Search Results

At present, biodiesel fuels using natural-origin materials are expanding in share, and there are many different kinds. Biodiesel fuel generates organic acid when it deteriorates, so care is needed when evaluating the influence of the fuel on automotive fuel-line materials. A model biodiesel fuel was designed taking into account deterioration of the fuel and mixing of impurities into it. Durability of automotive fuel-line rubber and plastic materials were evaluated by using the model fuel. From the evaluation results, it was found that fluoroelastomer (hereafter referred to as FKM) and polyacetal resin (hereafter referred to as POM) deteriorate depending on specific fuel properties and deterioration state. In this paper, we report evaluating results of biodiesel fuels on the automotive fuel-line rubber and plastic materials, and the importance of biodiesel fuel property management.

A second-generation power control unit (PCU) for a two-motor hybrid system is proposed. An optimally designed power module, which is a key component of the PCU, is applied to increase heat-resistant temperature, while the basic structure of the first generation is retained and the power semiconductor chip is directly cooled from the single side. In addition to the optimum design, by decreasing the power loss as well as increasing the heat-resistant temperature of the power semiconductors (IGBT: Insulated Gate Bipolar Transistor and FWD: Free Wheeling Diode), the proposed PCU has attained 25% higher power density and 23% smaller size compared to first-generation units, maintaining PCU efficiency (fuel economy). To achieve a high yield rate in the power module assembly process, a new screening technology is adopted at the initial stage of power module manufacturing.

Results are presented from an experimental study of the effects of engine speed and injection pressure transients on the cold start performance of a gasoline direct injection engine operating on iso-octane. The experiments are performed in an optically-accessible single-cylinder research engine modified for gasoline direct injection operation. In order to isolate the effects of the engine speed and injection pressure transients, three different cold start simulations are used. In the first cold start simulation the engine speed and injection pressure are constant. In the second cold start simulation the injection pressure is constant while the engine speed transient of an actual cold start is simulated. In the third cold start simulation both the engine speed and the injection pressure transients of an actual cold start are simulated.

Bio-ethanol is one of the candidates for automotive alternative fuels. For reduction of carbon dioxide emissions, it is important to investigate its optimum combustion procedure. This study has explored effect of ethanol fuels on HCCI-SI hybrid combustion using dual fuel injection (DFI). Steady and transient characteristics of the HCCI-SI hybrid combustion were evaluated using a single cylinder engine and a four-cylinder engine equipped with two port injectors and a direct injector. The experimental results indicated that DFI has the potential for optimizing ignition timing of HCCI combustion and for suppressing knock in SI combustion under fixed compression ratio. The HCCI-SI hybrid combustion using DFI achieved increasing efficiency compared to conventional SI combustion.

Power generation systems employed in small gas engine cogeneration were examined to compare losses in the converter, which converts three-phase alternator power to direct current (DC) voltage, and losses in the inverter, which converts power to high-quality alternating current (AC) voltage that can be connected into electric utility power lines. It is a characteristic of alternators that their efficiency and output voltage decline in the heavy load range. It was found, therefore, that step-down methods using thyristors operate in a low-efficiency range in order to provide a satisfactory supply of the targeted DC output voltage. Use of switching regulator methods, on the other hand, can generate the target voltage by regulating a switching device after first storing the alternator output in a choke coil. It was found, therefore, that these use the high-efficiency range of the alternator. The converter was found to have a resulting loss decrease of 19.4 W.

To increase energy utilization efficiency of a micro combined heat and power generation unit, methods for simultaneously enhancing efficiencies of power generation and of heat recovery, which are normally in the trade-off relationship has been studied. To increase power generation efficiency, an extended expansion linkage engine higher in thermal efficiency than conventional engines has been adopted. The power generation efficiency was enhanced by 3.8 points to 26.3% from 22.5% of a conventional model. However, since introducing an extended expansion engine increases kinetic energy and lowers the temperature of exhaust gas from the engine, it is difficult to enhance the heat recovery. Focusing on the fact that most released heat energy is discharged through ventilation from the unit, ventilation cooling system was reexamined, and reduction of the released heat energy was considered.

Bio-ethanol is used in many areas of the world as ethanol blended gasoline at low concentrations such as “E10 gasoline”. In this study, a method was examined to effectively use this small amount of ethanol within ethanol blended gasoline to improve thermal efficiency and high-load performance in a high-compression-ratio engine. Ethanol blended gasoline was separated into high-concentration ethanol fuel and gasoline using a fuel separation system employing a membrane. High-ethanol-concentration fuel was selectively used at high-load conditions to suppress knocking. In this system, a method to decrease ethanol consumption is necessary to cover the wide range of engine operation. Lower ethanol consumption could be achieved by Miller-cycle operation because decrease of the effective compression ratio suppresses knocking. However, high-load operation was limited due to the decrease in intake air volume with Miller-cycle operation.

Bio-ethanol is used worldwide in fuel mixtures such as E10 gasoline. In this study, an onboard fuel system employing a pervaporation membrane was investigated to separate E10 into high-octane-number fuel (high-concentration ethanol fuel) and low-octane-number fuel (low-concentration ethanol fuel). The optimal operation conditions and size of the membrane unit for the separation system were determined in consideration of the separation rate and vehicle installation. This system can supply separated ethanol with sufficient speed and quantity to improve engine performance under practical driving conditions. In addition, the study was conducted to confirm that separated fuels have properties sufficient for use in automobiles. This separation rate enabled 5-cycle-mode driving without temporary shortage of permeated fuel.

Owing to its combustion characteristics and chemical composition, natural gas features cleaner emissions and lower CO2 compared to gasoline under equal thermal efficiency. Natural gas can be a promising alternative energy source to respond to crude oil exhaustion and global warming issues. Focusing on the utility of natural gas, a feasibility study on CNG (Compressed Natural Gas) -fueled two-wheeled vehicles has been conducted. A proto-type two-wheeled vehicle was made based on a 125 cm3 class gasoline-fueled scooter. To adapt the engine to the use of CNG fuel, an electronically controlled gas injection system was applied to the fuel supply system. To provide abrasion resistance of engine valves and valve seats, the specific matter of gas-fuel was improved. Furthermore, a lubricant circulation passage was added to maintain the temperature of the pressure reducing valve.

This research sought to develop a dynamic charging system, achieving an unlimited EV cruising range by charging the EV at high power during cruising. This system would help make it possible to finish battery charging in a short time by contact with the EV while cruising and enable drivers to freely cruise their intended routes after charging. A simulation of dynamic charging conditions was conducted for ordinary autonomous cruising (i.e., ordinary EV cruising) when dynamically charging at a high power of 450-kW (DC 750 V, 600 A). This report discusses the study results of a method of building the infrastructure, as well as looking at the cruise test results and future outlook. In particular, the research clarified the conditions for achieving an unlimited vehicle cruising range with a 450-kW dynamic charging system. It also demonstrated that this system would allow battery capacities to be greatly reduced and make it possible to secure the battery supply volume and resources.

Adhesive bonding is a key technology for the lighter weight of battery pack trays using aluminum material. A robust design method of adhesive bonding with the required strength for battery pack structure after degradation was developed to minimize variability of strength under various noise conditions. The parameter design based on Taguchi methods determined the optimum adhesive condition of the bonding process. To guarantee strength after degradation, it is essential to select a robust adhesive material and to minimize the strength variation derived from the adhesive material. The functional evaluation, which includes experimental design method, determined adhesive material with the minimum strength variation among material candidates. Then, robustness of the adhesive material itself has been evaluated as the result of collaboration with the adhesive material supplier. This analysis was able to regulate the compound ratio of raw materials without reducing the adhesive strength.

By increasing the percentage of highly dissociative strong acid components included in the neutralizing acid of the electrodeposition coating, it was possible to improve electrical conductivity and coulomb efficiency and achieve excellent throwing power. The GA cratering caused by the increase in the strong acid ratio was resolved by setting the strong acid ratio to 90% while reducing MEQ. By increasing coulomb efficiency, the quantity of hydrogen gas produced during electrodeposition was minimized, and as a result, gas pinholes remaining in the coating were reduced, increasing the smoothness of the coating beyond than that of the current materials. As a result of this study, the usage of e-coating per vehicle body was reduced by approximately 11%.

One of the issues involved in compression ignition combustion is the increase in combustion noise from engine mechanical systems caused by rapid combustion. When the fuel used is natural gas, with its high ignition temperature, the compression is increased relative to gasoline, so that combustion becomes even more rapid. The present research pursues the issue of noise by clarifying the distinctive features of combustion noise through tests focused on the two topics of stroke-bore ratio (S/B ratio) and ignition timing for engine structures deformation mode. From these results, we verified combustion noise trend and occurrence factor.

Recently, the use of ethanol blended fuel is growing worldwide. Therefore, there is increasing needs for addressing issues relating to ethanol blended fuel use in gasoline engine fuel supply systems. In this paper, we focused on one of such issues, which is the reduced life of a multi-layered fuel filter used at inlet side of a fuel pump when it is used with ethanol blended fuel. In this study, we clarified that ethanol blended fuel tends to disperse dust particles contained in fuel to a greater extent than gasoline, and that it has a mechanism to accelerate clogging by concentrating the clogging only on the finest layer of the multi-layered filter. Also, in the process of clarifying this principle, we confirmed that dust particles dispersed by ethanol are coagulated when passing through the filter layers.

Various plant-derived alternative fuels have been proposed in recent years as ways to curb the global warming that occurs from the CO2 that is emitted by internal combustion engines. One such fuel is bioethanol. In Brazil, flexible fuel vehicles (FFV) are used that can run on blends from 100% hydrous ethanol (E100) to gasoline containing 22% ethanol (E22). This research addresses the optimal specifications of a FFV engine. FFV engines use E100 and E22 in any ratio. E100 has a very high RON of approximately 110, while that of E22 is low at approximately 95. The researchers considered these characteristics when selecting a compression ratio capable of providing good performance at any ethanol blend ratio. Additionally, ethanol is a single-component fuel without low-boiling-point components, so it has poor combustion at low temperatures. In general, FFV engines are often built with one intake valve to enhance product usability at low temperatures.

To enable a belt-driven Integrated Starter Generator (ISG) to be used in an idle-stop system, the belt system must be capable of both driving the accessories and of starting the engine. Conventional belt systems required a higher tension setting to accomplish this, and the associated increase in friction opposed the achievement of better fuel economy. In this research, an auto-tensioner with a contraction suppression function that utilizes the incompressibility of fluid as well as a belt system that enables the auto-tensioner to be optimally located were proposed. The behavior of the belt system was measured in detail by testing, and the cause of the fluctuation of the belt tension was clarified by analysis. A method of controlling the ISG torque to flatten out tension fluctuations was devised, and its effectiveness was confirmed by simulation and testing. From the overall results of the research, a belt system that does not require a high tension setting was realized.

Ultra-low energy consumption and ultra-low emission vehicle technologies have been developed by combining petroleum-alternative clean energy with a hybrid electric vehicle (HEV) system. Their component technologies cover a wide range of vehicle types, such as passenger cars, delivery trucks, and city buses, adsorbed natural gas (ANG), compressed natural gas (CNG), and dimethyl ether (DME) as fuels, series (S-HEV) and series/parallel (SP-HEV) for hybrid types, and as energy storage systems (ESSs), flywheel batteries (FWBs), capacitors, and lithium-ion (Li-ion) batteries. Evaluation tests confirmed that the energy consumption of the developed vehicles is 1/2 of that of conventional diesel vehicles, and the exhaust emission levels are comparable to Japan's ultra-low emission vehicle (J-ULEV) level.

Pre-ignition phenomena of methanol fuel (M85) and unleaded premium gasoline were studied with use of the post-ignition technique. The combustion pressure as well as a signal from the pre-ignition detector were analyzed. It was found that methanol fuel is more susceptible to pre-ignition compared to gasoline fuel. Large cycle-by-cycle variations are present with combustion by surface ignition at the time of pre-ignition. This was caused by wide variations in the 0% mass fraction burned point. Since ionization signals from the pre-ignition detector prior to spark ignition indicate the 0% mass fraction burned point by surface ignition, prediction of pre-ignition is possible with use of the post-ignition technique. Platinum tipped spark plugs were found to be highly susceptible to pre-ignition with methanol fuel.

The dynamic performance of battery electric vehicles (BEV) is affected by battery output power, which depends on state of charge (SOC) and the temperature of battery cells. The temperature of the batteries varies in particular with the environment, in which the user stores the vehicle, and the battery output power. It is therefore necessary to employ thermal management systems that can control the battery temperature within the optimal range under severely hot and cold conditions in BEVs. A highly sophisticated thermal management system and its operation strategy were developed to fulfill the above requirements. The powertrain components to be thermo-controlled were located into two coolant circuits having different temperature range. The compact and efficient front-end heat exchangers were designed to optimally balance the cooling performance of powertrain, cabin comfort, vehicle aerodynamics and the vehicle design.

Real-time simulation is a valuable tool in the design and test of vehicles and vehicle parts, mainly when interfacing with hardware modules working at a given rate, as in hardware-in-the-loop testing. Real-time operating-systems (RTOS) are designed for minimizing the latency of critical operations such as interrupt dispatch, task switch or inter-process communication (IPC). General-purpose operating-systems (GPOS), instead, are designed for maximizing throughput in heavy-load systems. In complex simulations where the amount of work to do in one step is high, achieving real-time depends not only in the latency of the event starting the step, but also on the capacity of the system for computing one step in the available time. While it is demonstrated that RTOS present lower latencies than GPOS, the choice is not clear when maximizing throughput is also critical.