Search Results

Metal cutting/machining is a widely used manufacturing process for producing high-precision parts at a low cost and with high throughput. In the automotive industry, engine components such as cylinder heads or engine blocks are all manufactured using such processes. Despite its cost benefits, manufacturers often face the problem of machining chips and cutting oil residue remaining on the finished surface or falling into the internal cavities after machining operations, and these wastes can be very difficult to clean. While part cleaning/washing equipment suppliers often claim that their washers have superior performance, determining the washing efficiency is challenging without means to visualize the water flow. In this paper, a virtual engineering methodology using particle-based CFD is developed to address the issue of metal chip cleanliness resulting from engine component machining operations. This methodology comprises two simulation methods.

A vehicle integrated sensing and analysis system has been designed, implemented, and demonstrated to nonintrusively monitor several biological signals of the driver. The biological driver signals measured by the system are the heart electrical signals or pseudo Lead-I electrocardiography (pLI-ECG), the galvanic skin response (GSR) or electrical conductance measured from the driver's fingers to palm, the palm skin temperature, the face skin temperature, and the respiration rate. The pLI-ECG and GSR measurements are made through direct contact of the driver hands with stainless steel electrodes integrated in the steering wheel rim. The temperature measurements are made with non-contacting infrared temperature sensors, also located on the steering wheel. The respiration rate was measured using a flexible thin film piezoelectric sensor affixed to the seatbelt.

For many years, the use of in-mold fasteners has been avoided for various reasons including: not fully understanding the load cases in the part, the fear of quality issues occurring, the need for servicing, or the lack of understanding the complexity of all failure modes. The most common solution has been the use of secondary operations to provide attachments, such as, screws, metal clips, heat staking, sonic welding or other methods which are ultimately a waste in the process and an increase in manufacturing costs. The purpose of this paper is to take the reader through the design process followed to design an in-molded attachment clip on plastic parts. The paper explores the design process for in-molded attachment clips beginning with a design concept idea, followed by basic concept testing using a desktop 3D printer, optimizing the design with physical tests and CAE analysis, and finally producing high resolution 3D prototypes for validation and tuning.

Squeak and rattle is one of the major concerns in vehicle design for customer satisfaction. Traditionally squeak and rattle problems are found and fixed at a very late design stage due to lack of up-front CAE prevention and prediction tools. A research work at Ford reveals a correlation between the squeak and rattle performance and diagonal distortions at body closure openings and fastener accelerations in an instrument panel. These findings make it possible to assess squeak and rattle performance implications between different body designs using body-in-prime (B-I-P) and vehicle low frequency noise, vibration and harshness (NVH) CAE models at a very early design stage. This paper is concerned with applications of this squeak and rattle assessment method for up-front body designs prior to a prototype stage.

The previously developed power-based fuel consumption theory for Internal Combustion Engine Vehicles (ICEV) is extended to Battery Electric Vehicles (BEV). The main difference between the BEV model structure and the ICEV is the bi-directional character of traction motors and batteries. A traction motor model was developed as a bi-linear function of positive and negative traction power. Another difference is that the accessories and cabin heating are powered directly from the battery, and not from the powertrain. The resulting unified model for ICEV and BEV energy consumption has linear terms proportional to positive and negative traction power, accessory power, and overhead, in varying proportions. Compared to the ICEV, the BEV powertrain has a high marginal efficiency and low overhead. As a result, BEV energy consumption data under a wide range of driving conditions are mainly proportional to net traction power, with only a small offset.

Advanced features in automotive systems often necessitate the management of complex interactions between subsystems. Existing control strategies are designed for certain levels of robustness, however their performance can unexpectedly deteriorate in the presence of significant uncertainties, resulting in undesirable system behaviors. This limitation is further amplified in systems with complex nonlinear dynamics. Hydro-mechanical clutch actuators are among those systems whose behaviors are highly sensitive to variations in subsystem characteristics and operating environments. In a P2 hybrid propulsion system, a wet clutch is utilized for cranking the engine during an EV-HEV mode switching event. It is critical that the hydro-mechanical clutch actuator is stroked as quickly and as consistently as possible despite the existence of uncertainties. Thus, the quantification of uncertainties on clutch actuator behaviors is important for enabling smooth EV-HEV transitions.

This paper presents a Short Time Fourier Transform based algorithm to identify unknown parameters in fuel dynamics system during engine cold start and warm-up. A first order system is used to model the fuel dynamics in a port fuel injection engine. The feed forward transient fuel compensation controller is designed based on the identified model. Experiments are designed and implemented to verify the proposed algorithm. Different experiment settings are compared.

Direct bypass to DC-DC boost converter in traction inverter increases converter's capability and efficiency significantly by providing a lower loss path for power flow between the battery and DC-link terminal. A bypass using diode is an excellent solution to achieve this capability at low cost and system complexity. Bypass diode operates in the linear operating region (DC Q-point) when the battery discharges through the bypass diode to drive the electric motors. Therefore, thermal stress on the DC-link capacitor is shared between the input and DC-link capacitors through the bypass diode. On the other hand, inverters introduce voltage oscillation in the DC-link terminal which results in unwanted energy oscillation through the bypass diode during battery charging. Both of these phenomena have been explained in details.

Bolted joint separation occurs when components of a joint are no longer capable of maintaining a clamp load. The clamp load of a joint is the resultant of various factors such as the strength of joining components, geometry, and the surface condition of the joined parts. The fastener installation torque is a very critical parameter that contributes towards achieving the desired clamping force at the joint during the assembly process. Thread rolling screws are increasingly being used in many automotive structural applications. The thread rolling screws are easy to install, are self aligning, and offer a torque prevailing feature with improved vibration resistance when mated with a un-threaded nut. This combination results in a robust joint and low field costs. They also offer increased joint strength by work hardening the mating nut interface.

The measured drive-point conductance of a typical passenger car tire was seen to drop steadily for frequencies above 1000 Hz. This behavior is a-typical since SEA theory predicts such conductance should remain relatively flat for high frequencies. It was found that, one has to pay careful attention to errors introduced by the added mass of the measuring transducer and “local” effects due to contact stiffness of the tread rubber. Such effects are investigated and their contributions quantified. Compensation schemes are also developed and implemented. It is shown that, for a 20 grams transducer, the measured and corrected conductances are off by 12 dB. The effects of the local contact stiffness of the rubber at the attachment point are less significant.

Automobile customers are looking for higher performance and quieter comfortable rides. The driveline of a vehicle can be a substantial source of NVH issues. This paper provides an understanding of a driveline noise issue which can affect any variant of driveline architecture (FWD, AWD, RWD and 4X4). This metallic noise is mostly present during the take-off and appropriately termed as ting noise. This noise was not prevalent in the past. For higher fuel economy, OEMs started integrating several components for lighter subsystems. This in effect made the system more sensitive to the excitation. At present the issue is addressed by adding a ting washer in the interface of the wheel hub bearings and the halfshafts. This paper explains the physics behind the excitation and defines the parameters that influence the excitation. The halfshaft and the wheel hub are assembled with a specified hub nut torque.

Thermally sprayed coatings have used in place of iron bore liners in recent aluminum engine blocks. The coatings are steel-based, and are sprayed on the bore wall in the liquid phase. The thermal response of the block structure determines how rapidly coatings can be applied and thus the investment and floor space required for the operation. It is critical not to overheat the block to prevent dimensional errors, metallurgical damage, and thermal stress cracks. This paper describes an innovative finite element procedure for estimating both the substrate temperature and residual stresses in the coating for the thermal spray process. Thin layers of metal at a specified temperature, corresponding to the layers deposited in successive thermal spray torch passes, are applied to the substrate model, generating a heat flux into the block. The thickness, temperature, and application speed of the layers can be varied to simulate different coating cycles.

The use of nanotechnology to develop advanced heat-transfer materials is a rapidly growing topic of research at facilities around the world. One class of these materials, nanofluids, has shown promise in the laboratory to dramatically improve thermal conductivity. Quantification of the thermophysical properties of these fluids is important for optimizing the design of automotive powertrains and electrical subsystems in order to produce highly efficient and robust vehicle cooling. A new technique for measuring thermal conductivity, the Transient Planar Source (TPS) method, was used for the first time to investigate the thermal conductivity of automotive coolants and their equivalent nanofluid, as a function of temperature. The results of this study indicate that the TPS method allows for rapid and repeatable measurement of thermal conductivity with an error of between 2-4%. The technique also presents several advantages over other methods which we will briefly describe.

Over the past five years, the US Automotive Materials Partnership (USAMP) has brought together representatives from DaimlerChrysler, General Motors, Ford Motor Company and over 40 other participant companies from the Mg casting industry to create and test a low-cost, Mg-alloy engine that would achieve a 15 - 20 % Mg component weight savings with no compromise in performance or durability. The block, oil pan, and front cover were redesigned to take advantage of the properties of both high-pressure die cast (HPDC) and sand cast Mg creep- resistant alloys. This paper describes the alloy selection process and the casting and testing of these new Mg-variant components. This paper will also examine the lessons learned and implications of this pre-competitive technology for future applications.

The process parameters to manufacture structural aluminum alloys are critical to their ductility. In particular, quench rate after solution heat treatment impacts the extent of grain boundary precipitation and the formation of precipitate free zone (PFZ) during later artificial aging. Cu-containing 6XXX alloys used for high strength automotive applications are quench sensitive as the Cu addition leads to Q-phase precipitation at grain boundaries, resulting in loss of ductility, which can negatively affect downstream manufacturing steps such as automotive joining and forming processes. Self-piercing rivet (SPR) joining, is a single step, spot joining process used to mechanically connect sheet materials together in automotive body structures. Ductility has been identified as an important metric of material rivet-ability or the ability to make a successful, crack-free SPR joint.

Technical Standards are essential for the expanded use of any engineering material. The Society of Automotive Engineers (SAE) Iron and Steel Castings Committee has been reworking existing, (and issuing new), standards for automotive iron and steel castings. This paper will review the status of the SAE standards for Ductile Iron, Austempered Ductile Iron (ADI), Compacted Graphite Iron (CGI) and high Silicon-Molybdenum (Si-Mo) Ductile Iron, Gray Iron and Steel Castings. The SAE Standards, (and draft standards), will be critically compared to those for ASTM and ISO. Salient differences in the standards will be discussed and implications to design engineers will be addressed. Comparisons to other, competitive materials (and their standards) will be made.

During the last decade, advances in magnesium die casting technology have enabled the production of large lightweight thin walled die castings that offer new approaches for low investment body construction techniques. As a result, many OEMs have expressed an interest in magnesium door closure systems due to investment reduction opportunities, coupled with potential weight savings of up to 50%. However, for such applications, product engineers are faced with the challenge of designing for stiffness and strength in crash critical applications with a material of lower modulus and ductility compared to wrought sheet product. Concept designs for side door systems have been presented in the literature, and indicate that structural performance targets can be achieved. However, to date, series production designs feature a multitude of supplementary sheet metal reinforcements, attached to die castings, to handle structural loads.

The lack of electrical conductivity on materials, which are used in automotive fuel systems, can lead to electrostatic charges buildup in the components of such systems. This accumulation of energy can reach levels that exceed their capacity to withstand voltage surges, which considerably increases the risk of electrical discharges or sparks. Another important factor to consider is the conductivity of the commercially available fuels, such as biodiesel, which contributes to dissipate these charges to a proper grounding point in automobiles. From 2013, the diesel regulation in Brazil have changed and the levels of sulfur in the composition of diesel were reduced considerably, changing its natural characteristic of promoting electrostatic discharges, becoming more insulating.

In this paper, the high-temperature capability of the traction inverter was investigated by applying coolant with temperature much higher than the typical allowed value until the system fails. The purpose of this study is to identify the weakest link of the traction inverter system in terms of temperature. This study was divided into two stages. In the first stage, a series of nondestructive tests were carried out to investigate temperature rise (ΔT) of the key component above coolant temperature as a function of the outside controllable parameters-i.e., dc link voltage, phase current, and switching frequency. The key components include power modules, gate driver board, gate driver power supply, current sensors and dc link capacitor. Their temperatures were monitored by thermocouples or on-die temperature sensors.

This paper will discuss the vehicle top-down design approach that includes the non-linearity and sub-system interactions such as tire and road, (left and right) interaction between two or more parts connected by bushings, springs, bolts, stabilizer-bar, etc… The proposed method would allow for the inclusion of realistic boundary conditions and proper load simulation, and it would provide the ability to visualize and evaluate dynamic structural phenomena and complex component interaction. This approach would also facilitate the evaluation of design changes that may affect load propagation and/or load magnitude. All of the advantages of the sub-system analysis method mentioned above would allow for a greater understanding of the sub-system as a whole and help correctly identify the design requirements needed for the individual components that make up such chassis subsystems.