Search Results

The constant velocity joint (CVJ) has seen increased usage driven by the growth of front wheel drive vehicles over the last 30 years. The CVJ provides a smooth, dynamic connection between the output of the axle or gearbox and the driving wheels of the vehicle. The seemingly simple device, however, requires specially designed greases to maximize protection of the internal components from distress and provide optimum performance and service life. One measure of potential distress in the CVJ can be related to temperature rise which is a reflection of the friction and wear properties of the grease employed. A test rig was designed and a method created to evaluate the temperature response of different greases used in a CVJ. The test rig was designed to allow a wide range of speeds, torques and shaft angles to be used. The rig uses a unique temperature pickup system to allow for dynamic measurement of the grease temperature in the boot.

A 100-hour engine dynamometer test for intake valve deposits (IVD) which uses a Ford 2.3L engine was developed by the Coordinating Research Council (CRC). Recently, this test has been approved by the American Society for Testing and Materials (ASTM) as Test Method D 6201-97. Since this test offers improvements in test variability, duration, and cost, it is expected to replace ASTM D 5500-94, a 16,000-km vehicle test run using a BMW 318i, as the key performance test for the Certification of Gasoline Deposit Control Additives by the EPA Final Rule. As a step in the replacement process, a correlation between valve deposit levels for the CRC 2.3L Ford IVD test and ASTM D 5500 BMW IVD test must be determined. This paper provides a statistical review of available data in an attempt to provide such a correlation.

This paper describes the development of an extended vane pump test procedure utilizing the Eaton® 35VQ-25 vane pump. Evaluation of two commercial Zinc Dithiophosphate containing and two commercial non Zinc (ashless) hydraulic fluids are also described. Results show that extending the test time allows differentiation among fluids which give comparable performance in the standard 50 hour test. System cleanliness, as well as pump weight loss, must be used in the performance assessment.

The popularity of light trucks and sport utility vehicles (SUVs), coupled with growing consumer demand for vehicles with more size, weight and horsepower, has challenged the original equipment manufacturers' (OEM) ability to meet the Corporate Average Fuel Economy (CAFE) specifications due to the increased contribution of these vehicle classes on fleet averages. The need for improved fuel economy is also a global issue due to the relationship of reduced fuel consumption to reduced CO2 emissions. Vehicle manufacturers are challenged to match the proper fluid with the application to provide the required durability protection while maximizing fuel efficiency. Recent new viscosity classifications outlined under SAE J306 aid in more tightly defining options for lubricant choice for a given application. Changes to the SAE J306 viscosity classification define new intermediate viscosity grades, SAE 110 and SAE 190.

Multifunctional or universal lubricating oils which service both gasoline and diesel engines have gained widespread commercial acceptance. Since 1970, numerous changes and additions have altered the performance tests and specifications which define the quality of these lubricants. New parameters include single cylinder and multicylinder diesel engine testing, valve train wear protection, clutch plate friction retention, extended drain interval and lubricant related fuel economy. In response to these requirements, new additive systems were developed. This paper discusses observed base oil-additive-engine test interactions and compares the performance of one of these additive systems to that of the old.

Light trucks and sport utility vehicles (SUVs) have become extremely popular in the United States in recent years, but this shift to larger passenger vehicles has placed new demands upon the gear lubricant. The key challenge facing vehicle manufacturers in North America is meeting government-mandated fuel economy requirements while maintaining durability. Gear oils must provide long-term durability and operating temperature control in order to increase equipment life under severe conditions while maintaining fuel efficiency. This paper describes the development of a full-scale light duty axle test that simulates a variety of different driving conditions that can be used to measure temperature reduction properties of gear oil formulations. The work presented here outlines a test methodology that allows gear oil formulations to be compared with each other while accounting for axle changes due to wear and conditioning during testing.

The Coordinating European Council, CEC, develops performance tests for the motor, oil, petroleum, additive and allied industries. In recent years, CEC has moved away from using round robin programmes (RRP's) for monitoring the precision and severity of test methods in favour of regular referencing within a test monitoring system (TMS). In a TMS, a reference sample of known performance, determined by cross-laboratory testing, is tested at regular intervals at each laboratory. The results are plotted on control charts and determine whether the installation is and continues to be fit to evaluate products. Results from all laboratories are collated and combined to monitor the general health of the test. The TMS approach offers considerable benefits in terms of detecting test problems and improving test quality. However, the effort required in collating data for statistical analysis is much greater, and there are technical difficulties in determining precision from TMS data.

The development of engine oil specifications in North America, Europe and Japan has resulted in a proliferation of performance tests of increasing complexity and cost. At the same time, the transportation industry is becoming more international with vehicle populations of mixed national origin the rule, rather than the exception. In this context, regional specification writing bodies are making efforts to rationalize their own specifications and to enter into dialogue with each other. Central to any attempt at rationalization, regionally or internationally, is the availability of high-quality reference oils. Data on two formulations (a passenger car motor oil and a heavy-duty engine oil) which have met major requirements of North American, European and Japanese engine builders are presented.

In this work, a novel bearing test rig was used to evaluate the impact of oil viscoelasticity on friction torque and oil film thickness in a hydrodynamic journal bearing. The test rig used an electric motor to rotate a test journal, while a hydraulic actuator applied radial load to the connecting rod bearing. Lubrication of the journal bearing was accomplished via a series of axial and radial drillings in the test shaft and journal, replicating oil delivery in a conventional engine crankshaft. Journal bearing inserts from a commercial, medium duty diesel engine (Cummins ISB) were used. Oil film thickness was measured using high precision eddy current sensors. Oil film thickness measurements were taken at two locations, allowing for calculation of minimum oil film thickness. A high-precision, in-line torque meter was used to measure friction torque. Four test oils were prepared and evaluated.

An ad hoc working group (WG) “AG1” was formed by ISO/TC22/SC34 [1] to conduct the necessary research to mitigate concerns with the prediction of lubricity in paraffinic diesel fuel (e.g., renewable diesel [RD] and gas-to-liquids [GTL] fuel), using ISO 12156-1 [2] high-frequency reciprocating rig (HFRR). Several field complaints had been raised regarding anomalies with HFRR readings of RDs not accurately predicting the lubricity of the fuel. Specific reports include readings below the 460 μm wear scar diameter (WSD) limit may still allow excessive scuffing and wear. Generally, for all fuels, there is a deterioration in precision (measurement error) in the 350 μm-500 μm range. The Paraffinic Diesel Fuel Lubricity AG1 was given the mandate to execute its work tasks comprising the below-listed deliverables while embracing the concept of continuous improvement.

Limited technical studies to speciate particulate matter (PM) emissions from gasoline fueled vehicles have indicated that the lubricating oil may play an important role. It is unclear, however, how this contribution changes with the condition of the lubricant over time. In this study, we hypothesize that the mileage accumulated on the lubricant will affect PM emissions, with a goal of identifying the point of lubricant mileage at which PM emissions are minimized or at least stabilized relative to fresh lubricant. This program tested two low-mileage Tier 2 gasoline vehicles at multiple lubricant mileage intervals ranging from zero to 5000 miles. The LA92 cycle was used for emissions testing. Non-oxygenated certification fuel and splash blended 10% and 20% ethanol blends were used as test fuels.

The continued development of more powerful aviation turbine engines has demanded greater thermal stability of the fuel as a high temperature heat sink. This in turn requires better definition of the thermal stability of jet fuels. Thermal stability refers to the deposit-forming tendency of the fuel. It is generally accepted that dissolved oxygen initiates the deposition process in freshly refined fuels. While there are many tests that are designed to measure or assess thermal stability, many of these either do not display sufficient differentiation between fuels of average stability (JP-8) and intermediate stability (JP-8+100, JP-TS), or require large test equipment, large volumes of fuels and/or are costly. This paper will discuss the use of three laboratory tests as “concept thermal stability prediction” tools with aviation fuels, including Jet A-1 or JP-8, under JP8+100 test conditions.

The Co-ordinating European Council (CEC) for the development of performance tests for transportation fuels, lubricants and other fluids has set up a working group to develop a laboratory pump rig test able to discriminate between diesel fuels of different lubricity performance. This test was expected to correlate with the performance of fuels and Fuel Injection Equipment (FIE) in the field, therefore providing a way to avoid costly field trials. This test could also enhance the understanding of the results from the High Frequency Reciprocating Rig (HFRR) method. The CEC working group was supported by representatives of Oil Companies, Test Houses, Additive Companies and all the European FIE Manufacturers. After a thorough investigative phase, the group focused on a Bosch VE 4 distributor-type pump run according to the Bosch WP2 test cycle. This choice was also widely accepted throughout the industry.

Phosphorus is known to reduce effectiveness of the three-way catalysts (TWC) commonly used by automotive OEMs. This phenomenon is referred to as catalyst deactivation. The process occurs as zinc dialkyldithiophosphate (ZDDP) decomposes in an engine creating many phosphorus species, which eventually interact with the active sites of exhaust catalysts. This phosphorous comes from both oil consumption and volatilization. Novel low-volatility ZDDP is designed in such a way that the amounts of volatile phosphorus species are significantly reduced while their antiwear and antioxidant performances are maintained. A recent field trial conducted in New York City taxi cabs provided two sets of “aged” catalysts that had been exposed to GF-4-type formulations. The trial compared fluids formulated with conventional and low-volatility ZDDPs. Results of field test examination were reported in an earlier paper (1).

Increasing vehicle efficiency has been one of the key drivers of the automotive industry worldwide due to new government emission legislations and rising fuel costs. While original equipment manufacturers (OEMs) are responding with innovative hardware designs for new models, lubricant companies are developing additive solutions to reduce frictional losses in the engine thereby increasing fuel economy of both new and existing vehicles. Fuel efficiency of the vehicle can be measured in a variety of driving cycles, including the New European Driving Cycle (NEDC), Japanese JC-08, and FTP-75 (Federal Test Procedure). The type of vehicle used in fuel economy evaluation in the same cycle plays a significant role. Fuel consumption rates for the same vehicle measured in these driving cycles vary due to the differences in the cycles. Thus, to assess the effect of the lubricant on fuel efficiency in various cycles, the fuel consumption is measured relative to a reference oil.

The popularity of SUVs and light trucks in North America, combined with the return to rear-wheel-drive cars globally, is significantly increasing the installation of torque control devices that improve vehicle stability and drivability. As with other driveline hardware, it is important to optimize the friction material-lubricant-hardware system to ensure that a torque control device provides consistent performance over the life of the vehicle. While there are many publications on friction tests relevant to automatic transmission fluids, the literature relating to torque control testing is not as well developed. In this paper, we will describe a split-mu vehicle test and the development of a split-mu screening test. The screening test uses the SAE#2 friction test rig and shows how results from this test align with those from actual vehicle testing.

Wet clutch friction devices are the primary means by which torque is transmitted in many of today's modern vehicle drivelines. These devices are used in automatic transmissions, torque vectoring devices, active on-demand vehicle stability systems, and torque biasing differentials. As discussed in a previous SAE paper ( 2006-01-3270 - Next Generation Torque Control Fluid Technology, Part I: Break-Away Friction Slip Screen Test Development), a testing tool was developed to simulate a limited slip differential break-away event using a Full Scale-Low Velocity Friction Apparatus (FS-LVFA). The purpose of this test was to investigate the fundamental interactions between lubricants and friction materials. The original break-away friction screen test, which used actual vehicle clutch plates and a single friction surface, proved a useful tool in screening new friction modifier technology.

Wet clutch friction devices are the primary means by which torque is transmitted through many of today's modern vehicle drivelines. These devices are used in automatic transmissions, torque vectoring devices, active on-demand vehicle stability systems and torque biasing differentials. As discussed in a previous SAE paper ( 2006-01-3271 - Next Generation Torque Control Fluid Technology, Part II: Split-Mu Screen Test Development) a testing tool was developed to correlate to full-vehicle split-mu testing for limited slip differential applications using a low speed SAE #2 friction test rig. The SAE #2 Split-Mu Simulation is a full clutch pack component level friction test. The purpose of this test is to allow optimization of the friction material-lubricant hardware system in order to deliver consistent friction performance over the life of the vehicle.

This paper features the results of emission tests conducted on diesel oxidation catalysts, and the combination of diesel oxidation catalysts and water blend fuel (diesel fuel continuous emulsion). Vehicle chassis emission tests were conducted using an urban bus. The paper reviews the impact and potential benefits of combining catalyst and water blend diesel fuel technologies to reduce exhaust emissions from diesel engines.

The Lubricant Test Monitoring System (LTMS) is the calibration system methodology and protocol for North American engine oil and gear oil tests. This system, administered by the American Society for Testing Materials (ASTM) Test Monitoring Center (TMC) since 1992, has grown in scope from five gasoline engine tests to over two dozen gasoline, heavy duty diesel and gear oil tests ranging from several thousand dollars per test to almost one-hundred thousand dollars per test. LTMS utilizes Shewhart and Exponentially Weighted Moving Average (EWMA) control charts of reference oil data to assist in the decision making process on the calibration status of test stands and test laboratories. Equipment calibration is the backbone step necessary in the unbiased evaluation of candidate oils for oil quality specifications.