Search Results

In this study both double and triple injection strategies were used with fuel pressures up to 300 and 250 MPa, respectively. Tests were conducted at medium load conditions with cooled, high-pressure EGR at a ratio of 40% and higher. A four-cylinder production engine, featuring double turbochargers with one variable geometry turbocharger, was tested. The double injection strategy consisted of a 20% close-coupled pilot injection while the triple injection strategy introduced a post injection consisting of 10% the total cycle fuel. Results of this study do not indicate an advantage to extreme fuel pressure. The increased air entrainment reduces soot while increasing the premixed burn heat release, mean cylinder temperature, and NOx. Compared to the double injection scheme, triple injections achieved much lower soot for the same EGR rate with only a small NOx penalty.

Second law analyses of both spark-ignition and diesel engines are presented using two-zone models. The analyses include descriptions of the evaluation of the various terms in the availability balance. Chemical and thermomechanical availability are separated using a definition which allows the portion of the fuel availability that can be extracted by a combustion engine to be distinguished from that which requires interaction with the reference environment. The chemical availability must be calculated correctly in order to obtain an availability balance. The diesel model includes a parameter that allows the effect of fuel-air mixing rates to be simulated. The analyses for the spark-ignition and diesel models are applied in a parametric study of the effects of equivalence ratio, fuel-air mixing, residual fraction and combustion duration on the chemical and thermomechanical availability and the irreversibility.

Particle Swarm and the Genetic Algorithm were coupled to optimize multiple performance metrics for the combustion of neat biodiesel in a turbocharged, four cylinder, John Deere engine operating under constant partial load. The enhanced algorithm was used with five inputs including EGR, injection pressure, and the timing/distribution of fuel between a pilot and main injection. A merit function was defined and used to minimize five output parameters including CO, NOx, PM, HC and fuel consumption simultaneously. The combination of PSO and GA yielded convergence to a Pareto regime without the need for excessive engine runs. Results along the Pareto front illustrate the tradeoff between NOx and particulate matter seen in the literature.

This paper describes the development of a thin-film optical sensor for measuring pH. The indicator behaves as a polyprotic acid with differing optical properties in each of its chemical forms. Together, these properties facilitate the development of an internally calibrated sensor by calculating the ratios of the absorption maximas for each form of the indicator. The covalent immobilization procedure developed demonstrated long term stability of 4 months without recalibration.

This work presents the analytic and experimental results relating engine performance and operating schedule with fuel cost and tail-pipe emissions for the series hybrid electric vehicle (HEV) design. Results are based on vehicle data from the electric G-van produced by Conceptor Industries. A computer simulation developed using basic principles predicts the battery demand over a specified vehicle operation profile. Engine tests on the effects of engine power level and number of starts show that while fuel consumption did not vary, carbon monoxide (CO) emissions did show an increase. The engine used was a 2-cylinder, spark ignited, 4-stroke, carbureted engine and did not utilize exhaust after-treatment. The results of the engine tests and simulation data are combined to predict the CO emissions and fuel cost for the series HEV design. The estimated CO output was 18.7 g/km, and the fuel cost was estimated between 4.3 and 4.5 cents/km.

An overview of the Iowa State Coal Project is presented. Draglines and scrapers are compared for energy efficiency in stripping coal. Survey results on scrapers are presented which show diverse production and cost relationships indicating that many factors other than size of machine, haul distance, and grade are important.

This paper gives a history of simulation of commercial vehicles, starting with the early models and progressing to today's multibody models. This is followed by a discussion of the key questions faced by simulators. Finally, the paper presents a new method to postprocess results through videoanimation.

This paper presents a review of our current experimental and theoretical understanding of icing feathers and the role that they play in the formation of ice accretions. It covers the following areas: a short review of past research work related to icing feathers; a discussion of the physical characteristics and terminology used in describing icing feathers; the presence of feathers on ice accretions formed in unswept airfoils, especially at SLD conditions; the role that icing feathers play in the formation of ice accretion shapes on swept wings; the formation of icing feathers from roughness elements; theoretical considerations regarding feather formation, feather interaction to form complex icing structures, the role of film dynamics in the formation of roughness elements and the formation of feathers. Hypotheses related to feather formation and feather growth are discussed.

Accurate quantification of 3D shapes of the complex ice structures accreted on wind turbine blades is highly desirable to develop ice prediction models for more accurate prediction of the aerodynamic performance degradation and power reduction due to the ice accretion on wind turbine blades. In the present study, an experimental investigation was conducted to quantitatively characterize the 3D shapes of the ice structures accreted over a DU91-W2-250 wind turbine airfoil model in the Icing Research Tunnel available at Iowa State University (ISU-IRT). A glaze icing condition and a rime icing condition that wind turbines usually experience in winter were duplicated by using ISU-IRT. A high-resolution non-intrusive 3D scanning system was used to make detailed 3D-shape measurements to quantify the complicated ice structures accreted on the wind turbine airfoil model as a function of the ice accretion time.

Numerical models were used to study the effects of dimethyl ether (DME) on the operation of a compression-ignition engine fueled with premixed natural gas. The models used multi-dimensional engine CFD coupled with detailed chemical kinetics. Combustion characteristics of various compositions of the natural gas and DME mixture were simulated. Results showed that combustion phasing, nitrogen oxides emissions, and effects of fuel compositions on engine operating limits were well predicted. Chemical kinetics analysis indicated that ignition was achieved by DME oxidation, which, in turn, induced natural gas combustion. It was found that low temperature heat release became more significant as DME concentration increased. For an appropriate amount of DME in the mixture, the stable engine operating range became narrower as natural gas concentration increased. The model also captured the low temperature combustion features of the present engine with low nitrogen oxides emissions.

Structures in cold weather environments are susceptible to atmospheric ice formation. A fracture mechanics based approach is proposed for in situ characterization of the interfacial fracture energy of ice on different substrates. This paper summarizes the development of the experimental and analytical framework to measure the ice adhesion energy, calibrated on static ice. The testing configuration utilizes a shaft-loaded blister test to produce stable crack propagation, from a well-defined pre-crack at the interface of the ice layer and the substrate. Measurements of the fracture energy are taken over a range of ice thicknesses and surface roughnesses. The developed analytical framework to estimate adhesion energy are verified and calibrated via finite element numerical simulation of the proposed geometric configuration and employing cohesive surfaces along the interface to simulate the crack nucleation and propagation process.

Understanding the fundamental details of drop/wall interactions is important to improving engine performance. Most of the drop-wall interactions studies are based on the impact of a single drop on the wall. To accurately mimic and model the real engine conditions, it is necessary to characterize spray/wall interactions with different impingement frequencies at a wide range of wall temperatures. In this study, a numerical method, based on Smoothed Particle Hydrodynamics (SPH), is used to simulate consecutive droplet impacts on a heated wall both below and above the Leidenfrost temperature. Impact regimes are identified for various impact conditions by analyzing the time evolution of the post-impingement process of n-heptane drops at different impingement frequencies and wall surface temperatures. For wall temperature below the Leidenfrost temperature, the recoiled film does not leave the surface.

Accurate modeling of evaporating sprays is critical for diesel engine simulations. The standard spray and evaporation models in KIVA-3V tend to under-predict the vapor penetration, especially at high ambient pressure conditions. A sharp decrease of vapor penetration gradient is observed soon after the liquid spray is completely evaporated due to the lack of momentum sources beyond the liquid spray region. In this study, a gas particle model is implemented in KIVA-3V which tracks the momentum sources resulting from the evaporated spray. Lagrangian tracking of imaginary gas particles is considered until the velocity of the gas particle is comparable to that of the gas phase velocity. The gas particle continuously exchanges momentum with the gas phase and as a result the vapor penetrations are improved. The results using the present gas particle model is compared with experimental data over a wide range of ambient conditions and good levels of agreement are observed in vapor penetration.

Numerical simulations were performed to investigate the combustion process in the Premixed Compression Ignition (PCI) regime in a light-duty diesel engine. The CHEMKIN code was implemented into an updated KIVA-3V release 2 code to simulate combustion and emission characteristics using reduced chemistry. The test engine used for validation data was a single cylinder version of a production 1.9L four-cylinder HSDI diesel engine. The engine operating condition considered was 2,000 rev/min and 5 bar BMEP load. Because high EGR levels are required for combustion retardation to make PCI combustion possible, the EGR rate was set at a relatively high level (40%) and injection timing sweeps were considered. Since injection timings were very advanced, impingement of the fuel spray on the piston bowl wall was unavoidable. To model the effects of fuel films on exhaust emissions, a drop and wall interaction model was implemented in the present code.

We are developing a drinking water test kit based on colorimetric-solid phase extraction (C-SPE) for use onboard the International Space Station (ISS) and on future Lunar and/or Mars missions. C-SPE involves measuring the change in diffuse reflectance of indicator disks following their exposure to a water sample. We previously demonstrated the effectiveness of C-SPE in measuring iodine in microgravity. This analytical method has now been extended to encompass the measurement of total I (i.e., iodine, iodide, and triiodide). This objective was accomplished by introducing an oxidizing agent to convert iodide and triiodide to iodine, which is then measured using the indicator disks previously developed for iodine. We report here the results of a recent series of C-9 microgravity tests of this method. The results demonstrate that C-SPE technology is poised to meet the total I monitoring requirements of the international space program.

New machinery and chemicals which are used to reduce the number of operations needed on the farm and the labor force required to perform them are reviewed from the point of view of the farmer. What types of power units and self-propelled equipment is the farmer interested in when he considers his purchase in the light of his net profits?

Various mixtures of ammonia (NH₃) and dimethyl ether (DME) were tested in a diesel engine to explore the feasibility of using ammonia as an alternative, non-carbon fuel to mitigate greenhouse gas emissions. The original diesel fuel injection system was replaced with a new system for injecting ammonia-DME mixtures into the cylinder directly. The injection pressure was maintained at approximately 206 bar for various fuel mixtures including 100% DME, 60%DME-40%NH₃, and 40%DME-60%NH₃ (by weight). As ammonia content was increased in the fuel mixture, the injection timing needed to be advanced to ensure successful engine operation. It was found that cycle-to-cycle variation increased significantly when 40%DME-60%NH₃ was used. In the meantime, combustion of 40%DME-60%NH₃ exhibited HCCI characteristics as the injection timing ranged from 90 to 340 before top-dead-center (BTDC). Emissions data show that soot emissions remained extremely low for the fuel mixtures tested.

Particulate matters, nitrogen oxides, and carbon monoxides emissions from large utility generators using diesel/biodiesel blends were measured. Stack measurements were performed on-site in a number of power plants by following the standard procedure of US EPA. The test engines were chosen to represent typical diesel engines used for electricity generation in the state. Tests were performed using the regular diesel fuel (B0), 10%, 20% and 100% biodiesel blends (B10, B20, B100). Test results showed that particulate matters and carbon monoxides decreased significantly as biodiesel content increases, whereas nitrogen oxides increased. Test results are consistent with other studies using mobile engines in the literature. Note that arbitrary changes in fuel or engine operating conditions are prohibited in power generation industry. Results of this study have been used by the state government to allow the use of biodiesel blends in stationary generators.

The simultaneous reduction of particulate matter (PM) and nitrous oxides (NOx) emissions form diesel exhaust is key to current research activities. Although various technologies have been introduced to reduce emissions from diesel engines, the in-cylinder reduction of PM and NOx due to improved combustion mechanisms will continue to be an important field in research and development of modern diesel engines. Furthermore increasing prices and question over the availability of diesel fuel derived from crude oil has introduced a growing interest. Hence it is most likely that future diesel engines will be operated on pure biodiesel and/or blends of biodiesel and crude oil-based diesel. In this study the performance of different biodiesel blends under low temperature combustion conditions (i.e., high exhaust gas recirculation and advanced fuel injection schemes) was investigated.

Effects of high injection pressure and converging nozzles on combustion and emissions of a multi-cylinder diesel engine were investigated. The engine uses a common-rail injection system that allows a maximum injection pressure of 200 MPa. Various injection pressures were tested to explore the benefits of high injection pressure in achieving low exhaust emissions in diesel engines. Injectors used in this study include conventional straight-hole nozzles and converging nozzles with a K factor of 3. Parametric studies were performed including variations in injection timings, number of injection pulses and EGR levels. It was found that low temperature combustion can be achieved by using high EGR with 1) late single injection or 2) double injection with an early pilot and a late main injection. Investigations revealed that high injection pressures significantly reduced soot emissions with an increase in NOx emissions under conventional injection timing ranges.