Search Results

INVOLUTE SPLINES enjoy three major advantages over their straight-sided counterparts: 1. New design concepts have given a more rational approach to clearances and errors. 2. Manufacturing is cheaper and more accurate. 3. Gaging is simpler. Thus, the involute spline standard of SAE and ASA continue to take precedence over the older straight-sided standards.

The current ability of the Virtual Aerodynamic/ Aeroacoustic Wind Tunnel to predict interior vehicle sound pressure levels is demonstrated using an automobile model which has variable windshield angles. This prediction method uses time-averaged flow solutions from a lattice gas CFD code coupled with wave number-frequency spectra for the various flow regimes to calculate the side window vibration from which the sound pressure level spectrum at the driver's ear is determined. These predictions are compared to experimental wind tunnel data. The results demonstrate the ability of this methodology to correctly predict wind noise spectral trends as well as the overall loudness at the driver's ear. A more sophisticated simulation method employing the same lattice gas code is investigated for prediction of the time-accurate flow field necessary to compute the actual side glass pressure spectra.

The present study investigates the wave propagation and attenuation in catalytic converters. The relationships for wave propagation in a catalytic monolith are derived first and then coupled to the wave propagation in tapered ducts. Analytical predictions are compared with experimental results to validate the theory.

This paper describes an investigation into the sound quality of passenger car and light truck closure sounds. The closure sound events that were studied included side doors, hoods, trunklids, sliding doors, tailgates, liftgates, and fuel filler doors. Binaural recordings were made of the closure sounds and presented to evaluators. Both paired comparison of preference and semantic differential techniques were used to subjectively quantify the sound quality of the acoustic events. Major psychoacoustic characteristics were identified, and objective measures were then derived that were correlated to the subjective evaluation results. Regression analysis was used to formulate models which can quantify customers perceptions of the sounds based on the objectively derived parameters. Many times it was found that the peak loudness level was a primary factor affecting the subjective impression of component quality.

Intake and exhaust valve control has been combined with engine calibration control by an on-board computer to achieve a Variable Displacement Engine with improved BSFC during part throttle operation. The advent of the on-board computer, with its ability to provide integrated algorithms for the fast accurate flexible control of the entire powertrain, has allowed practical application of the valve disabler mechanism. The engine calibration basis and the displacement selection criteria are discussed, as are the fuel economy, emissions and behavior of a research vehicle on selected drive cycles ( Metro, Highway and Steady State ). Additionally, the impact upon vehicle driveability and other related subsystems ( e.g., transmission ) is addressed.

Locations of key body segments of Hybrid III dummies used in FMVSS 208 compliance tests and NCAP tests were measured and subjected to statistical analysis. Mean clearance dimensions and their standard deviations for selected body segments of driver and passenger occupants with respect to selected vehicle surfaces were determined for several classes of vehicles. These occupant locations were then investigated for correlation with impact responses measured in crash tests and by using a three dimensional human-dummy mathematical model in comparable settings. Based on these data, the importance of some of the clearance dimensions between the dummy and the vehicle surfaces was determined. The study also compares observed Hybrid III dummy positions within selected vehicles with real world occupant positions reported in published literature.

As part of a general EGR system model, an adiabatic thermodynamic vacuum EGR valve actuator model was developed and validated. The long term goal of the work is improved system operation by correctly specifying and allocating EGR system component requirements.

The feasibility of using experimentally determined flow fields at intake valve closing, IVC, as initial conditions for computing the in-cylinder flow dynamics during the compression stroke is demonstrated by means of a computer simulation of the overall approach. A commercial CFD code, STAR-CD, was used for this purpose. The study involved two steps. First, in order to establish a basis for comparison, the in-cylinder flow field throughout the intake and compression strokes, from intake valve opening, IVO, to top dead center, TDC, was computed for a simple engine geometry. Second, experimental initial conditions were simulated by randomly selecting and perturbing a set of velocity vectors from the computed flow field at IVC.

In nowadays market, highlighted by global products, companies are pushed to sell products that comply with legal and customer requirements in different countries and, not unusually, different continents. In order to achieve such challenge, and pressed to reduce project and production costs, companies are spreading design centers around the world, based on regional expertise. These excellence centers must work together to benefit from synergies and local skills from different regions. Such projects are staffed by Virtual Team (BINDER, 2007), whose members barely face each other. This means teams will work frequently with people they have never met, who live on different time zones and have different cultures. As a consequence, communication is done basically through computer-based media, mainly based on emailing, and must be even clearer and more direct than with the people who work on the next desk.

Because it is common to attach plastic parts to other plastic, metal, or ceramic assemblies with mechanical fasteners that are often stronger and stiffer than the plastic with which they are mated, it is important to be able to predict the retention of the fastener in the polymeric component. The ability to predict this information allows engineers to more accurately estimate length of part service life. A study was initiated to understand the behavior of threaded fasteners in bosses molded from engineering thermoplastic resins. The study examined fastening dynamics during and after insertion of the fastener and the effects of friction on the subsequent performance of the resin. Tests were conducted at ambient temperatures over a range of torques and loads using several fixtures that were specially designed for the study. Materials evaluated include modified-polyphenylene ether (M-PPE), polyetherimide (PEI), polybutylene terephthalate (PBT), and polycarbonate (PC).

A series of tests were conducted to determine the potential for reducing vehicle underhood temperatures by either 1) diverting the radiator fan air flow from the engine compartment or 2) by forced air cooling of the exhaust manifold in conjunction with shielding it or 3) by a combination of the two methods. The test vehicle was a Ford F-250 Light Truck with a 7.5L V-8 engine. The vehicle was tested in a dynamometer cell equipped with cell blowers to simulate road speed conditions. It was found that diverting the outlet air from the radiator will reduce underhood component temperatures when the vehicle is in motion and also at normal idle. However, if the vehicle is to be used for power takeoff applications requiring a “kicked” idle, then forced cooling of the exhaust manifolds is also required to maintain reduced underhood temperatures. A combination of these two techniques maximized the reduction of underhood temperatures for all operating conditions tested.

Exhaust pressures (P3) are hard parameters to measure and can be readily estimated, the cost of the sensors and the temperature in the exhaust system makes the implementation of an exhaust pressure sensor in a vehicle control system a costly endeavor. The contention with measured P3 is the accuracy required for proper engine and vehicle control can sometimes exceed the accuracy specification of market available sensors and existing models. A turbine inlet exhaust pressure observer model based on isentropic expansion and heat transfer across a turbocharger turbine was developed and investigated in this paper. The model uses 4 main components; an open loop P3 orifice flow model, a model of isentropic expansion across the turbine, a turbine and pipe heat transfer models and an integrator with the deviation in the downstream turbine outlet parameter.

The “Information Age” and the growth of electronics on vehicles are driving forces behind the “personalized” vehicle. The vision is a responsive vehicle where the powertrain, ride, instrumentation and interior can be customized by the driver. A strategy to personalize the vehicle is presented; first, through market research to identify new features, and second, ergonomic design for easy to use displays and controls. Changes in society that are driving forces are discussed along with the counter balancing need for ergonomic design. Approaches to personalization, ergonomic principles, and technologies are presented.

This paper identifies and analyzes steady-state and transient tire properties affecting vehicle directional response characteristics. The study is limited to the relationship between lateral force and slip angle. It shows fundamental differences between steady-state and transient properties. Tire transient properties are described by a force-slip angle loop with cornering stiffness and dynamic lateral force offset as parameters. Cornering stiffness is presented as a variable that changes with speed and steer rate. An interrelationship between cornering stiffness and dynamic lateral force offset resulting from the time lag between lateral force and slip angle is shown. Ramp steer techniques for measuring transient tire properties on a road trailer and on an external drum machine are described. A need for transient tire data for computer simulations of vehicle transient steer maneuvers is shown.

Speciated HC emissions from the exhaust system of a production engine without an active catalyst have been obtained with 3 sec time resolution during a 70°F cold start using two control strategies. For the conventional cold start, the emissions were initially enriched in light fuel alkanes and depleted in heavy aromatic species. The light alkanes fell rapidly while the lower vapor pressure aromatics increased over a period of 50 sec. These results indicate early retention of low vapor pressure fuel components in the intake manifold and exhaust system. Loss of higher molecular weight HC species does occur in the exhaust system as shown by experiments in which the exhaust system was preheated to 100° C. The atmospheric reactivity of the exhaust HC emissions for photochemical smog formation increases as the engine warms.

The recent development of TiAl-based alloys by the aerospace community has provided an excellent material alternative for hot components in automotive engines. The low density combined with an elevated temperature strength similar to that of Ni-base superalloys make TiAl-based alloys very attractive for exhaust valve applications. Lighter weight valvetrain components improve performance and permit the use of lower valve spring loads which reduce noise and friction and enhance fuel economy. However, difficult fabricability and a perception that TiAl alloys are high cost, low volume aerospace materials must be overcome in order to permit consideration for use in high-volume automotive applications. This paper provides a comparison of properties for several exhaust valve alternative materials. The density of TiAl alloys is lower than Ti alloys with creep and fatigue properties equivalent to IN-751, a current high performance exhaust valve material.

In the 1999 Supplemental Notice for Proposed Rulemaking (SNPRM) for Advanced Airbags, the National Highway Traffic Safety Administration (NHTSA) sought comments on the maximum speed at which the high-speed, unbelted occupant test suite will be conducted, i.e., 48 kph vs. 40 kph. To help address this question, an analysis of constraints was performed via extensive mathematical modeling of a theoretical restraint system. First, math models (correlated with several existing physical tests) were used to predict the occupant responses associated with 336 different theoretical dual-stage driver airbag designs subjected to six specific Regulated and non-Regulated tests.

The Vehicle Handling Model (VHM) is representative of a new type of vehicle dynamics programs which can be easily used on a personal computer by vehicle development engineers. It consists of a simulation kernel which solves the vehicle equations of motion and a hypertext GUI which controls the model data input, execution, and post processing. The vehicle model has 5 DOF, including the vehicle lateral, vertical, yaw, pitch, and roll motions. The simulation also includes suspension compliance, a simple non-linear tire model, a wind gust model and a human driver model to provide realistic vehicle and steering inputs. The simulation program was generated by AUTOSIM which uses a high level description of the system to generate Fortran source code. The GUI allows an engineer to setup the model, run the analysis, and display the results with just a few clicks of the mouse.

Predicting the service lifetime of elastomeric automotive components is key to improving customer satisfaction over a 10 year / 150,000 mile desired lifetime. Achieving a good correlation between artificially aged components and those which have seen real customer usage can be a daunting task, considering the possible variations in climate, exposure and driver aggressiveness. In natural rubber (NR) components, the quantity and structure of the network crosslinks as a function of time can be used to explore some of the most basic aging mechanisms seen in the real world, as well as to validate protocols developed within the laboratory environment to accelerate the simulation of real-world mechanisms. This paper explores the findings of such a study on an NR engine mount, and examines the information learned by comparison between actual used components and test specimens subjected to accelerated degradation.

The salt spray test has been an industry wide standard corrosion test since its conception in 1914. A literary review of its history shows that it has· always been thought of as inconsistent and unreliable but, for a variety of reasons, has continued to be used. A study of more than 55 salt spray cabinets was performed using a controlled lot of parts and questionnaires on cabinet operation. Although the tested parts varied from mildly corroded to extremely rusted no factor could be found to account for the differences. Although the test has its uses it should be studied by an industry formed committee which should make recommendations as to further standardization and corrections to the test. A lengthy chronological bibliography aids the reader in further study and reference.