Search Results

This paper gives a history of simulation of commercial vehicles, starting with the early models and progressing to today's multibody models. This is followed by a discussion of the key questions faced by simulators. Finally, the paper presents a new method to postprocess results through videoanimation.

Accurate quantification of 3D shapes of the complex ice structures accreted on wind turbine blades is highly desirable to develop ice prediction models for more accurate prediction of the aerodynamic performance degradation and power reduction due to the ice accretion on wind turbine blades. In the present study, an experimental investigation was conducted to quantitatively characterize the 3D shapes of the ice structures accreted over a DU91-W2-250 wind turbine airfoil model in the Icing Research Tunnel available at Iowa State University (ISU-IRT). A glaze icing condition and a rime icing condition that wind turbines usually experience in winter were duplicated by using ISU-IRT. A high-resolution non-intrusive 3D scanning system was used to make detailed 3D-shape measurements to quantify the complicated ice structures accreted on the wind turbine airfoil model as a function of the ice accretion time.

This paper applies basic statistics to the simulation of vehicle dynamics in the time domain and the frequency domain. The methods presented here yield an expectation for the variation of the computed results as a function of variation in input parameters. Applications include important steady state measures of vehicle performance such as understeer gradient and yaw rate gain. Follow up analysis includes measures of transient response in the time domain and of amplitude and phase relationships in the frequency domain. There are several potential applications for this methodology, perhaps most important, an understanding of the consequences of parameter uncertainty on the credibility of simulated results.

This paper presents an analytical study of the performance improvements that can be obtained at both high and low speed using multiple steered axles on heavy articulated trucks. At high speed, rollover usually represents a worst case scenario. Therefore we have chosen to evaluate possible steering designs based on their ability to reduce lateral acceleration of the semitrailer center of gravity. This is in contrast to passenger cars where four-wheel steering has typically been evaluated based on measures that were thought to be related to driver acceptance. This paper also investigates the effects of steering rear tractor axles on the low-speed maneuverability of the vehicle. Steering algorithms for the rear tractor tires were evaluated using frequency response and simulation of an obstacle avoidance maneuver. Results indicate that at high speeds considerable reductions in trailer lateral acceleration can be obtained during transient maneuvers.

An explorative study was performed to demonstrate the feasibility of using a novel hybrid anti-/de-icing strategy for aircraft icing mitigation. The hybrid method was developed by combining the electro-thermal heating mechanism and specialized surfaces/coatings with different wettabilities. While an electrical film heater was utilized to provide thermal energy around the leading edge of a NACA0012 airfoil model, two different coating strategies, (i.e., (a). Superhydrophobic coating covering the entire airfoil surface to increase droplets bounce-off and accelerate surface water runback vs. (b). super-hydrophilic coating at the leading edge to increase evaporation area + superhydrophobic coating in downstream to prevent runback refreezing) were proposed and evaluated aiming at maximizing the anti-/de-icing efficiency of the hybrid method.

Elastic soft material/surface, such as Polydimethylsiloxane (PDMS), is a perspective, useful and low-cost hydrophobic and icephobic coating. While it has been reported to have good mechanical durability, its erosion durability under the high impacting of water droplets pertinent to aircraft inflight icing phenomena has not been explored. In this study, the droplet imping erosion characteristics of an icephobic PDMS surface/material is evaluated systematically upon the dynamic impinging of water droplets at different impact velocities (~ up to 75m/s), in comparison with other state-of-the-art icephobic materials/surfaces, such as superhydrophobic surface (SHS) and slippery liquid-infused porous surface (SLIPS). Surprisingly, the contact angle (CA) of the elastic PDMS is shown to have an over 20° increase (from 105° to 128°), which represents better hydrophobicity, after the erosion test which is mainly contributed to the higher roughness of the eroded PDMS surface.

An experimental study was conducted to investigate the dynamic ice accretion processes on bridge cables with different surface modifications (i.e., 1. Standard plain, 2. Pattern-indented surface, and 3. helical fillets). The icing experiments were performed in the unique Icing Research Tunnel available at Iowa State University (i.e., ISU-IRT). In order to reveal the transient ice accretion processes and the associated aerodynamic loadings on the different cable models under the different icing conditions (i.e., rime vs. glaze), while a high-speed imaging system was used to capture the transient details of the surface water transport and ice accretion over the cable surfaces, a high-accuracy dual-transducer force measurement system was also utilized to measure the aerodynamic loadings acting on the ice accreting cable models.

In the present study, an experimental investigation was conducted to characterize a hot-air-based anti-/de-icing system for the icing protection of aero-engine inlet guide vanes(IGVs). The experimental study was conducted in a unique icing research tunnel available at Iowa State University (i.e., ISU-IRT). A hollowed IGV model embedded with U-shaped hot-air flowing conduit was designed and manufactured for the experimental investigations. During the experiments, while a high-speed imaging system was used to record the dynamic ice accretion or anti-/de-icing process over the surface of the IGV model for the test cases without and with the hot-air supply system being turned on, the corresponding surface temperature distributions on the IGV model were measured quantitatively by using a row of embedded thermocouples.

Atmospheric icing poses a major threat to power transmission lines in cold regions. In the present study, an experimental investigation was conducted to examine the atmospheric icing process on high-voltage power transmission lines and characterize the effects of the ice accretion on the aerodynamic forces acting on the transmission lines. The experimental study was conducted in the Icing Research Tunnel available at Iowa State University (ISU-IRT). A cylinder model with the same diameter of commonly-used high-voltage power transmission lines (i.e., D = 29mm) is subjected to a typical glaze icing condition at an incoming wind speed of 20 m/s, a liquid water content (LWC) of 2.0 g/m3 and an ambient temperature of -5 0C. A high-resolution 3D scanner was used in the present study to extract the 3D shapes of the ice structures accreted over surface of the cylindrical test model as a function of the ice accretion time.

The promising anti-icing performance of the slippery liquid infused porous surface (SLIPS) has been recently demonstrated for various engineering applications. The runback icing for aircraft and wind turbines could be effectively mitigated considering the timely removal of water droplet by the wind shearing force due to the low adhesion on the SLIPS. In this study, the flow field both inside and around the wind-driven droplet over the SLIPS was experimentally investigated by using Particle Image Velocimetry (PIV) technique. Previous studies majorly focus on the internal flow pattern before the droplet incipient motion. In this study, the flow field inside a moving droplet was firstly investigated. As a result of the low surface adhesion of the SLIPS, droplet oscillations were eliminated and the droplet internal flow field could be corrected from the optical distortion.

The electro-thermal method is most commonly used for wind turbine anti-/de-icing. The upmost drawback of such systems is the high power consumption. In the present study, we proposed to use a durable slippery liquid-infused porous surface (SLIPS) to effectively reduce the power requirement of the heating element during the anti-/de-icing process. The explorative study was conducted in the Icing Research Tunnel at Iowa State University (ISU-IRT) with a DU91-W2-250 wind turbine blade model exposed under severe icing conditions. During the experiments, while a high-speed imaging system was used to record the dynamic ice accretion process, an infrared (IR) thermal imaging system was also utilized to achieve the simultaneous surface temperature measurements over the test model.