Search Results

In recent years, the automotive industry has seen a rapid decrease in product development cycle time and a simultaneous increase in the variety of vehicles offered in the marketplace. These trends require a rigorous yet efficient systems engineering approach to the development of automotive braking systems. This paper provides an overview of an objective process for developing and predicting vehicle-level brake performance through an approach using both laboratory subsystem testing and math modeling.

The US Environmental Protection Agency (EPA)’s heavy duty diesel emission standard was tightened beginning from 2007 with the introduction of ultra-low-sulfur diesel fuel. Most heavy duty diesel applications were required to equip Particulate Matter (PM) after-treatment systems to meet the new tighter, emission standard. Systems utilizing Diesel Oxidation Catalyst (DOC) and Catalyzed-Diesel Particulate Filter (DPF) are a mainstream of modern diesel PM after-treatment systems. To ensure appropriate performance of the system, periodic cleaning of the PM trapped in DPF by its oxidation (a process called “regeneration”) is necessary. As a result, of this regeneration, DOC’s and DPF’s can be exposed to hundreds of thermal cycles during their lifetime. Therefore, to understand the thermo-mechanical performance of the DOC and DPF is an essential issue to evaluate the durability of the system.

Over the past five years, the US Automotive Materials Partnership (USAMP) has brought together representatives from DaimlerChrysler, General Motors, Ford Motor Company and over 40 other participant companies from the Mg casting industry to create and test a low-cost, Mg-alloy engine that would achieve a 15 - 20 % Mg component weight savings with no compromise in performance or durability. The block, oil pan, and front cover were redesigned to take advantage of the properties of both high-pressure die cast (HPDC) and sand cast Mg creep- resistant alloys. This paper describes the alloy selection process and the casting and testing of these new Mg-variant components. This paper will also examine the lessons learned and implications of this pre-competitive technology for future applications.

A review of available information on the effect that brake rotor crossdrilling has on brake performance reveals a wide range of claims on the subject, ranging from ‘minimal effect, cosmetic only’ to substantially improving brake cooling and fade resistance. There are also several theories on why brake rotor crossdrilling could improve fade performance, including crossdrill holes providing a path for ‘de-gassing’ of the brake lining material and increasing the mechanical interaction, or ‘grip’ of the lining material on the rotor. This paper reviews three case studies in which the opportunity arose to compare the performance of brake systems with crossdrilled versus non crossdrilled brake rotors in otherwise identical brake corner designs. The effect of brake rotor crossdrilling on brake cooling, brake output, brake fade, wet brake output, and brake wear rates were studied using both on-vehicle and dynamometer data.

Tensile measurements and fracture surface analysis of low carbon heat-treated boron steel are reported. Tensile coupons were quasi-statically deformed to fracture in a miniature tensile testing stage with custom data acquisition software. Strain contours were computed via a digital image correlation method that allowed placement of a digital strain gage in the necking region. True stress-true strain data corresponding to the standard tensile testing method are presented for comparison with previous measurements. Fracture surfaces were examined using scanning electron microscopy and the deformation mechanisms were identified.

Managing (minimizing and optimizing) the total mass of a vehicle is recognized as a critical task during the development of a new vehicle, as well as throughout its production lifecycle. This paper summarizes a literature review of, and investigation into, the strategies, methods and best practices for achieving low total mass in new vehicle programs, and/or mass reductions in existing production vehicle programs. Empirical and quantitative data and examples from the automotive manufacturers and suppliers are also provided in support of the material presented.

Over the past decade, the automotive industry has seen a rapid decrease in product development cycle time and an ever increasing need by original equipment manufacturers and their suppliers to differentiate themselves in the marketplace. This differentiation is increasingly accomplished by introducing new technology while continually improving the performance of existing automotive systems. In the area of automotive brake system design, and, in particular, the brake apply subsystem, an increased focus has been placed on the development of electrohydraulic apply systems and brake-by-wire systems to replace traditional pneumatic and hydraulic systems. Nevertheless, the traditional brake apply systems, especially vacuum-based or pneumatic systems, will continue to represent the majority of brake apply system production volume into the foreseeable future, which underscores the need to improve the performance and application of these traditional systems in passenger cars and light-trucks.

Diesel engines offer better fuel economy compared to their gasoline counterpart, but simultaneous control of NOx and particulates is very challenging. The blended 2-way SCR/DPF is recently emerging as a compact and cost-effective technology to reduce NOx and particulates from diesel exhaust using a single aftertreatment device. By coating SCR catalysts on and inside the walls of the conventional wall-flow filter, the 2-way SCR/DPF eliminates the volume and mass of the conventional SCR device. Compared with the conventional diesel aftertreatment system with a SCR and a DPF, the 2-way SCR/DPF technology offers the potential of significant cost saving and packaging flexibility. In this study, an engine dynamometer test cell was set up to repeatedly load and regenerate the SCR/DPF devices to mimic catalyst aging experienced during periodic high-temperature soot regenerations in the real world.

Heat transfer to the combustion chamber walls constitutes a significant portion of the overall energy losses over the working cycle of a direct injection (DI) diesel engine. In the last few decades, numerous research efforts have been devoted to investigating the prospects of boosting efficiency by insulating the combustion chamber. Relatively few studies have focused on the prospects of reducing emissions by applying combustion chamber insulation. A main purpose of this study is to assess the potential of reducing in-cylinder soot as well as boosting aftertreatment performance by means of partially insulating the combustion chamber. Based on the findings from a conceptual study, a Low Heat Rejection (LHR) design, featuring a Nimonic 80A insert into an Aluminum piston, was developed and tested experimentally at various loads in a single-cylinder Hatz-engine.

Homogeneous Charge Compression Ignition (HCCI) is a combustion concept which has the potential for efficiency comparable to a DI Diesel engine with low NOx and soot emissions. However, HCCI is difficult to control, especially at low speeds and loads. One way to assist with combustion control and to extend operation to low speed and loads is to close the exhaust valve before TDC of the exhaust stroke, trapping and recompressing some of the hot residual. Further advantages can be attained by injecting the fuel into this trapped, recompressed mixture, where chemical reactions occur that improve ignitability of the subsequent combustion cycle. Even further improvement in the subsequent combustion cycle can be achieved by applying a spark, leading to a spark-assisted HCCI combustion concept.

The Representative Interactive Flamelet (RIF) - model has established itself as a model well suited for capturing conventional non-premixed combustion in diesel engines. There are concerns about applying the concept to model combustion modes characterized by high degrees of premixing, since it is argued that the fast-chemistry assumption, on which the model is based, breaks down. However, the level of premixing at which this occurs is still not well established. In this paper the model is successfully applied to the so-called Premixed Charge Compression Ignition (PCCI) mode of combustion, characterized by relatively early injection timings, high EGR, and cooled intake air. For very advanced injection timings, an alternative modeling approach is developed.

Several methods are currently used to enforce motion in different types of noise and vibration models. Experimentally based FRF models often use a matrix inversion technique to enforce motion. In finite element models, the large mass method is one that is very commonly used. A literature review has shown few guidelines for determining the size of these large masses. In this paper, the relationship between the matrix inversion technique and the large mass method is derived. From this relationship, conditions necessary for these large mass FEM models to converge to the same answers as the matrix inversion technique are derived. These conditions are then used to develop a criterion for determining a smallest possible large mass. Results from a simple model are presented to demonstrate the criterion.

The focus of this research effort was to develop a technique to measure the cyclic variability of the mass injected by fuel injectors. Successful implementation of the measurement technique introduced in this paper can be used to evaluate injectors and improve their designs. More consistent and precise fuel injectors have the potential to improve fuel efficiency, engine performance, and reduce emissions. The experiments for this study were conducted at the Michigan State University Automotive Research Experiment Station. The setup consists of a fuel supply vessel pressurized by compressed nitrogen, a Dantec laser Doppler anemometry (LDA) system to measure the centerline velocity of fuel, a quartz tube for optical access, and a Cosworth IC 5460 to control the injector. The detector on the LDA system is capable of resolving Doppler bursts as short as 6μs, depending on the level of seeding, thus giving a detailed time/velocity profile.

A fully flexible valve actuation (FFVA) system was developed for a single cylinder research engine to investigate high efficiency clean combustion (HECC) in a diesel engine. The main objectives of the study were to examine the emissions, performance, and combustion characteristics of the engine using late intake valve closing (LIVC) to determine the benefits and limitations of this strategy to meet Tier 2 Bin 5 NOx requirements without after-treatment. The most significant benefit of LIVC is a reduction in particulates due to the longer ignition delay time and a subsequent reduction in local fuel rich combustion zones. More than a 95% reduction in particulates was observed at some operating conditions. Combustion noise was also reduced at low and medium loads due to slower heat release. Although it is difficult to assess the fuel economy benefits of LIVC using a single cylinder engine, LIVC shows the potential to improve the fuel economy through several approaches.

Sheet metal forming processes change the material properties due to work hardening (or softening) in the thickness direction as well as throughout the entire part. At the same time, uneven thickness distribution, mostly thinning, occurs as the result of forming. This is true for all commonly used sheet metal forming processes including stamping (deep drawing), tube hydroforming, sheet hydroforming and super plastic forming. The effects from forming can sometimes strongly influence the structural performance. Though the CAE analysts have been trying to consider forming effect in their models for performance simulations, there was no easy way to do it consistently and reliably. Some analysts have been trying to modify the initial gage or yield strength to compensate for the property change due to forming. Replace the model with the formed panel is not feasible due to the mesh density difference.

Over the last decade significant efforts have been made in the automotive industry to move into a math-based control development approach where much of the development could be done off-line using computer simulations. High-fidelity simulation of an engine and control system helps to shorten controller development time with reduced risk. This requires the integration of a detailed engine model with a representative controller model. This paper describes the development and validation of an integrated engine and controller model of a turbocharged diesel engine. The integrated model incorporates a detailed engine model in GT-Power and a comprehensive controller model in Simulink with functionalities like the production ECM. The focus of this study is a non-real time simulation and analysis of the control of EGR, turbocharger, and fueling with engine performance.

The following document is a set of guidelines intended to be used as a reference for the practicing automotive sound quality (SQ) engineer with the potential for application to the field of general consumer product sound quality. Practicing automotive sound quality engineers are those individuals responsible for understanding and/or conducting the physical and perceptual measurement of automotive sound. This document draws upon the experience of the four authors and thus contains many “rules-of-thumb” which the authors have found to work well in their many automotive related sound quality projects over the past years. When necessary, more detailed publications are referenced. The intent of publication of this document is to provide a reference to assist in automotive sound quality work efforts and to solicit feedback from the general sound quality community as to the completeness of the material presented.

This paper will describe an investigation of the formability of high strength steel (HSS) laser welded blanks (LWBs). Anticipated combinations of thickness and steel grades, including high strength low alloy (HSLA) and dual phase (DP) steels were selected. The blanks were characterized through chemical analysis and mechanical testing, as well as microstructural analysis of the weld. Samples were strained in a limiting dome height tester. Weld line movement, dome height and strain at failure were then measured. Data from these tests resulted in development of forming limit diagrams, and allowed correlation of weld line movement to forming conditions. In part, the results showed that the presence of the weld has a negative influence on formability, and that balancing the load carrying capacity of each side of the blank results in minimum weld line movement in the blanks.

Exhaust gas recirculation (EGR) is one of the key approaches applied to reduce emissions for an internal combustion engine. Recirculating a desired amount of EGR requires accurately estimating EGR mass flow. This can be calculated either from the gas flow equation of an orifice, or from the difference between charge air mass flow and fresh air mass flow. Both calculations need engine exhaust pressure as an input variable. This paper presents a method to estimate exhaust pressure for a variable geometry turbo charged diesel engine. The method is accurate and simple to fit production ECU application, therefore, saves cost of using a physical sensor.

Recently, a new technology, termed 2-way SCR/DPF by the authors, has been developed by several catalyst suppliers for diesel exhaust emission control. Unlike a conventional emission control system consisting of an SCR catalyst followed by a catalyzed DPF, a wall-flow filter is coated with SCR catalysts for controlling both NOx and PM emissions in a single catalytic converter, thus reducing the overall system volume and cost. In this work, the potential and limitations of the Cu/Zeolite-based SCR/DPF technology for meeting future emission standards were evaluated on a pick-up truck equipped with a prototype light-duty diesel engine.