Search Results

Past studies have shown the applicability of advanced numerical methods for crashworthiness simulation. Lumped parameter (LP) modeling and finite element (FE) modeling have been demonstrated as two useful methodologies for achieving this endeavor. Experimental tests and analytical modeling using LP and FE techniques were performed on an experimental vehicle in order to evaluate the compatibility and interrelationship of the two numerical methods for crashworthiness simulation. The objective of the numerical analysis was to simulate the vehicle crashworthiness in a 0 degree, 48.6 KPH frontal impact. Additionally, a single commercial software, LS-DYNA3D, was used for both the LP and FE analysis.

The strain-life approach is now commonly used for fatigue life analysis and predictions in the ground vehicle industry. This approach requires the use of material properties obtained from strain-controlled uniaxial fatigue tests. These properties include fatigue strength coefficient (σf′), fatigue strength exponent (b), fatigue ductility coefficient (εf′), fatigue ductility exponent (c), cyclic strength coefficient (K′), and cyclic strain hardening exponent (n′). To obtain the aforementioned properties for the material, raw data from stable cyclic stress-strain loops are fitted in log-log scale. These data include total, elastic and plastic strain amplitudes, stress amplitude, and fatigue life. Values of the low cycle fatigue properties (σf′, b, εf′, c) determined from the raw data depend on the method of measurement and fitting. This paper examines the merits and influence of using different measurement and fitting methods on the obtained properties.

Since 1985, the Body Division of the Automotive Corrosion and Prevention Committee of SAE (ACAP) has conducted biannual surveys of automotive body corrosion in the Detroit area. The purpose of these surveys is to track industry wide corrosion protection improvements and to make this information available for public consumption. The survey consists of a closed car parking lot survey checking for perforations, blisters, and surface rust. This paper reports the results of the five surveys conducted to date.

Several factors have influenced the size and design of domestic passenger cars over the past 30 years. Of most significance has been the influx of imported cars, initially from Europe, later from Japan. Interspersed within the fabric of this influx have been two energy crises and several recessions, and the onset of safety, emission, and energy regulations. These factors have led to various responses by domestic manufacturers as indicated by the types of products and vehicle systems that they have introduced during this period. This paper chronicles both the events as well as the responses.

This paper describes some methods for greatly reducing or possibly eliminating subjective tuning of suspension parts for ride and handling. Laptop computers can now be used in the vehicle to guide the tuning process. The same tools can be used to select solutions that reduce sensitivity to production and environmental variations. OBJECTIVE Reduce or eliminate time required for tuning of suspension parts for ride characteristics. Improve the robustness of ride performance relative to variations in ambient temperature and production tolerances. PROBLEM REQUIRING SOLUTION AND METHOD OF APPROACH Traditional development programs for new vehicles include time-consuming subjective ride evaluations. One example is shock absorber tuning. Even if sophisticated models define force-velocity curves, numerous hardware iterations are needed to find valvings that will reproduce the curves. Many evaluation rides are needed to modify the valvings to meet performance targets.

Typically, “Reliability and Maintainability (R&M)” is perceived as a tool for products alone. Putting emphasis on reliability only at the cost of maintainability is another archetype. Inclusion of both reliability and maintainability (R&M) in all the phases of the machinery and equipment (M&E) life cycle is required in order to be world competitive in manufacturing. R&M is mainly a design function and it should be a part of any design review. Inclusion of the R&M concept early in the life cycle of M&E is key to cost effective and competitive manufacturing. Neither responsive manufacturing nor preventive maintenance can raise it above the level of inherent R&M.

This report summarizes the methodology used in automotive industry for virtual evaluation of vehicle structural integrity under abusive load cases. In particular, the development of a nonlinear finite element (FE) centric approach is covered that is based on the functions implemented in ABAQUS (by ABAQUS Inc.). An overview is also given for comparative study of the ABAQUS capability with the existing ADAMS (MSC Software) based methods.

The complexity of designing and implementing a vehicle electrical control system for ultra fuel-efficient hybrid vehicles is significantly greater than that of a conventional vehicle. To quickly demonstrate and iterate capabilities of these vehicles, an efficient and rapid means for developing requirements, mapping these into an electrical control and communications architecture, and developing prototype systems is needed. The General Motors Precept concept vehicle is an example of an energy- efficient vehicular control system developed using a "requirements to software'' development process and electronic controller infrastructure that demonstrates these attributes. The Precept is General Motors Corporation's technology demonstration concept vehicle developed to address General Motors Corporation's commitment to the Partnership for a New Generation (PNGV) program.

Since 1997, General Motors Body Manufacturing Engineering - Die Engineering Services (BME-DES) has been working jointly with our software vendor to develop and implement a parallel version of stamping simulation software for mass production analysis applications. The evolution of this technology and the insight gained through the implementation of DMP/MPP technology as well as performance benchmarks are discussed in this publication.

By using descriptive charts and graphs, this report provides an analysis of the IDB-C network at the Subsystem level and at the vehicle level, using data comparison between modeling and simulation of the network and measurement and analysis on physical systems.

The purpose of this paper is to provide an overview of the process of selection, development and approval of General Motors original equipment TPC passenger car tires. We have attempted to minimize detail in each specific area, but intend to provide a general comprehension of the thought processes involved and the procedures used to select the proper tire size and type for a vehicle. We will then describe the tire performance criteria involved in the overall development and approval process and will subsequently consider tire noise requirements in somewhat greater detail. The paper will conclude by describing the General Motors Tire Performance Criteria (TPC) System, which is a documentation of the General Motors Tire Performance requirements and test procedures.

Free form fabrication, or rapid prototyping as it is commonly known, is the creation of a physical entity, directly from numerical description, using an additive process. The mathematical data used is typically in the form of a 3D CAD file, but it may also be obtained from a reverse engineering process. This paper presents a review of three of the leading FFF (free form fabrication) systems which are commercially available. Time constraints will allow us to describe only three of these products. Although this does not do justice to a technology where there are more than 30 different systems in various stages of development, these examples represent the vast majority of machines which are in the marketplace today.

The free-rolling cornering, straight-line braking, and pull force properties of a small sample of tire specifications is examined. This is done to examine potential differences between the specifications and the statistics of force and moment measurements. Two steer axle specifications, two drive axle specifications, and a trailer specification are considered, In addition, the evolution of properties for one drive axle specification is followed from new to naturally worn-out to retreaded. The summarized data is available from SAE Cooperative Research on electronic media.

Commercially available software tools are widely used to assist in conducting life cycle inventory, life cycle assessment (LCA), life cycle impact analysis (LCIA), and design for the environment (DfE) studies. Five leading software tools, Boustead 4.2, GaBi 3.2, SimaPro 4.0, TEAM 3.0, and Toolkit, currently in use or under consideration by life cycle practitioners, were selected for testing, and a detailed evaluation scheme was used to evaluate the effectiveness of these tools for practical application in automotive life cycle studies. A consensus numerical score for each of 20 separate test criteria was assigned to each of the software packages under evaluation, and the total scores compared. On the basis of these scores, the authors chose GaBi version 3.2 as the LCA software package currently best suited for use by experienced life cycle practitioners in conducting environmental life cycle assessments in the automotive industry.

Electro-Motive Division of GM jointly with HRL Laboratories have developed a software tool, called TechPro, which assists in troubleshooting of diesel locomotives. The tool has been tested extensively in the field for the last two years. It has improved significantly the quality of diagnosis of locomotives. The tool is based on Graphical Probabilistic Models and Case Data Bases. We will discuss the design of the tool, its performance and will show its relevance to diagnosis of automobiles.

By-wire systems have the potential of augmenting the normal capabilities of human drivers as well as serving as enablers for emerging safety technologies. To achieve these features, these systems must be carefully designed, analyzed, and verified for safety because they are new, complex, and potentially exhibit new and different failure modes and effects. Duplication may be required to ensure that safety margins are met in the presence of faults. Full duplication of every system may not lead to a cost effective implementation, especially if multiple independent by-wire systems are placed on a single vehicle. Other architectural approaches for the integration of by-wire systems need to be considered and analyzed. These architectures should meet if not exceed the safety requirements while providing a more cost effective implementation than a fully duplicated architecture.

The Cadillac Electronic Climate Control heating and air conditioning system provides automatic control of the passenger compartment temperature. It utilizes a microcomputer to control the operation of electrical, mechanical and vacuum components that regulate the amount and temperature of air delivered into the car to maintain the “customer set” comfort level. The first step in the evolution of this new system was to define the performance requirements. With this established, the system was then designed, tested and developed in the laboratory and on the road until this desired performance was achieved.