Search Results

Disc brakes operate with very close proximity of the brake pads and the brake rotor, with as little as a tenth of a millimeter of movement of the pads required to bring them into full contact with the rotor to generate braking torque. It is usual for a disc brake to operate with some amount of residual drag in the fully released state, signifying constant contact between the pads and the rotor. With this contact, every miniscule movement of the rotor pushes against the brake pads and changes the forces between them. Sustained loads on the brake corner, and maneuvers such as cornering, can both produce rotor movement relative to the caliper, which can push it steadily against one or both of the brake pads. This can greatly increase the residual force in the caliper, and increase drag. This dependence of drag behavior on the movement of the brake rotor creates some vehicle-dependent behavior.

In the context of vehicle electrification, improving vehicle aerodynamics is not only critical for efficiency and range, but also for driving experience. In order to balance the necessary trade-offs between drag and downforce without significant impact on the vehicle styling, we see an increasing amount of active aerodynamic solutions on high-end passenger vehicles. Active rear spoilers are one of the most common active aerodynamic features. They deploy at high vehicle speed when additional downforce is required [1, 2]. For a vehicle with an active rear spoiler, the aerodynamic performance is typically predicted through simulations or physical testing at different static spoiler positions. These positions range from fully stowed to fully deployed. However, this approach does not provide any information regarding the transient effects during the deployment of the rear spoiler, which can be critical to understanding key performance aspects of the system.

Currently, Model Based Development (MBD) is the de-facto methodology in automotive industry. This has led to conversions of legacy code to Simulink models. Our previous work was related to implementing the C2M tool to automatically convert legacy code to Simulink models. While the tool has been implemented and deployed on few OEM pilot code-sets there were several improvement areas identified w.r.t. the generated models. One of the improvement areas identified was that the generated model used atomic blocks instead of abstracted blocks available in Simulink. E.g. the generated model used an ADD block and feedback loop to represent an integration operation instead of using an integrator block directly. This reduced the readability of the model even though the functionality was correct. Thus, as a user of the model, an engineer would like to see abstract blocks rather than atomic blocks.

Electric motor whine is a major NVH source for electric vehicles. Traditional mitigation methods focus on e-motor hardware optimization, which requires long development cycles and may not be easily modified when the hardware is built. This paper presents a control- and software-based strategy to reduce the most dominant motor order of an IPM motor for General Motors’ Ultium electric propulsion system, using the patented active Torque Ripple Cancellation (TRC) technology with harmonic current injection. TRC improves motor NVH directly at the source level by targeting the torque ripple excitations, which are caused by the electromagnetic harmonic forces due to current ripples. Such field forces are actively compensated by superposition of a phase-shifted force of the same spatial order by using of appropriate current.

This paper describes the design of a supervisory multivariable constrained Model Predictive Control (MPC) system for driver requested axle torque tracking with real-time fuel economy optimization that is scheduled for production by General Motors starting in 2018. The control system has been conceived and co-developed by General Motors and ODYS. The control approach consists of a set of linear MPC controllers scheduled in real-time based on powertrain operating conditions. For each MPC controller, a linear model is obtained by system identification with vehicle and dynamometer data. The supervisory MPC coordinates in real time desired Continuously Variable Transmission (CVT) ratio and desired engine torque to satisfy the system requirements, based on estimates of axle torque and engine fuel rate, by solving a constrained optimization problem at each sampling step. Each linear MPC controller is equipped with a Kalman filter to reconstruct the system state from available measurements.

The REAL NOx regulation requires tracking and reporting of NOx emissions starting in 2022MY for both medium-duty and heavy-duty diesel vehicles with potential to be considered during the next light-duty rulemaking. The regulation includes minimum NOx mass measurement accuracy requirements of either +/−20 percent or +/− 0.1 g/bhp-hr. Existing NOx sensor technology may not be able to meet the regulated accuracy requirements especially when exposed to other sources of variation within the emissions control system. This paper provides an assessment of real-world NOx sensor accuracy and the impact of other sources of variation and noise factors on NOx measurement accuracy. Noise factors investigated include NOx sensor tolerance, exhaust flow rate estimation, NOx sensor ammonia (NH3) cross sensitivity, mass air flow (MAF) sensor accuracy, NOx sensor placement, and laboratory emissions measurement capability.

Vehicle electrification is driven globally due to the increased concerns on carbon emissions. But the challenges in customer acceptance remains esp. in relation to vehicle costs. Virtual simulations can help in cutting down product development cost and enable faster launch of new vehicles. An early stage system model based design iterations can help in cutting down the product development costs and building more robust products. In the current paper, we develop and analyze a battery pack system model for early phase design. We extend a previously developed system model to include critical physics like sub-component level multiphysics for electrical joint integrity. Also, we demonstrate an integration of 3D FEM & system model for improving the accuracy of joint temperature predictions during charging and/or discharging. A typical High Voltage (HV) battery system comprises of battery modules (Li-ion cells, cooling channels, structural frames, interconnect boards) and HV bus bars.

Styrene-Butadiene Rubber (SBR), a copolymer of butadiene and styrene, is widely used in the automotive industry due to its high durability and resistance to abrasion, oils and oxidation. Some of the common applications include tires, vibration isolators, and gaskets, among others. This paper characterizes the dynamic behavior of SBR and discusses the suitability of a visco-elastic model of elastomers, known as the Kelvin model, from a mathematical and physical point of view. An optimization algorithm is used to estimate the parameters of the Kelvin model. The resulting model was shown to produce reasonable approximations of measured dynamic stiffness. The model was also used to calculate the self heating of the elastomer due to energy dissipation by the viscous damping components in the model. Developing such a predictive capability is essential in understanding the dynamic behavior of elastomers considering that their dynamic stiffness can in general depend on temperature.

Model-based control system design improves quality, shortens development time, lowers engineering cost, and reduces rework. Evaluating a control system's performance, functionality, and robustness in a simulation environment avoids the time and expense of developing hardware and software for each design iteration. Simulating the performance of a design can be straightforward (though sometimes tedious, depending on the complexity of the system being developed) with mathematical models for the hardware components of the system (plant models) and control algorithms for embedded controllers. This paper describes a software tool and a methodology that not only allows a complete system simulation to be performed early in the product design cycle, but also greatly facilitates the construction of the model by automatically connecting the components and subsystems that comprise it.

This paper describes the design of a multivariable, constrained Model Predictive Control (MPC) system for torque tracking in turbocharged gasoline engines scheduled for production by General Motors starting in calendar year 2018. The control system has been conceived and co-developed by General Motors and ODYS. The control approach consists of a set of linear MPC controllers scheduled in real time based on engine operating conditions. For each MPC controller, a linear model is obtained by system identification with data collected from engines. The control system coordinates throttle, wastegate, intake and exhaust cams in real time to track a desired engine torque profile, based on measurements and estimates of engine torque and intake manifold pressure.

Gasoline Particulate Filters (GPF) are widely employed in exhaust aftertreatment systems of gasoline engines to meet the stringent particulate emissions requirements of Euro 6 and China 6 standard. Optimization of GPF performance requires a delicate trade-off between fuel economy, engine performance and drivability. This results in a complex lengthy and iterative calibration development process which uses a lot of hardware resources. To improve the calibration process and reduce hardware testing, physics-based modeling of the GPF system is used. A 1-D chemical model supplemented with 3D CFD solver is utilized to evaluate pressure drop and soot burning performance characteristics of the GPF under engine dynamometer test conditions. The chemical kinetics of soot burning for the 1D model is developed using test data obtained from well controlled laboratory environment.

In a hydraulic system, parameter variation, contamination, and/or operating conditions can lead to instabilities in the pressure response. The resultant erratic pressure profile reduces performance and can lead to hardware damage. Specifically, in a transmission control system, the inability to track pressure commands can result in clutch or variator slip which can cause driveline disturbance and/or hardware damage. A variator is highly sensitive to slip and therefore, it is advantageous to identify such pressure events quickly and take remedial actions. The challenge is to detect the condition in the least amount of time while minimizing false alarms. A Neyman-Pearson and an energy detector (based on auto-correlation) are evaluated for the detection of pressure disturbances. The performance of the detectors is measured in terms of speed of detection and robustness to measurement noise.

Designing power electronics to operate in harsh vehicle environments while meeting packaging requirements such as mass, volume, and power density, creates several challenges for their mechanical design. In this work, we concentrate on the power inverter module (PIM) which converts high voltage (HV) DC voltage power from the HV battery to AC power to drive the motor. The PIM main components are the power module, gate drive and the bulk capacitor. The sizing and selection of the bulk capacitor and power module depend on performance criteria and drive profiles in addition to operating temperatures. In this work, we share the main challenges of packaging components within the inverter. We then discuss best practices to ensure a robust mechanical design which meets inverter durability and reliability targets for an electric vehicle application. The main challenges discussed are bulk capacitor thermals, sealing, and Silicon Carbide (SiC) packaging.

The Lockheed Martin Low-Speed Wind Tunnel (LSWT) is a closed-return wind tunnel with two solid-wall test sections. This facility originally entered into service in 1967 for aerodynamic research of aircraft in low-speed and vertical/short take-off and landing (V/STOL) flight. Since this time, the client base has evolved to include a significant level of automotive aerodynamic testing, and the needs of the automotive clientele have progressed to include acoustic testing capability. The LSWT was therefore acoustically upgraded in 2016 to reduce background noise levels and to minimize acoustic reflections within the low-speed test section (LSTS). The acoustic upgrade involved detailed analysis, design, specification, and installation of acoustically treated wall surfaces and turning vanes in the circuit as well as low self-noise acoustic wall and ceiling treatment in the solid-wall LSTS.

The performance of a High Voltage (HV) battery in an advanced propulsion application is often highly dependent on the customer controlled climate settings of the vehicle system. Cooling of the battery requires an understanding of the environment in which it is expected to operate. Results from testing on various air-cooled systems will be discussed to portray the interactions of the battery system design and the climate control system design. The following topics (in relation to battery cooling) will be discussed: climate control system temperature settings; climate-control system fan settings; climate control system recirculation mode and outside air mode settings; venting of the battery thermal system exhaust air; and the battery location and mounting.

Market demands for increased fuel economy and reduced emissions are placing higher aerodynamic and thermal analysis demands on vehicle designers and engineers. These analyses are usually carried out by different engineering groups in different parts of the design cycle. Design changes required to improve vehicle aerodynamics often come at the price of part thermal performance and vice versa. These design changes are frequently a fix for performance issues at a single performance point such as peak power, peak torque, or highway cruise. In this paper, the motivation for a holistic approach in the form of multi-disciplinary optimization (MDO) early in the design process is presented. Using a Response-surface Informed Transient Thermal Model (RITThM) a vehicle's thermal performance through a drive cycle is predicted and correlated to physical testing for validation.

The Hybrid Cellular Automaton (HCA) algorithm is a generative design approach used to synthesize conceptual designs of crashworthy vehicle structures with a target mass. Given the target mass, the HCA algorithm generates a structure with a specific acceleration-displacement profile. The extended HCA (xHCA) algorithm is a generalization of the HCA algorithm that allows to tailor the crash response of the vehicle structure. Given a target mass, the xHCA algorithm has the ability to generate structures with different acceleration-displacement profiles and target a desired crash response. In order to accomplish this task, the xHCA algorithm includes two main components: a set of meta-parameters (in addition target mass) and surrogate model technique that finds the optimal meta-parameter values. This work demonstrates the capabilities of the xHCA algorithm tailoring acceleration and intrusion through the use of one meta-parameter (design time) and the use of Kriging-assisted optimization.

The human-robot interaction (HRI) is involved in a lift assistant system of manufacturing assembly line. The admittance model is applied to control the end effector motion by sensing intention from force of applied by a human operator. The variable admittance including virtual damping and virtual mass can improve the performance of the systems. But the tuning process of variable admittance is un-convenient and challenging part during the real test for designers, while the offline simulation is lack of learning process and interaction with human operator. In this paper, the Iterative learning algorithm is proposed to emulate the human learning process and facilitate the variable admittance control design. The relationship between manipulate force and object moving speed is demonstrated from simulation data. The effectiveness of the approach is verified by comparing the simulation results between two admittance control strategies.

Due to the limitations on resistance spot welding of ultra-thin steel sheet (thicknesses below 0.5 mm) in high-volume automotive manufacturing, a comparison of friction stir spot welding and self-piercing riveting was performed to determine which process may be more amenable to enabling assembly of ultra-thin steel sheet. Statistical comparisons between mechanical properties of lap-shear tensile and T-peel were made in sheet thickness below 0.5 mm and for dissimilar thickness combinations. An evaluation of energy to fracture, fracture mechanisms, and joint consistency is presented.

The amount of acidic material in used engine oil is considered an indicator of the remaining useful life of the oil. Total acid number, determined by titration, is the most widely accepted method for determining acidic content but the method is not capable of speciation of individual acids. In this work, high molecular weight residue was isolated from used engine oil by dialysis in heptane. This residue was then analyzed using pyrolysis-comprehensive two dimensional gas chromatography with time-of-flight mass spectrometry. Carboxylic acids from C2-C18 were identified in the samples with acetic acid found to be the most abundant. This identification provides new information that may be used to improve the current acid detection methodologies for used engine oils.