that high concentrations of CO occur as an intermediate combustion reaction product. Subsequently, CO and soot are oxidized in large areas of the combustion chamber.

The loads on the plain bearings of modern combustion engines increase continuously. Reasons for this development are increasing engine speeds on gasoline engines, growing cylinder peak pressures at diesel engines and both combined with the steady trend toward light weight concepts. The still significantly increasing power output of modern engines has to be combined with actions reducing the engine friction losses, as for example smaller bearing dimensions or lower engine oil viscosities. At the same time the comfort, lifetime and engine service interval targets are aggravating boundary conditions. This development leads to the point, where former approaches toward plain bearing layout reach their systematic limitations - a first indication are bearing failures, which occur even though all conventional layout criteria's are fulfilled. Further effects need to be considered to simulate the behavior of the plain bearing under the boundary conditions of a fired combustion engine.

Fuel consumption of a modern combustion engine is significantly influenced by the mechanical friction losses. Particularly in typical city driving, the reduction of the engine friction losses offers a remarkable potential in emission and fuel consumption reduction. The analysis of the engine friction distribution of modern engines shows that the piston group has a high share at total engine friction. This offers a high potential to optimize piston group friction. The paper presents results of recent research and development work in the field of the tribological system piston/piston ring/cylinder bore.

The main function of an engine's lubrication system is to supply the different engine components with sufficient oil under all operating conditions. The demand of modern engines regarding the necessary oil pressure and flow of the individual components is influenced by the engine speeds and the accelerations due to the vehicle driving conditions. In addition to that, the lubrication system effects the following topics: The drive power of the oil pump which is influenced by the oil pump capacity, the oil pressure and mechanical losses of the oil pump. The oil mass which is supplied to the engine oil consumers and flows back via the oil return system to the crankcase and the oil pan. In the crankcase ventilation system, oil and gas have to be separated. The oil aeration due to the oil mass in the crankcase and the moving parts. The ventilation losses in the crankcase which are influenced by the axial ventilation areas and the moved oil mass.

A comparison study on the commonly used solution schemes of one-dimensional gas flow in IC engine manifolds, i.e. the method of characteristics and the finite difference schemes, was conducted in this paper. The study was based on computer simulations of the flow in a typical pipe-volume configuration under both steady and unsteady boundary conditions. The simulation results indicate that all the solution schemes offered fairly good accuracy in parallel pipes under steady flow conditions. However, under unsteady flow conditions, especially in tapered pipes commonly used in IC engine manifolds, all the existing solution schemes encountered difficulties. These included such aspects as the mass and energy conservation, non-physical overshoot, solution stability and physical process distortion. The solution schemes were compared based on the case calculations and the related problems are specified.

This paper introduces different modeling approaches of crankshafts, compares the refinement levels and discusses the difference between the results of the crankshaft durability calculation methodologies. A V6 crankshaft is considered for the comparison of the refinement levels depending on the deviation between the signals such as main bearing forces and deflection angle. Although a good correlation is observed between the results in low speed range, the deviation is evident through the mid to high speed ranges. The deviation amplitude differs depending on the signal being observed and model being used. An inline 4 crankshaft is considered for the comparison of the durability results. The analysis results show that the durability potential is underestimated with a classical crankshaft calculation approach which leads to a limitation of maximum speed of 5500 rpm.

A combined finite element method (FEM), multibody system simulation (MSS), and hydrodynamic (HD) bearing simulation technique can be applied to solve for engine crankshaft and cylinder block dynamics. The cylinder block and crankshaft are implemented in the MSS program as flexible FEM structures. The main bearing oil film reaction is described in the MSS program by a pre-calculated reaction force database. The results are displacements and deformations of the crank train parts and the main bearing reaction forces. Verification of the tool was carried out by comparison of main bearing cap accelerations to measured data.

Based on NVH tests conducted on a heavy-duty turbocharged DI diesel engine, noise relevant differences between steady-state and transient operating condition were investigated. A vehicle drive-by test simulating the effects of vehicle mass and inertia was performed, followed by transient NVH measurements in a semi-anechoic test cell. Steady-state noise was exceeded by 5 dBA during transient operation due to broadband increase of noise excitation combined with structure resonance amplification. Transient noise results mainly from “harsher” combustion as a consequence of enlarged ignition delay indicated by significant increase in maximum cylinder pressure gradient. Variation of geartrain excitation and combustion excitation revealed that geartrain noise is of minor importance in this context.

In order to evaluate the dynamic behavior of IC-engines simulation models are being applied at an ever increasing rate. The simulation models used of until now, were calculation models for an individual valve train. These models were not capable of analysing the interactions of bending and torsional vibrations between individual valve trains of a complete camshaft. For this reason a calculation model has been developed which comprises the entire valve train from the drive gear of the camshaft to the last valve. The camshaft is represented by a combined bending and torsional vibration model with elastic bearings. Combining this model with a camshaft-drive-system simulation model, it is possible to record interactions between the individual valve trains of a complete cylinder head. Bending and torsional effects in the camshaft and effects resulting from the chain or belt forces are taken into consideration.

The distortion of the cylinder liners of internal combustion engines has a significant affect on engine operation. It can affect the lubrication oil consumption, the blow-by, the wear behaviour and due to the friction, the fuel consumption. In order to achieve future requirements regarding exhaust emissions and fuel consumption, the requirements for low cylinder distortion engine blocks will play a significant role. Hence, a new technique to determine liner distortion during fired engine operation was developed.