Search Results

In general for Vehicle-to-Vehicle (V2V) communication, message authentication is performed on every received wireless message by conducting verification for a valid signature, and only messages that have been successfully verified are processed further. In V2V safety communication, there are a large number of vehicles and each vehicle transmits safety messages frequently; therefore the number of received messages per second would be large. Thus authentication of each and every received message, for example based on the IEEE 1609.2 standard, is computationally very expensive and can only be carried out with expensive dedicated cryptographic hardware. An interesting observation is that most of these routine safety messages do not result in driver warnings or control actions since we expect that the safety system would be designed to provide warnings or control actions only when the threat of collision is high.

Automotive structural components are exposed to high loads, impact situations and corrosion. In addition, there may be temperature excursions that introduce creep as well as reduced modulus (stiffness). These issues have limited the use of light metals in automotive structural applications primarily to aluminum alloys, and primarily to cast wheels and knuckles (only a few of which are forged), cast brake calipers, and cast control arms. This paper reports on research performed at Chongqing University, Chongqing China, under the auspices of General Motors engineering and directed by the first author, to develop a protocol that uses wrought magnesium in control arms. The goal was to produce a chassis part that could provide the same engineering function as current cast aluminum applications; and since magnesium is 33% less dense than aluminum, would be lighter.

OBD system requirements were first developed by the California Air Resources Board, the U.S. Environmental Protection Agency, and the European Commission. New OBD requirements should be as consistent as possible with existing requirements to maximize reliability and to minimize system complexity, proliferation of configurations, and consumer cost. New OBD requirements from around the world are briefly reviewed and most are consistent with the original U.S. and European requirements. Worldwide OBD requirements are being further harmonized under the United Nations, Economic Commission for Europe, World Forum for Harmonization of Vehicle Regulations (WP29). Presenter David H. Ferris, General Motors Company

This paper presents development work on the design and analysis of the windshield wiper system. Three design categories are presented: geometrical design, wiper module and motor kinetics, and snow block structural analysis method. A comprehensive structural analysis method is outlined to determine the wiper system capability for continuous operation under a snow blocked condition. By using this design and analysis method, a robust windshield wiper system will be achieved.

The initial presence and dynamic formation of internal voids in human body models have been subjects of discussion within the human body modeling community. The relevant physics of the human body are described and the importance of capturing this physics for modeling of internal organ interactions is demonstrated. Basic modeling concepts are discussed along with a proposal of simulation setups designed to verify model behavior in terms of volume and pressure between internal organs.

With the advent of vehicle manufacturer driven on-board charging systems for plug-in and extended range electric vehicles, such as the Chevrolet Volt, important considerations need to be comprehended in both the requirements specified as well as the test methodologies and setups for electromagnetic compatibility (EMC). Typical automotive EMC standards (such as the SAE J551 and SAE J1113 series) that cover 12 volt systems have existed for many years. Additionally, there has been some development in recent years for high voltage EMC for automotive applications. However, on-board charging for vehicles presents yet another challenge in adopting requirements that have typically been in the consumer industry realm and merging those with both the traditional 12 V based system requirements as well as high voltage based systems.

In July 2007, GM announced that it would produce the Chevy Volt, the first high-production volume electric vehicle with extended range capability, by 2010. In January 2009, General Motors announced that the Chevrolet Volt's lithium ion Battery Pack, capable of propelling the Chevy Volt on battery-supplied electric power for up to 40 miles, would be designed and assembled in-house. The T-shaped battery, a subset of the Voltec propulsion system, comprises 288 cells, weighs 190 kg, and is capable of supplying over 16 kWh of energy. Many technical challenges presented themselves to the team, including the liquid thermal management of the battery, the fast battery pack development timeline, and validation of an unproven high-speed assembly process. This paper will first present a general overview of the approach General Motors utilized to bring the various engineering organizations together to design, develop, and manufacture the Volt battery.

Cooled exhaust gas recirculation (EGR) is widely used in diesel engines to control engine-out NOx (oxides of nitrogen) emissions. A portion of the exhaust gases is re-circulated into the intake manifold of the engine after cooling it through a heat exchanger. EGR cooler heat exchangers, however, tend to lose efficiency and have increased pressure drop as deposit forms on the heat exchanger surface due to transport of soot particles and condensing species to the cooler walls. In this study, condensation of water vapor and hydrocarbons at the exit of the EGR cooler was visualized using a fiberscope coupled to a camera equipped with a complementary metal oxide semiconductor (CMOS) color sensor. A multi-cylinder diesel engine was used to produce a range of engine-out hydrocarbon concentrations. Both surface and bulk gas condensation were observed with the visualization setup over a range of EGR cooler coolant temperatures.

Measured vehicle loads have traditionally been used as the basis for development of component, subsystem and vehicle level durability tests. The use of measured loads posed challenges due to the availability of representative hardware, scheduling, and other factors. In addition, stress was placed on existing procedures and methods by aggressive product development timing, variety in tuning and equipment packages, and higher levels of design optimization. To meet these challenges, General Motors developed new processes and technical competencies which enabled the direct substitution of analytically synthesized loads for measured data. This process of Virtual Road Load Data Acquisition (vRLDA) enabled (a) conformance to shortened product development cycles, (b) greater consistency between design targets and validation requirements, and (c) more comprehensive data.

The twist axle has highly complicated load paths because of its multiple functions of suspension components. This nature of the twist axle suspension makes the fixed reacted multi-axial suspension test more sophisticated than for other independent suspensions. GM has used Virtual Road Load Data Acquisition (vRLDA) for laboratory tests in the past, but this is the first application of vRLDA for a twist axle multi-axial suspension durability test. In order to utilize vRLDA data for the test input, a new approach to 8 channel multi-axial suspension durability test development was proposed for a twist axle rear suspension. vRLDA for a GM vehicle with twist axle rear suspension was performed and briefly discussed. Instead of using strain data from the twist axle for correlation channels, inboard channels such as shock tower vertical and trailing arm forces were used in the test development.

There is an increasing demand in automated manufacturability analysis of metal castings at the initial stages of their design. This paper presents a system developed for virtual manufacturability analysis of casting components. The system can be used by a casting designer to evaluate manufacturability of a part designed for various manufacture processes including casting, heat treatment, and machining. The system uses computational geometrics and geometric reasoning to extract manufacturing features and geometry characteristics from a part CAD model. It uses an expert system and a design database consisting of metal casting, heat treatment and machining process knowledge and rules to present manufacturability analysis results and advice to the designer. Application of the system is demonstrated for the manufacturability assessment of automotive cast aluminum components.

The USDOT and the Crash Avoidance Metrics Partnership-Vehicle Safety Communications 2 (CAMP-VSC2) Consortium (Ford, GM, Honda, Mercedes, and Toyota) initiated, in December 2006, a three-year collaborative effort in the area of wireless-based safety applications under the Vehicle Safety Communications-Applications (VSC-A) Project. The VSC-A Project developed and tested communications-based vehicle safety systems to determine if Dedicated Short Range Communications (DSRC) at 5.9 GHz, in combination with vehicle positioning, would improve upon autonomous vehicle-based safety systems and/or enable new communications-based safety applications.

The United States Department of Transportation (USDOT) and the Crash Avoidance Metrics Partnership-Vehicle Safety Communications 2 (CAMP-VSC2) Consortium (Ford, General Motors, Honda, Mercedes-Benz, and Toyota) initiated, in December 2006, a three-year collaborative effort in the area of wireless-based safety applications under the Vehicle Safety Communications-Applications (VSC-A) Project. The VSC-A Project developed and tested Vehicle-to-Vehicle (V2V) communications-based safety systems to determine if Dedicated Short Range Communications (DSRC) at 5.9 GHz, in combination with vehicle positioning, would improve upon autonomous vehicle-based safety systems and/or enable new communications-based safety applications.

A survey of vehicle refueling practices in California during the gasoline shortage of 1979 indicates that the use of leaded gasoline in catalyst equipped vehicles was occurring at a rate of about 1.6%. This 1.6% “misfueling” rate is lower than has been predicted by the U.S. Environmental Protection Agency and is almost exclusively the result of the refueling that occurs at self-service gasoline pumps. About three-quarters of the misfueled vehicles were apparently operated on leaded gasoline routinely. Based on the effect that leaded fuel has on the exhaust emission characteristics of catalyst equipped vehicles it is estimated that misfueling in California is increasing hydrocarbon and carbon monoxide emissions by about 4% and 1.6%, respectively from late model passenger cars.

There have been a half dozen surveys performed by the California Air Resources Board in California from December, 1977 to July, 1982 to determine the rate of vehicle misfueling in California. There has been great concern raised over misfueling which leads to the poisoning of catalysts and the subsequent increases in emissions of hydrocarbons, carbon monoxide and oxides of nitrogen. The results of observing refueling at service stations indicate a misfueling rate of about 2% which is much lower than what the U. S. Environmental Protection Agency figures indicate. Misfueling at self-serve stations is more than twice that noted at full-serve stations. The primary reasons given by motorists for misfueling are cheaper price of unleaded gasoline, performance (including pinging) and unavailability of unleaded fuel. Misfueling was accomplished primarily as a result of a modified restrictor or filler neck.

Current California law requires the implementation of a mandatory annual vehicle emissions inspection and maintenance program in the South Coast Air Basin by 1978. The pilot phase of this inspection program is now in operation in the City of Riverside. This paper evaluates the Riverside program and an alternate program for their abilities to detect gross emitters and provide cost/effective emissions reductions. A surveillance program was conducted to evaluate the Riverside loaded-mode inspection regime and an alternate idle inspection regime. Emissions and fuel economy tests indicated that there was no significant difference between the two regimes. Each regime resulted in immediate reductions on repaired vehicles of 35-40% in hydrocarbon emissions and 30-35% in carbon monoxide emissions, with no significant change in oxides of nitrogen emissions. There was a small (1-4%) improvement in fuel economy, and the average repair cost was $20-25.

Handling and tire performance continue to evolve due to significant improvements in vehicle, electronics, and tire technology over the years. This paper examines the trends in handling and tire performance metrics for production cars and trucks since the 1980's. This paper is based on a significant number of directional response and tire tests conducted during that period. It describes ranges of these parameters and shows how they have changed over the past thirty years.

Vehicle exhaust emissions measurements are reported for full-size panel vans operating on four alternative motor fuels and control gasoline. The emissions tests produced data on in-use vans. The vans were taken directly from commercial delivery service for testing as they accumulated mileage over a 24-month period. The alternative fuels tested were compressed natural gas, propane gas, California Phase 2 reformulated gasoline (RFG), and methanol (M-85 with 15 percent RFG). The control gasoline for the emissions tests was an industry average unleaded blend (RF-A). The vehicle technologies tested represent those options available in 1992 that were commercially available from Ford, Chrysler, and Chevrolet or which these manufacturers agreed to provide as test vans for daily use in commercial service by FedEx.

Recent changes to the U.S. CAFÉ (Corporate Average Fuel Economy) requirements have caused increased focus on alternative vehicle component designs that offer mass savings while maintaining overall vehicle design and performance targets. The instrument panel components comprise approximately 6% of the total vehicle interior mass and are thus a key component of interest in mass optimization efforts. Typically, instrument panel structures are constructed of low carbon tubular steel cross car members with welded stamped steel component brackets. In some cases, instrument panel structures have incorporated high strength low alloy (HSLA) steels to reduce mass by reducing gage. In this study, aluminum low mass instrument panel structure concept designs are developed. This paper illustrates the differences between a HSLA steel solution and four different aluminum instrument panel structure designs.

In order to assess the possible ways of energy transfer from the various sources of excitation in a vehicle assembly to a given target location, frequency based substructuring technique and transfer path analysis are used. These methods help to locate the most important energy transfer paths for a specific problem, and to evaluate their individual effects on the target, thus providing valuable insight into the mechanisms responsible for the problem. The Source-Path-Receiver concept is used. The sources can be from the road surface, engine, transmission, transfer case, prop-shaft, differential, rotating components, chain drives, pumps, etc., and the receiver can be driver/passenger ears, steering column, seats, etc. This paper is devoted to identify the noise transfer paths and the force transmissibility among the interfaces of different components in the vehicle for the low to mid frequency range.