Search Results

Engineers doing squeak and rattle testing of instrument panels (IP's) have successfully used large electrodynamic vibration systems to identify sources of squeaks and rattles (S&R's). Their successes led to demands to test more IP's, i.e., to increase throughput of IP's to reflect the many design, material, and/or manufacturing process changes that occur, and to do so at any stage of the development, production, or QA process. What is needed is a radically different and portable way to find S&R's in a fraction of the time and at lower capital cost without compromising S&R detection results.

This paper outlines the key elements in a laboratory reliability verification test program for an automotive sub-system. Many of these elements are described in some detail through the various stages of development from prototype concept to production. By means of an actual case study, verification testing of the 1970 Ford Anti-Theft Steering Column, steps required to design tests which yield meaningful information and the rationale used to analyze the results are presented. The steering column on a late model automobile is a complex system which combines several functions and features; steering, shifting, warning devices (turn signal and emergency flashers), ignition switch, anti-theft devices plus several safety features. The effectiveness of the overall verification program is evaluated through the presentation of actual field-feedback results.

A series of tests have been performed on a production vehicle to determine the characteristics of the external turbulent flow field in wind tunnel and road conditions. Empirical formulas are developed to use the measured data as source levels for a Statistical Energy Analysis (SEA) model of the vehicle structural and acoustical responses. Exterior turbulent flow and acoustical subsystems are used to receive power from the source excitations. This allows for both the magnitudes and wavelengths of the exterior excitations to be taken into account - a necessary condition for consistently accurate results. Comparisons of measured and calculated interior sound levels show good correlation.

Sound package engineering has always been an art developed through experience and much subjective road testing. Because the problem is complex, it is essential to have a logical procedure to achieve the most efficient sound package. The quiet car concept is proposed as a solution. Additionally, a plea is made for relevant automobile-oriented material test procedures to be recognized industry-wide.

This paper explores the extent to which standard dilution tunnel measurements of motor vehicle exhaust particulate matter modify particle number and size. Steady state size distributions made directly at the tailpipe, using an ejector pump, are compared to dilution tunnel measurements for three configurations of transfer hose used to transport exhaust from the vehicle tailpipe to the dilution tunnel. For gasoline vehicles run at a steady 50 - 70 mph, ejector pump and dilution tunnel measurements give consistent results of particle size and number when using an uninsulated stainless steel transfer hose. Both methods show particles in the 10 - 100 nm range at tailpipe concentrations of the order of 104 particles/cm3.

Due to several indeterminate factors, the assessment of the durability performance of a vehicle body is traditionally accomplished using test methods. An analytical fatigue life prediction method (four-step durability process) that relies mainly on numerical techniques is described in this paper. The four steps comprising this process include the identification of high stress regions, recognizing the critical load types, determining the critical road events and calculation of fatigue life. In addition to utilizing a general purpose finite element analysis software for the application of the Inertia Relief technique and a previously developed fatigue analysis program, two customized programs have been developed to streamline the process into an integrated, user-friendly tool. The process is demonstrated using a full body, finite element model.

Liquid fuels and the fuel vapors in equilibrium with them typically differ in composition. These differences impact automotive fuel systems in several ways. Large compositional differences between liquid and vapor phases affect the composition of species taken up within the evaporative emission control canister, since the canister typically operates far from saturation and doesn't reach equilibrium with the fuel tank. Here we discuss how these differences may be used to diagnose the mode of emission from a sealed container, e.g., a fuel tank. Liquid or vapor leaks lead to particular compositions (reported here) that depend on the fuel components but are independent of the container material. Permeation leads to emissions whose composition depends on the container material. If information on the relative permeation rates of the different fuel components is available, the results given here provide a tool to decide whether leakage or permeation is the dominant mode of emission.

A survey of industrial control computer applications presently operational in this user's facilities revealed an approximate 50/50 division between those that were internally and externally implemented. Problems encountered in the planning, launching, and follow-up phase of system installation were found to be common to both internal and external system implementations and are categorized and evaluated as being inherent and environmental in nature. In an effort to avoid anticipated problems characteristic of a computerized installation, proper staffing as an inhouse project team is essential. During the process of developing inhouse talent, three plateaus of system implementation maturity are attained. These plateaus range from complete dependency upon outside assistance to “do it yourself” inhouse implementation. Flow charts are developed to depict typical decision paths leading to a plateau of system implementation most appropriate for the particular user “turnkey dilemma.”

During frontal and rear end type collisions, very large forces will be imparted to the passenger compartment by the collapse of either front or rear structures. NCAP tests conducted by NHTSA involve, among other things, a door openability test after barrier impact. This means that the plastic/irreversible deformations of door openings should be kept to a minimum. Thus, the structural members constituting the door opening must operate during frontal and rear impact near the elastic limit of the material. Increasing the size of a structural member, provided the packaging considerations permit it, may prove to be counter productive, since it may lead to premature local buckling and possible collapse of the member. With the current trend towards lighter vehicles, recourse to heavier gages is also counterproductive and therefore a determination of an optimum compartment structure may require a number of design iterations. In this article, FEA is used to simulate front side door behavior.

In nowadays market, highlighted by global products, companies are pushed to sell products that comply with legal and customer requirements in different countries and, not unusually, different continents. In order to achieve such challenge, and pressed to reduce project and production costs, companies are spreading design centers around the world, based on regional expertise. These excellence centers must work together to benefit from synergies and local skills from different regions. Such projects are staffed by Virtual Team (BINDER, 2007), whose members barely face each other. This means teams will work frequently with people they have never met, who live on different time zones and have different cultures. As a consequence, communication is done basically through computer-based media, mainly based on emailing, and must be even clearer and more direct than with the people who work on the next desk.

Because it is common to attach plastic parts to other plastic, metal, or ceramic assemblies with mechanical fasteners that are often stronger and stiffer than the plastic with which they are mated, it is important to be able to predict the retention of the fastener in the polymeric component. The ability to predict this information allows engineers to more accurately estimate length of part service life. A study was initiated to understand the behavior of threaded fasteners in bosses molded from engineering thermoplastic resins. The study examined fastening dynamics during and after insertion of the fastener and the effects of friction on the subsequent performance of the resin. Tests were conducted at ambient temperatures over a range of torques and loads using several fixtures that were specially designed for the study. Materials evaluated include modified-polyphenylene ether (M-PPE), polyetherimide (PEI), polybutylene terephthalate (PBT), and polycarbonate (PC).

In 1998, the United States Field Trial was chartered by the United States Council for Automotive Research/Vehicle Recycling Partnership with the objective of evaluating the feasibility of collecting and recycling automotive polymers from domestic end-of-life Vehicles (ELVs). Although ELVs are among the most widely recycled consumer products, 15-25% of their total mass must nevertheless be disposed of with no material recovery; the majority of this remainder is polymeric. Concerns regarding vehicle abandonment risks and disposal practices have resulted in the legislated treatment of ELVs in Western Europe, and in the emergence of attendant material recycling schemes. These schemes support quantitatively optimized material collection, but do not appear to be sustainable under the free-market economic conditions prevalent in North America.

This report is a comprehensive investigation into the use of resin transfer molded glass fiber reinforced plastics in a structural application. A pickup truck cab structure is an ideal application for plastic composites. The cab is designed to fit a production Ranger pickup truck and uses carryover frame and front end structure. The cab concept consists primarily of two molded pieces. This design demonstrates extensive parts integration and allows for low-cost tooling, along with automated assembly.

Present models and methods for simulations of sheet metal forming processes are reviewed in this paper. Because of rapid progress of computer hardware, complex computations, formerly impossible to perform due to high computational cost, are now feasible. Therefore, more realistic and computational intensive models are suggested for finite elements, materials, and frictional forces. Also, simulation methods suitable for sheet metal forming processes are recommended. Four numerical examples at the end of the paper are presented to support the recommendations.

Aftertreatment system design involves multiple tradeoffs between engine performance, fuel economy, regulatory emission levels, packaging, and cost. Selection of the best design solution (or “architecture”) is often based on an assumption that inherent catalyst activity is unaffected by location within the system. However, this study acknowledges that catalyst activity can be significantly impacted by location in the system as a result of varying thermal exposure, and this in turn can impact the selection of an optimum system architecture. Vehicle experiments with catalysts aged over a range of mild to moderate to severe thermal conditions that accurately reflect select locations on a vehicle were conducted on a chassis dynamometer. The vehicle test data indicated CO and NOx could be minimized with a catalyst placed in an intermediate location.

The paper briefly reviews the current and future needs for automotive electronic packaging technology and the related reliability issues. Reliability approaches based upon physics-of-failure are discussed, and an example is given to illustrate the importance of understanding the root cause of failure and the application of a state-of-the-art approach to life prediction of leadless solder joints under thermal cycling. An introduction is also given to the recent development of the CAIR (Computer Aided Interconnect Reliability) system developed at Ford for reliability prediction of solder interconnects in automotive electronic packaging. The system integrates a number of software modules using a user interface and allows for evaluation of critical design parameters within a short period of time. The system is intended to implement the “prevention mode” into the product design process to meet the increasing reliability demand and to reduce cost and cycle time.

A framework for considering trade-offs between increased costs for lightweight materials and the attendant fuel savings accruing from weight reduction is developed in this paper. Two quantitative estimates of lifetime fuel savings due to weight reduction of a vehicle are derived. For substitution on an ongoing vehicle, available data suggest savings of about 0.26 gallons for the vehicle lifetime per lb. of weight reduction. When long-term changes in vehicles follow lightweight material feasibility, a range of estimates must be quoted; viz: 0.55 to 1.07 gallons for the vehicle life per primary pound saved. Considerations of trading these fuel savings against higher costs highlights two crucial issues: (1) the percentage weight reduction achieved in the substitution and (2) fabrication cost penalties. These technical issues largely determine whether a given application saves over-all resources.

Measurements of oxygen storage capacity (OSC) and HC conversion efficiency for 17 catalysts were carried out in the laboratory. All catalysts with steady state HC efficiency below 90% were found to have roughly equivalent and very low capacities to store oxygen. However, catalyst oxygen storage capacity was seen to rise sharply with HC conversion efficiency in excess of 90 percent. These results parallel the trends which are observed between rear HEGO/EGO indexes for OBD-II catalyst monitoring and HC conversion efficiency. In addition, temperature programed reduction (TPR) was found to lend insight into the relationship between catalyst OSC and HC conversion efficiency by providing a qualitative understanding of the mechanisms by which OSC deteriorates. TPR profiles showed that most of the usable oxygen storage is derived from surface ceria which is interacted with precious metals.

The P2000S body structure was designed as part of an advanced research project to determine the feasibility of a high volume, lightweight sport utility vehicle (SUV) that would achieve performance targets of the newly emerging “City SUV” market by developing a unitized (no frame) SUV body structure fabricated principally of aluminum. In order to be viable, this body structure was required to meet all safety, durability, NVH and other functional attributes of a truck while having the ride characteristics of a sedan. This paper describes the P2000S body structure including the structural philosophy, project constraints on the design, manufacturing processes, supporting analyses, assembly processes and unique material and design concepts which resulted in the 50% body structure weight reduction in comparison to similar sized body-on-frame production steel sport utility vehicles.

Splash and spray conditions created by tractor-trailer combinations operating on the Federal highway system have been studied and tested for many years with mixed results. Past events are reviewed briefly in this paper. In additional testing during 1983, using new state-of- the-art splash/spray suppressant devices, some encouragement was provided that these devices could work. The 1984 Motor Vehicle Manufacturers Association (MVMA) test program was designed to develop practicable and reliable test procedures to measure effectiveness of splash and spray reduction methods applied to tractor-trailer combination vehicles. Over 40 different combinations of splash/spray suppression devices on five different tractors and three van trailer types were tested. The spray-cloud densities for some 400 test runs were measured by laser transmissometers and also recorded by still photography, motion pictures, and videotape. On-site observers made subjective ratings of spray density.