Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Wind Noise Spectral Predictions Using a Lattice-Based Method

1999-05-17
1999-01-1810
The current ability of the Virtual Aerodynamic/ Aeroacoustic Wind Tunnel to predict interior vehicle sound pressure levels is demonstrated using an automobile model which has variable windshield angles. This prediction method uses time-averaged flow solutions from a lattice gas CFD code coupled with wave number-frequency spectra for the various flow regimes to calculate the side window vibration from which the sound pressure level spectrum at the driver's ear is determined. These predictions are compared to experimental wind tunnel data. The results demonstrate the ability of this methodology to correctly predict wind noise spectral trends as well as the overall loudness at the driver's ear. A more sophisticated simulation method employing the same lattice gas code is investigated for prediction of the time-accurate flow field necessary to compute the actual side glass pressure spectra.
Technical Paper

Virtual Engine Dynamometer in Service Life Testing of Transmissions: A Comparison Between Real Engine and Electric Dynamometers as Prime Movers in Validation Test Rigs

2010-04-12
2010-01-0919
A test cell was developed for evaluating a 6-speed automatic transmission. The target vehicle had an internal combustion 5.4L gasoline V8 engine. An electric dynamometer was used to closely simulate the engine characteristics. This included generating mean torque from the ECU engine map, with a transient capability of 10,000 rpm/second. Engine inertia was simulated with a transient capability of 20,000 rpm/second, and torque pulsation was simulated individually for each piston, with a transient capability of 50,000 rpm/second. Quantitative results are presented for the correlation between the engine driven and the dynamometer driven transmission performance over more than 60 test cycles. Concerns about using the virtual engine in validation testing are discussed, and related to the high frequency transient performance required from the electric dynamometer. Qualitative differences between the fueled engine and electric driven testing are presented.
Technical Paper

Vehicle Wind Noise Analysis Using a SEA Model with Measured Source Levels

2001-04-30
2001-01-1629
A series of tests have been performed on a production vehicle to determine the characteristics of the external turbulent flow field in wind tunnel and road conditions. Empirical formulas are developed to use the measured data as source levels for a Statistical Energy Analysis (SEA) model of the vehicle structural and acoustical responses. Exterior turbulent flow and acoustical subsystems are used to receive power from the source excitations. This allows for both the magnitudes and wavelengths of the exterior excitations to be taken into account - a necessary condition for consistently accurate results. Comparisons of measured and calculated interior sound levels show good correlation.
Technical Paper

Vehicle Sound Package - Art or Science?

1972-02-01
720508
Sound package engineering has always been an art developed through experience and much subjective road testing. Because the problem is complex, it is essential to have a logical procedure to achieve the most efficient sound package. The quiet car concept is proposed as a solution. Additionally, a plea is made for relevant automobile-oriented material test procedures to be recognized industry-wide.
Technical Paper

Vehicle Flow Measurement and CFD Analysis for Wind Noise Assessment

1997-02-24
970403
A time cost effective methodology has been developed for the prediction of the A-pillar vortex formation and the side and the rear window flow separation for the purpose of wind noise assessment. This methodology combines a simplified Computational Fluid Dynamics (CFD) model and wind tunnel test data by CFD post-processing tools. The solution of the simplified CFD model provides background data for the whole flow field, but it lacks detail features such as mirror, sealing groove and glass in-set, which are locally important but difficult to mesh and require a very fine mesh resolution. The wind tunnel test data was taken in the specific areas of interest at the A-pillar, side window, rear window area, and roof from a real automotive. Then the wind tunnel test data was superposed upon the simplified CFD model to correct the numerical error due to geometry simplification and insufficient mesh resolution.
Technical Paper

Vehicle Body Structure Durability Analysis

1995-04-01
951096
Due to several indeterminate factors, the assessment of the durability performance of a vehicle body is traditionally accomplished using test methods. An analytical fatigue life prediction method (four-step durability process) that relies mainly on numerical techniques is described in this paper. The four steps comprising this process include the identification of high stress regions, recognizing the critical load types, determining the critical road events and calculation of fatigue life. In addition to utilizing a general purpose finite element analysis software for the application of the Inertia Relief technique and a previously developed fatigue analysis program, two customized programs have been developed to streamline the process into an integrated, user-friendly tool. The process is demonstrated using a full body, finite element model.
Technical Paper

Use of FCRASH in a Door Openability Simulation

1997-04-08
971526
During frontal and rear end type collisions, very large forces will be imparted to the passenger compartment by the collapse of either front or rear structures. NCAP tests conducted by NHTSA involve, among other things, a door openability test after barrier impact. This means that the plastic/irreversible deformations of door openings should be kept to a minimum. Thus, the structural members constituting the door opening must operate during frontal and rear impact near the elastic limit of the material. Increasing the size of a structural member, provided the packaging considerations permit it, may prove to be counter productive, since it may lead to premature local buckling and possible collapse of the member. With the current trend towards lighter vehicles, recourse to heavier gages is also counterproductive and therefore a determination of an optimum compartment structure may require a number of design iterations. In this article, FEA is used to simulate front side door behavior.
Technical Paper

Ultra Thin Wall Substrates - Trends for Performance in FTP and US06 Tests

2002-03-04
2002-01-0356
This paper compares the emissions performance of four ultra thin wall ceramic substrates with standard wall thickness product on a chassis dynamometer for two different substrate volumes. This comparison helps establish performance trends and provides useful information for selection of substrates in designing catalytic converter systems. This experimental study tests and compares four ultra thin wall products (400/4, 600/3, 600/4, and 900/2) with a standard wall product (400/6.5) at two different substrate volumes. Engine bench aging is used to simulate typical aged conditions. Temperature data as well as second by second and bag emissions data for hydrocarbons, carbon monoxide and oxides of nitrogen were used to evaluate the relative performances of the substrates. The US FTP and US06 driving cycles were used as protocols for the comparison. Results suggest that lower bulk density and higher geometric surface area interact to lead to lower emissions.
Technical Paper

Tire Treadwear Experiment Using Taguchi Methods

1988-02-01
880580
An experiment has been conducted to study the effect of vehicle alignment, tire construction and operational conditions on tire treadwear. The Taguchi approach was used to compose the experimental design and to analyze the data. The treadwear testing was conducted on the indoor test machine; this test duplicates the treadwear pattern observed during road test. The responses of interest were total wear, irregular wear patterns, and diagonal wear. The study quantified the relative importance of different factors to treadwear and also the degree of wear irregularity.
Technical Paper

The Mvma Investigation Into the Complexities of Heavy Truck Splash and Spray Problem

1985-01-01
856097
Splash and spray conditions created by tractor-trailer combinations operating on the Federal highway system have been studied and tested for many years with mixed results. Past events are reviewed briefly in this paper. In additional testing during 1983, using new state-of- the-art splash/spray suppressant devices, some encouragement was provided that these devices could work. The 1984 Motor Vehicle Manufacturers Association (MVMA) test program was designed to develop practicable and reliable test procedures to measure effectiveness of splash and spray reduction methods applied to tractor-trailer combination vehicles. Over 40 different combinations of splash/spray suppression devices on five different tractors and three van trailer types were tested. The spray-cloud densities for some 400 test runs were measured by laser transmissometers and also recorded by still photography, motion pictures, and videotape. On-site observers made subjective ratings of spray density.
Technical Paper

The Influence of Test Site on Exterior Vehicle Noise Measurements

1974-02-01
740967
As the compliance with noise legislation became more difficult, Ford exhaust system development engineers increasingly encountered variances not only from vehicle-to-vehicle, but on the same vehicle tested in different locations. As a result, a series of tests were conducted to establish the correlation among various sites for vehicle exterior noise measurements. The purpose of this paper is to present the results and the method developed to achieve the correlation in terms of the following: 1. Ford and site equipment differences 2. Driver differences 3. Differences between site physical qualities Seven sites were evaluated in the program where seven vehicles were used with a good spread in exterior noise levels. A representative correlation plot is also presented which can be used to predict the expected noise level of any vehicle at any one of these test sites knowing the level obtained at the Ford site.
Technical Paper

The Influence of Heat Treat Process and Alloy on the Surface Microstructure and Fatigue Strength of Carburized Alloy Steel

1999-03-01
1999-01-0600
Gas carburized and quenched low alloy steels typically produce surface microstructures which contain martensite, retained austenite and often NMTP's (non-martensitic transformation products). The NMTP's are caused by a reduction of surface hardenability in the carburizing process from loss of alloying elements to oxidation. Gas carburized low alloy steels such as SAE 8620 with NMTP's on the surface have been shown to have inferior bending fatigue properties when compared to more highly alloyed steels which do not form NMTP's, such as SAE 4615M. One method of minimizing the formation of oxides and eliminating NMTP formation during carburizing and quenching is to use plasma carburizing instead of conventional gas carburizing. In this study the microstructures and bending fatigue performance of plasma carburized SAE 8620 and SAE 4615M is compared to the same alloys conventionally gas carburized and quenched.
Technical Paper

The Fourier Transform Applied to Vehicle Exterior Noise Source Identification

1976-02-01
760151
This paper discusses a motor vehicle noise source identification technique designed for use during the SAE J986a or similar drive-by test procedure. It provides, by application of the Fourier Transform, the capability to obtain a narrowband (9.8 Hz) frequency resolution over an extended frequency range (0-10,000 Hz) at the peak vehicle noise level, a particular RPM, or a particular vehicle location in the test zone. Other features include corrections for the Doppler shift, averaging of noise tests, and subtraction of spectra of two separate noise tests from a component disconnect/reconnect procedure. The above analysis, in conjunction with the noise source isolation resulting directly from the disconnect procedure, identifies the major vehicle noise contributors in terms of their respective amplitudes and frequencies.
Technical Paper

The Ford GT Transaxle - Tailor Made in 2 Years

2004-03-08
2004-01-1260
This paper describes the rapid development of the Ford GT transmission, from concept phase to production, where the technical challenges involved are implicit in the specifications provided. It presents the steps taken at a project management level to expedite development, as well as the tools used to design and rate components at the design stage. Examples of concurrent engineering are given as well as management techniques used to predict and address key risks. In addition, details of analysis and test procedures are given, underlining their contribution to the rapid introduction of the transmission to the market place.
Technical Paper

The Ford Aluminum Beaker Test: A New Tool for the Study of ATF Oxidation

1967-02-01
670023
A small-scale oxidation test for automatic transmission fluids has been developed. In the test air flow rates, temperature and catalytic activity can be closely controlled at desired levels. A test procedure for screening automatic transmission fluids is described. Data are presented illustrating the ability of the test to distinguish between different levels of oxidation resistance, the repeatability of the test, and the correlation achieved thus far with a presently used full-scale transmission oxidation test.
Technical Paper

The First Standard Automotive Crash Dummy

1969-02-01
690218
The SAE Recommended Practice J963 “Anthropomorphic Test Device for Dynamic Testing” describes a standard 50th percentile adult male anthropomorphic test dummy. For nearly three years the Crash Test Dummy Task Force worked with the limited data available in selecting values for the body dimensions and ranges of motion. The data for specifying the values of mass distribution were developed experimentally as was a test procedure for determining the dynamic spring rate of the thorax.
Technical Paper

The Effect of Exhaust Gas Recirculation on Soot Formation in a High-Speed Direct-injection Diesel Engine

1996-02-01
960841
A number of tests were conducted on a 2.5 litre, high-speed, direct-injection diesel engine running at various loads and speeds. The aim of the tests was to gain understanding which would lead to more effective use of exhaust gas recirculation (EGR) for controlling exhaust NOx whilst minimising the penalties of increased smoke emission and fuel consumption. In addition to exhaust emission measurements, in-cylinder sampling of combustion gases was carried out using a fast-acting, snatch-sampling valve. The results showed that the effectiveness of EGR was enhanced considerably by cooling the EGR. In addition to more effective NOx control, this measure also improved volumetric efficiency which assisted in the control of smoke emission and fuel consumption. This second of two papers on the use of EGR in diesel engines deals with the effects of EGR on soot emission and on the engine fuel economy.
Technical Paper

The Effect of Copper Level and Solidification Rate on the Aging Behavior of a 319-Type Cast Aluminum Alloy

2000-03-06
2000-01-0759
Compositional and microstructural variations in a casting can often result in rather significant variations in the response to a given aging treatment, leading to location dependent mechanical properties. The objective of this study is to determine the effect of copper content and solidification rate on the aging behavior of a type 319 cast aluminum alloy. The nominal composition of the alloy is Al-7% Si-3.5% Cu-0.25% Mg, however, typical secondary 319 aluminum specifications allow copper levels to vary from 3-4%. Solidification rates throughout a casting can vary greatly due to, among other factors, differences in section size. To determine the effect of copper level and solidification rate on the aging response, aging curves were experimentally developed for this alloy. Three different copper levels (3, 3.5, 4%) and two solidification rates were used for this study. Aging temperatures ranged from 150-290°C with nine aging times at each temperature.
Technical Paper

The Aerodynamic Development of the 1986 European Ford Transit

1987-02-01
870247
THIS PAPER GIVES an overview of the aerodynamic development of a medium commercial vehicle. It deals with the setting out and achievement of the objectives of reducing aerodynamic drag as well as other aspects of aerodynamic design development such as engine cooling, heating and ventilating and sensitivity to side winds. Reference is made to measures taken to develop heater intake designs which are suitable for a low resistance vehicle with a fast attached flow over most of the forward surfaces. At the time of initial design studies, the Ford of Europe windtunnel in Cologne, West Germany, had not yet been commissioned and it was necessary therefore to adapt testing methods to suite the different windtunnels which were used at various stages of the development programme.
Technical Paper

THE APPLICATIONS OF RADIOACTIVITY FOR THE CONTROL AND TESTING OF AUTOMOTIVE MATERIALS

1957-01-01
570035
APPLICATIONS of nuclear energy in automotive manufacture have been made principally in the field of radioactivity. These are grouped under the following categories: radiography, nondestructive testing, gaging and control, tracer techniques, and static neutralizers. Radioactivity techniques are being used in foundry operations to check stock and metal levels in cupolas and distribution of element additives. In steel operations, these techniques are being used to check assimilation of ore-concentrate fines and thickness of rolled sheet steel. Other applications include measurement of pipe and wall thickness in pressure lines and engines, and inspection of castings and welds for internal faults. Radioactive techniques for improving processes, quality, and materials have potentially universal application. Greater industrial access to reactors will permit broader study and speed the development of new applications of radio-activity in industry.
X