Search Results

The weight-saving requirements for automobiles are important. In order to produce a lighter engine, an aluminum block with cast-iron liners and a hypereutectic aluminum-silicon alloy block have been developed. (1)*, (2), (3), (4), (5), (6) We developed a new aluminum engine block which has the cylinder bore surface structure reinforced with short ceramic fiber. We also established technology suitable for mass-production including a fiber preform process and a non-destructive inspection method. In this paper, the optimum properties and production technology of MMC engine blocks are introduced. A portion of the paper is dedicated to the results of a comparison study between a new light-weight aluminum engine block, a hypereutectic aluminum-silicon engine block and an aluminum engine block with cast-iron liners.

This paper studies various wheel stiffness configurations, with the aim of enhancing driving stability while minimizing the increase in weight associated with an increase in stiffness. Reinforcement was added to the wheel disk and the wheel rim of standard aluminum wheels for passenger vehicles in order to produce four wheels with different stiffness configurations. The effects of disk stiffness and rim stiffness on tire contact patch profiles and driving stability were quantitatively evaluated. From the results of tests with the four wheels, it was observed that disk stiffness and rim stiffness have differing effects on tire contact patch profiles, and on driving stability. Disk stiffness influences especially tire contact patch length, and tire contact patch length influences especially maneuverability in driving stability. Rim stiffness influences especially tire contact patch area, and tire contact patch area influences especially stability in driving stability.

The use of low-density materials in body panels is increasing as a measure to reduce the weight of the vehicle body. Honda has developed an aluminum/steel sheet hybrid door that is more effective in reducing weight than an all-aluminum door. Because aluminum was used in the door skin, bimetallic corrosion at the connection between the aluminum and the steel sheets represented an issue. It was possible that the difference in the electrical potential of the two metals might promote corrosion at the connection between the aluminum door skin and the steel sheet door panel, in particular at the lower edge of the door, where rainwater and other moisture tend to accumulate, with the result that the appeal of the exterior of the door might decline.

Conventionally, the Ni-based superalloys NCF3015 (30Ni-15Cr) and the high nickel content NCF440 (70Ni-19Cr) (with its outstanding wear resistance and corrosion resistance), have been used as engine exhaust valve materials. In recent years, automobile exhaust gases have become hotter because of exhaust gas regulations and enhanced fuel consumption efficiency. Resource conservation and cost reductions also factor into global environmental challenges. To meet these requirements, NCF5015 (50Ni-15Cr), a new resource-conserving, low-cost Ni-based heat-resistant alloy with similar high-temperature strength and wear resistance as NCF440, has been developed. NCF5015's ability to simultaneously provide wear resistance, corrosion resistance and strength when NCF5015 is used with diesel engines was verified and the material was then used in exhaust valves.

At present, measurements of running resistance are conducted outdoors as a matter of course. Because of this, the ambient temperature at the time of the measurements has a considerable impact on the measurement data. The research discussed in this paper focused on the temperature characteristic of the tires and developed a new correction technique using a special rolling test apparatus. Specifically, using a tire rolling test apparatus that made it possible to vary the ambient temperature, measurements were conducted while varying the levels of factors other than temperature that affect rolling resistance (load, inflation pressure, and speed). Next, a regression analysis was applied to the data for each factor, and coefficients for a relational expression were derived, making it possible to derive a quadratic equation for the tire rolling resistance correction formula.

High viscosity index(HVI) petroleum base stock, with excellent temperature-viscosity characteristics, oxidation resistance, and low-evaporation properties, offers advantages as the base stock for high fuel economy engine oils, particularly because of its low-friction properties in the boundary and/or “E.H.L (Elastohydrodynamic Lubrication)” area due to its rheological characteristics. This research evaluated HVI base stock's low-friction properties. Upgrading the oil from 5W-30 to 5W-20 was also investigated. The friction properties of the HVI base stock were measured by a unit friction platform. The results show a 28% reduction in friction coefficient compared with the conventional, solvent refined oil, which is attributable to the high-pressure viscosity of the base oil.

In recent years, studies have been conducted on the relationship between the J factor, which indicates flow of molten aluminum at the time of injection, and the quality of HPDC products. The flow of molten metal at a high J factor is referred to as “Atomized Flow.” The authors and others conducted studies on the relationship between the J factor and the strength of HPDC products. An area exceeding 300MPa was found in the product produced at a high J factor corresponding to the “Atomized Flow.” The defect was less in the above-mentioned position because the gas porosity was finely dispersed. Considering that the fine dispersion of gas porosity is related to the “Atomized Flow”, pictures were taken to analyze “Atomized Flow.” The molten aluminum was ejected into an open space at a high speed and the splashed conditions were photographed. From the images taken by the pulse laser permeation, the conditions of microscopic atomized flow were observed precisely.

1 A new surface modification heat treatment technology called Wonder Process Craft which is different from plating and coating, was applied to the skirt section, which is the sliding surface of the piston in an internal combustion engine. This was intended to improve fuel economy and mechanical characteristics by reducing sliding resistance. In the application of solid lubrication, this treatment does not require the usage of binder, which was necessary for conventional coating, leading to the highest level achievable for the low sliding resistance effect inherent of solid lubrication. Since this treatment does not involve any change in significant dimensions, shapes, surface roughness, and so on, applying this treatment is easy. The persistence of the effect, productivity and recyclability of waste and emissions during treatment were also taken into account.

In order to reduce CO2 emissions from automobiles, a highly fuel-efficient hybrid vehicle, the “Insight”, has been developed at Honda. Life cycle CO2 emissions are compared for the aluminum-bodied Insight, a simulated steel-bodied Insight, and a conventional gasoline vehicle. Life cycle CO2 emission is still dominated by the in-use fuel consumption. However, the contribution of CO2 emission from material use and processing could increase when the vehicle fuel consumption is greatly reduced. The use of recycled aluminum reduces CO2 emission from the aluminum-bodied Insight.

The effects of aerodynamic coefficients on handling response and flat ride were quantified. For handling response, the aerodynamic effect was quantified by analysis with linear representation and a two-wheel simulation model, using aerodynamic coefficients obtained from a full scale car wind tunnel. The correlation of aerodynamic coefficients and handling response with driving feel was also ascertained. Aerodynamic yaw moment and side-force were also converted to equivalent front and rear lift to standardize aerodynamic indexes and improve aerodynamic development efficiency. For flat ride, steady and unsteady aerodynamic effects were quantified by analysis with a two-degree-of-freedom mass-spring-damper simulation model and aerodynamic coefficients obtained from a 35% scale model wind tunnel and towing tank test. Unsteady aerodynamic force occurrence mechanism was ascertained by unsteady CFD using dynamic mesh.

Vehicles are required durability in various environments all over the world. Especially water resistance on flooded roads is one of the important issues. To solve this kind of problem, a CFD technology was established in order to predict the water resistance performance of the vehicle at the early development stage. By comparison with vehicle tests on flooded roads, it is clarified the following key factors are required for accurate prediction; the vehicle velocity change, the vehicle height change and the air intake flow rate. Moreover, these three key factors should be appropriately determined from vehicle and engine specification to predict water intrusion for flooded roads at the early stage of development. In this paper, a methodology which determines appropriate analysis conditions mentioned above for flooding simulation from vehicle and engine specification is described. The methodology enables us to determine whether the vehicle provides sufficient waterproofness.

5 belt wind tunnels are the most common facility to conduct the experimental aerodynamics development for production cars. Among aerodynamic properties, usually drag is the most important development target, but lift force and its front/rear balance is also important for vehicle dynamics. Related to the lift measurement, it is known that the “pad correction”, the correction in the lift measurement values for the undesirable aerodynamic force acting on wheel belt surface around the tire contact patch, must be accounted. Due to the pad correction measurement difficulties, it is common to simply subtract a fixed amount of lift values from measured lift force. However, this method is obviously not perfect as the pad corrections are different for differing vehicle body shapes, aerodynamic configurations, tire sizes and shapes.

The International Lubricant Standardization and Approval Committee (ILSAC) ATF subcommittee members have compared the two oxidation bench test methods, Aluminum Beaker Oxidation Test (ABOT) and Indiana Stirring Oxidation Stability Test (ISOT), using a number of factory-fill and service-fill ATFs obtained in Japan and in the US. In many cases, the ATFs were more severely oxidized after the ABOT procedure than after the same duration of the ISOT procedure. The relative severity of these two tests was influenced by the composition of the ATFs. The bench test oxidation data were compared with the transmission and the vehicle oxidation test data.

According to some papers, the label fuel economy and the actual fuel economy experienced by the customers may exhibit a gap. One of the reasons may stem from the aerodynamic drag variations due to the natural wind. The fuel consumption is measured through bench test under several driving modes by using the road load as input condition. The road load is measured through the coast down test under less wind ambient conditions as determined by each regulation. The present paper aims to analyze the natural wind conditions encountered by the vehicle on public roads and to operate a comparison between the fuel consumptions and the driving energy. In this paper, the driving energy is calculated by the aerodynamic drag from the natural wind specifications and driving conditions. This driving energy and the fuel consumptions show good correlation. The fuel consumption is obtained from the vehicle Engine control unit(ECU) data.

The Honda NSX, made entirely of aluminum, introduces a concept of using chromium chromate as a method of chemical pretreatment. For other parts that contain a different type of metal, such as various parts of the chassis, a DACRO coating system as well as many other inventions are used. For the paint process itself, a new waterborne basecoat technology is also introduced to obtain a high-class appearance level for the NSX.

When using aluminum for vehicle body parts to reduce weight, the high pressure die casting (HPDC) is widely applied due to its adaptability to thin-wall products, near-net-shape castability, and short casting cycle time. Since a hollow construction is advantageous to increase stiffness of body parts, there has been a need of development of techniques for casting of hollow parts by HPDC. So far, hollow casting by HPDC has been realized for small parts using sand cores. When applying that method to large parts, however, it is necessary to increase filling speed. When the filling speed is increased, the core tends to break. In this project, we have developed a method to estimate changes of pressure distribution when filling molten metal by the casting simulation in order to analyze damages to the core. Through the analysis, we discovered occurrence of impulsive pressure waves.

EGR (Exhaust gas recirculation) can reduce the pumping loss and improve the thermal efficiency of spark ignition engines. The techniques for combustion enhancement under high EGR rate condition has been required for further improvement of the thermal efficiency. In order to develop the technique of combustion enhancement by turbulence, the influences of turbulence scale on combustion properties, such as probability of flame propagation, EGR limit of flame propagation, flame quenching and combustion duration were investigated under the condition of same turbulence intensity. Experiments were carried out for stoichiometric spherically propagating turbulent i-C8H18/Air/N2 flames using a constant volume vessel. It was clarified that all of these combustion properties were affected by the turbulence scale. The development of spherically propagating turbulent flame during flame propagation was affected by the turbulence scale.

A new type of lean NOx catalyst has been developed with improved thermal resistance. This lean NOx catalyst contains precious metals and NO2 adsorbents. The precious metals are used mainly for the oxidation reaction of NO, and the NO2 adsorbents are for the adsorption removal of generated NO2. The thermal resistance of the catalyst was raised by paying attention to the following points. 1) Improvement of thermal resistance for the NO oxidation activity by addition of a different precious metal element. 2) Prevention of thermal degradation of the NO2 adsorbent by addition of a new metal oxide. For item 1, Pd was added to the catalyst which had already included Pt. By having Pd coexist with Pt, the precious metal dispersion was kept high even after heat treatment, so the NO oxidizing ability was improved. For item 2, thermal degradation of NO2 adsorbent was prevented by addition of the new metal oxide (B) to the adsorbent.

There is a need to reduce vehicle's running resistance through aerodynamic performance in terms of having less negative impact on the global environment. In the Accord full model change, the package design is changed, so it is an opportunity to propose methods for improving aerodynamic performance. During the preliminary study, phenomenon analyses were conducted to identify areas that have a significant effect on aerodynamics by using a 25% scale model of the previous model. Based on more than 500 variation measurements as parameter study, the analysis was conducted using computational fluid dynamics (CFD). A proposal was made to the package design. For development that began with the fundamental frame proposed in preliminary studies, wind tunnel testing using 25% scale model was conducted jointly with the Styling Design Office to achieve enhancement styling while also increasing aerodynamic performance.

The change in the aerodynamic lift force (henceforth CL) by heave motion is discussed in this paper in order to clarify the effect of aerodynamic characteristics on the vehicle dynamic performance. We considered that phenomenon in actual car running at 160km/h and 1Hz heave frequency. Using a towing tank to change its water from the air to the working fluid to more easily observe this phenomenon. That makes possible to observe the same phenomenon with reduced velocity and small models under same Strouhal number condition. This method can be reducing vehicle speed to 3m/s (1/15 actual) and frequency to 0.2Hz (1/5 actual) in case using 40% scaled model. The results of these tests showed that unsteady CL is proportional to heave motion. These results showed the proportional relationship between unsteady CL and heave motion. The formularization of unsteady CL made it possible to introduce shape coefficients to vehicle dynamics simulations as functions of heave velocity.