Search Results

Rollover is one of the significant life threatening factors in SUVs (Sports Utility Vehicles). By applying braking or steering, active roll stability controllers help prevent rollover accidents in SUVs. The performance of these controllers is very sensitive to vehicle inertial parameters such as vehicle mass and mass center height. In this paper, a unified estimation method for vehicle mass is proposed considering available driving conditions, where three estimation algorithms are developed based on longitudinal, lateral or vertical vehicle dynamics, respectively. The first algorithm is designed using the longitudinal vehicle dynamics and the recursive least square with the disturbance observer technique for longitudinal traveling case. The second algorithm is designed using the lateral vehicle dynamics where the lateral velocity is estimated with the kinematic vehicle model via the Kalman filter.

This paper presents a model based sensor fault detection and isolation algorithm for the vertical acceleration sensors of the Continuous Damping Control (CDC) system, installed on the sprung mass. Since sensor faults of CDC system have a critical influence on the ride performance as well as the vehicle stability, the sensor fault detection algorithm must be implemented into the overall CDC algorithm. In this paper, each vertical acceleration sensor installed on the sprung mass (two in the front corners and one in the rear) separately estimates the vertical acceleration of the center of gravity of the sprung mass. Then, the sensor fault is detected by cross-checking all three vertical acceleration estimates independently obtained by the each vertical acceleration sensor.

A Light Detection And Ranging (LiDAR) is now becoming an essential sensor for an autonomous vehicle. The LiDAR provides the surrounding environment information of the vehicle in the form of a point cloud. A decision-making system of the autonomous car is able to determine a safe and comfort maneuver by utilizing the detected LiDAR point cloud. The LiDAR points on the cloud are classified as dynamic or static class depending on the movement of the object being detected. If the movement class (dynamic or static) of detected points can be provided by LiDAR, the decision-making system is able to plan the appropriate motion of the autonomous vehicle according to the movement of the object. This paper proposes a real-time process to segment the motion states of LiDAR points. The basic principle of the classification algorithm is to classify the point-wise movement of a target point cloud through the other point clouds and sensor poses.

The paper presents a new offset compensation method of a yaw rate sensor and a lateral acceleration sensor. It is necessary to compensate the offsets of the analog sensors, such as the yaw rate sensor and the lateral acceleration sensor, to acquire accurate signals. This paper proposes two different offset compensation algorithms, the sequential compensation method and the model based compensation method. Both algorithms are combined with the algorithm map depending on the vehicle driving status. The proposed algorithm is verified by the computer simulations.

A controller is introduced for air-to-fuel ratio management, and the control scheme is based on the feedback error learning method. The controller consists of neural networks with linear feedback controller. The neural networks are radial basis function network (RBFN) that are trained by using the feedback error learning method, and the air-to-fuel ratio is measured from the wide-band oxygen sensor. Because the RBFNs are trained by online manner, the controller has adaptation capability, accordingly do not require the calibration effort. The performance of the controller is examined through experiments in transient operation with the engine-dynamometer.

In CRDI diesel engines, the piezo injector is gradually replacing the solenoid injector due to the quick response of the actuator. Operating performance of the injectors in the CRDI diesel engine has an influence on engine emissions. Therefore, accurate injector control is one of the most important parts of the CRDI engine control. The objective of this paper is the development of a piezo injector driver for CRDI diesel engines. Electrical characteristics of the piezo injector were analyzed. A control strategy for charging and discharging the actuator are proposed. The developed injector driver is verified by experiments under various fuel pressures, injection durations and driving circuit voltages.

Lane keeping assistant system (LKAS) is expected to reduce the driver workload with assisting the driver during driving and is regarded as a promising active safety system. For the proposed LKAS which requires cooperative driving between driver and the assistance system, a Model Based Predictive Controller (MBPC) is proposed to minimize the effect of system overshoot caused by the time delay from the vision-based lane detection system. In order to validate the proposed LKAS controller, a HIL (Hardware In the Loop) simulator is built using steering mechanism, single camera, torque motor, sensors, etc. The performance of the proposed system is demonstrated in various roadways.

The performance of an integrated Vehicle Stability Control (VSC) system depends on not only control logic itself, but also the performance of state estimator and control threshold. In conventional VSCs, a control threshold is designed by vehicle characteristics and is centered on average drivers. A VSC algorithm with variable control threshold has been investigated in this study. The control threshold can be determined by phase plane analysis of side slip angle and angular velocity. Vehicle side slip angle estimator has been evaluated using test data. Estimated side slip angle has been used in the determination of the control threshold. The performance of the proposed VSC algorithm has been investigated by human-in-the-loop simulation using a vehicle simulator. The simulation results show that the control threshold has to be determined with respect to the driver steering characteristics.

The purpose of this paper is to develop and experimentally validate a practical and effective technique for the automatic regulation of a hydraulic semiactive vibration absorber (SAVA) for automobiles. The work relies on a consistent hydraulic model of the actuator dynamics that includes the effects of fluid compressibility and a nonlinear viscous loss characteristic. A bistate control algorithm is developed using a Lyapunov approach that seeks to dissipate the energy of the system. The performance of the proposed semiactive damper design on a quarter car model of an automobile suspension is established experimentally on a vibrating test stand. The work provides evidence that the inexpensive hardware design makes it possible to improve the ride and handling performance.