Search Results

COMPARISON of work capacity per unit mass and volume of different energy carriers shows that liquid hydrocarbons are superior to other energy sources. Solar and nuclear powerplants as well as their use in conjunction with a steam engine are examined in this paper. Suitability of an electric drive is discussed. Using a production 2-stroke diesel engine and its development forecast, a comparison is made of spark ignition, diesel, and gas turbine engines. The status of the free-piston engine turbine combination is reviewed.

The strain-life approach is now commonly used for fatigue life analysis and predictions in the ground vehicle industry. This approach requires the use of material properties obtained from strain-controlled uniaxial fatigue tests. These properties include fatigue strength coefficient (σf′), fatigue strength exponent (b), fatigue ductility coefficient (εf′), fatigue ductility exponent (c), cyclic strength coefficient (K′), and cyclic strain hardening exponent (n′). To obtain the aforementioned properties for the material, raw data from stable cyclic stress-strain loops are fitted in log-log scale. These data include total, elastic and plastic strain amplitudes, stress amplitude, and fatigue life. Values of the low cycle fatigue properties (σf′, b, εf′, c) determined from the raw data depend on the method of measurement and fitting. This paper examines the merits and influence of using different measurement and fitting methods on the obtained properties.

Since 1985, the Body Division of the Automotive Corrosion and Prevention Committee of SAE (ACAP) has conducted biannual surveys of automotive body corrosion in the Detroit area. The purpose of these surveys is to track industry wide corrosion protection improvements and to make this information available for public consumption. The survey consists of a closed car parking lot survey checking for perforations, blisters, and surface rust. This paper reports the results of the five surveys conducted to date.

This study evaluated multi-layer steel and composite head gaskets of various thicknesses (0.43 to 1.5 mm) and fire-ring diameters to determine the influence of head gasket crevices on engine-out hydrocarbon (HC) emissions. The upper limit in the percent reduction in HC emissions from gasket-design modifications is estimated to be about 15%. At part-load conditions, the lowest HC emissions were measured for head-gasket thickness of about 1 mm. Significantly smaller thicknesses of the order of 0.4 mm result in an increase in HC emissions. Substantial hydrocarbon-emissions advantage may be realized by minimizing the gasket-to-cylinder bore offset.

Diesel exhaust gas dilution and odor intensity were measured in the immediate vicinity of a transit bus equipped with a rear-mounted horizontal exhaust pipe, a rear-mounted vertical exhaust pipe, and a roof-top diffusion system. Exhaust dilution ratios were measured indoors during vehicle idle operation, using propane added to the exhaust gas as a tracer. Exhaust odor intensities were measured also indoors during vehicle idle operation by a human panel, using a threshold odor measurement technique. On the average, the dilution of the exhaust gas around the bus with the vertical exhaust pipe was about eight times greater than it was with the horizontal pipe. Odor intensity, as measured by the threshold response distance, was about 35% less with the vertical pipe than with the horizontal pipe. The roof-top diffuser was not as effective as the vertical exhaust pipe in increasing exhaust gas dilution or in reducing exhaust odor intensity.

Several factors have influenced the size and design of domestic passenger cars over the past 30 years. Of most significance has been the influx of imported cars, initially from Europe, later from Japan. Interspersed within the fabric of this influx have been two energy crises and several recessions, and the onset of safety, emission, and energy regulations. These factors have led to various responses by domestic manufacturers as indicated by the types of products and vehicle systems that they have introduced during this period. This paper chronicles both the events as well as the responses.

This paper describes the performance attributes of the all-new front and rear SLA (short-long arm) suspensions, steering system, and tires of the 1997 Corvette. The process by which these subsystem attributes flowed down from vehicle-level requirements for ride and handling performance is briefly described. Additionally, where applicable, specific subsystem attributes are rationalized back to a corresponding vehicle-level performance requirement. Suspension kinematic and compliance characteristics are described and contrasted to those of the previous generation (1984 to 1996 Model Year) Corvette. Both synthesis/analysis activities as well as mule-level vehicle development work are cited for their roles in mapping out specific subsystem attributes and related vehicle performance.

In order to meet progressively stringent regulations on particulate emission from diesel engines, GM has developed and tested a variety of trap oxidizer systems over the years. A particulate trap system for a light duty diesel engine has been selected and developed based on this experience, with particular emphasis on production feasibility. The system components have been designed and developed in collaboration with potential suppliers, to the extent possible. The technical performance of this system has been demonstrated by successful system durability testing in the test cell and vehicle experience in computer controlled automatic operation mode. Although the system shows promise, its production readiness will require more development and extensive vehicle validation under all operating conditions.

A running loss test procedure has been developed which integrates a point-source collection method to measure fuel evaporative running loss from vehicles during their operation on the chassis dynamometer. The point-source method is part of a complete running loss test procedure which employs the combination of site-specific collection devices on the vehicle, and a sampling pump with sampling lines. Fugitive fuel vapor is drawn into these collectors which have been matched to characteristics of the vehicle and the test cell. The composite vapor sample is routed to a collection bag through an adaptation of the ordinary constant volume dilution system typically used for vehicle exhaust gas sampling. Analysis of the contents of such bags provides an accurate measure of the mass and species of running loss collected during each of three LA-4* driving cycles. Other running loss sampling methods were considered by the Auto-Oil Air Quality Improvement Research Program (AQIRP or Program).

During braking, the ability to utilize available tire-road friction is determined by brake balance. Previous methods for objectively measuring balance require various degrees of vehicle instrumentation and modification. The Road Transducer is a new measurement technique based on instrumented sections of roadway. Individual braking forces developed by each wheel are measured without vehicle instrumentation, modification, or special set up. This facilitates assessment of many vehicles required for statistical analyses. Brake balance data for several hundred vehicles are presented and provide insight to the nominal levels and variability of braking efficiencies found in the field.

Typically, “Reliability and Maintainability (R&M)” is perceived as a tool for products alone. Putting emphasis on reliability only at the cost of maintainability is another archetype. Inclusion of both reliability and maintainability (R&M) in all the phases of the machinery and equipment (M&E) life cycle is required in order to be world competitive in manufacturing. R&M is mainly a design function and it should be a part of any design review. Inclusion of the R&M concept early in the life cycle of M&E is key to cost effective and competitive manufacturing. Neither responsive manufacturing nor preventive maintenance can raise it above the level of inherent R&M.

The ozone forming potential (OFP) and specific reactivity (SR) of tailpipe exhaust are among the regulated factors that determine the environmental impact of a motor vehicle. OFP and SR measurements require a lengthy determination of about 160 non-methane hydrocarbon species. A rapid gas chromatography (GC) instrument has been constructed to separate both the light (C2 - C4) and the midrange (C5 - C12) hydrocarbons in less than 10 minutes. The limit of detection was about 0.002 parts per million carbon (ppmC). Twelve exhaust samples from two vehicles were analyzed to compare the rapid GC method with the standard GC method, which required 40-minute analyses on two different instruments. Speciation and reactivity data from the two methods were comparable. The increased sample throughput of rapid GC promises to improve OFP and SR measurements, particularly when good statistical data are necessary to insure accurate, precise results for low emission vehicles

General Motors has developed a portfolio of advanced propulsion vehicles that has set the standard for optimal fuel economy in full-size utility vehicles. An overview of power electronics used in this portfolio, already available in the market, is presented. These components are key enablers for the strategic products in portfolio. Block diagrams for various configurations are also described to show common power electronics components used in traction and auxiliary systems. Briefly real wheel drive (RWD) and front wheel drive (FWD) vehicle applications are described. Specific analysis and test results are presented from development of Traction Power Inverter used in RWD vehicles. Vehicle-based durability profiles are used in analysis to predict IGBT power modules thermal performance. Using key metrics for volume and mass, benchmarking data is also presented.

The development of a plasma jet ignition system is described on a 4-cyl, 140 in3 engine. Performance was evaluated on the basis of combustion flame photographs in a single-cylinder engine at 20/1 A/F dynamometer tests on a modified 4-cyl engine, and cold start emissions, fuel economy, and drivability in a vehicle at 19/1 air fuel ratio. In addition to adjustable engine variables such as air-fuel ratio and spark advance, system electrical and mechanical parameters were varied to improve combustion of lean mixtures. As examples, the air-fuel ratio range was 16-22/1, secondary ignition current was varied from 40 to 6000 mA, and plasma jet cavity and electrode geometry were optimized. It is shown that the plasma jet produces on ignition source which penetrates the mixture ahead of the initial flame front and reduces oxides of nitrogen emission, in comparison to a conventional production combustion chamber.

This report summarizes the methodology used in automotive industry for virtual evaluation of vehicle structural integrity under abusive load cases. In particular, the development of a nonlinear finite element (FE) centric approach is covered that is based on the functions implemented in ABAQUS (by ABAQUS Inc.). An overview is also given for comparative study of the ABAQUS capability with the existing ADAMS (MSC Software) based methods.

The goal of this study is to assess the total Life Cycle Global Warming Impact of the current HFC-134a (R134a) refrigeration system and compare it with the effect of proposed alternatives, HFC-134a Enhanced, HFC-152 (R152a), R744, R744 Enhanced and R290, based on life cycle analysis (LCA). The enhanced systems include control strategies to elevate the compressor suction pressure as the evaporator load is reduced. The hydrofluorocarbons HFC-134a and HFC-152a are greenhouse gases (GHGs) and are subject to the Kyoto Protocol timetables, which when the treaty takes effect will require participating developed countries to reduce their overall CO2 equivalent emissions of six GHGs by at least 5% by 2012 from 1990 levels.

Since 1997, General Motors Body Manufacturing Engineering - Die Engineering Services (BME-DES) has been working jointly with our software vendor to develop and implement a parallel version of stamping simulation software for mass production analysis applications. The evolution of this technology and the insight gained through the implementation of DMP/MPP technology as well as performance benchmarks are discussed in this publication.

Analytical procedures for the speciation of hydrocarbons and oxygenates (ethers, aldehydes, ketones and alcohols) in vehicle evaporative and tailpipe exhaust emissions have been improved for Phase II studies of the Auto/Oil Air Quality Improvement Research Program (AQIRP). One gas chromatograph (GC) was used for measurement of C1-C4 species and a second GC for C4-C12 species. Detection limits for this technique are 0.005 ppm C or 0.1 mg/mile exhaust emission level at a chromatographic signal-to-noise ratio of 3/1, a ten-fold improvement over the Phase I technique. The Phase I library was modified to include additional species for a total of 154 species. A 23-component gas standard was used to establish a calibration scale for automated computer identification of species. This method identifies 95±3% of the total hydrocarbon mass measured by GC for a typical exhaust sample. Solid adsorbent cartridges or impingers were used to collect aldehydes and ketones.

By using descriptive charts and graphs, this report provides an analysis of the IDB-C network at the Subsystem level and at the vehicle level, using data comparison between modeling and simulation of the network and measurement and analysis on physical systems.

The purpose of this paper is to provide an overview of the process of selection, development and approval of General Motors original equipment TPC passenger car tires. We have attempted to minimize detail in each specific area, but intend to provide a general comprehension of the thought processes involved and the procedures used to select the proper tire size and type for a vehicle. We will then describe the tire performance criteria involved in the overall development and approval process and will subsequently consider tire noise requirements in somewhat greater detail. The paper will conclude by describing the General Motors Tire Performance Criteria (TPC) System, which is a documentation of the General Motors Tire Performance requirements and test procedures.