Search Results

In this study both double and triple injection strategies were used with fuel pressures up to 300 and 250 MPa, respectively. Tests were conducted at medium load conditions with cooled, high-pressure EGR at a ratio of 40% and higher. A four-cylinder production engine, featuring double turbochargers with one variable geometry turbocharger, was tested. The double injection strategy consisted of a 20% close-coupled pilot injection while the triple injection strategy introduced a post injection consisting of 10% the total cycle fuel. Results of this study do not indicate an advantage to extreme fuel pressure. The increased air entrainment reduces soot while increasing the premixed burn heat release, mean cylinder temperature, and NOx. Compared to the double injection scheme, triple injections achieved much lower soot for the same EGR rate with only a small NOx penalty.

Second law analyses of both spark-ignition and diesel engines are presented using two-zone models. The analyses include descriptions of the evaluation of the various terms in the availability balance. Chemical and thermomechanical availability are separated using a definition which allows the portion of the fuel availability that can be extracted by a combustion engine to be distinguished from that which requires interaction with the reference environment. The chemical availability must be calculated correctly in order to obtain an availability balance. The diesel model includes a parameter that allows the effect of fuel-air mixing rates to be simulated. The analyses for the spark-ignition and diesel models are applied in a parametric study of the effects of equivalence ratio, fuel-air mixing, residual fraction and combustion duration on the chemical and thermomechanical availability and the irreversibility.

Particle Swarm and the Genetic Algorithm were coupled to optimize multiple performance metrics for the combustion of neat biodiesel in a turbocharged, four cylinder, John Deere engine operating under constant partial load. The enhanced algorithm was used with five inputs including EGR, injection pressure, and the timing/distribution of fuel between a pilot and main injection. A merit function was defined and used to minimize five output parameters including CO, NOx, PM, HC and fuel consumption simultaneously. The combination of PSO and GA yielded convergence to a Pareto regime without the need for excessive engine runs. Results along the Pareto front illustrate the tradeoff between NOx and particulate matter seen in the literature.

This paper describes the development of a thin-film optical sensor for measuring pH. The indicator behaves as a polyprotic acid with differing optical properties in each of its chemical forms. Together, these properties facilitate the development of an internally calibrated sensor by calculating the ratios of the absorption maximas for each form of the indicator. The covalent immobilization procedure developed demonstrated long term stability of 4 months without recalibration.

HiSiMo cast irons are frequently used as material for high temperature components in engines as e.g. exhaust manifolds and turbo chargers. These components must withstand severe cyclic mechanical and thermal loads throughout their life cycle. The combination of thermal transients with mechanical load cycles results in a complex evolution of damage, leading to thermomechanical fatigue (TMF) of the material and, after a certain number of loading cycles, to failure of the component. In Part I of the paper, a fracture mechanics model for TMF life prediction was developed based on results of uniaxial tests. In this paper (Part II), the model is formulated for three-dimensional stress states, so that it can be applied in a post-processing step of a finite-element analysis. To obtain reliable stresses and (time dependent plastic) strains in the finite-element calculation, a time and temperature dependent plasticity model is applied which takes non-linear kinematic hardening into account.

HiSiMo cast irons are frequently used as material for high temperature components in engines as e.g. exhaust manifolds and turbo chargers. These components must withstand severe cyclic mechanical and thermal loads throughout their service life. The combination of thermal transients with mechanical load cycles results in a complex evolution of damage, leading to thermomechanical fatigue (TMF) of the material and, after a certain number of loading cycles, to failure of the component. In this paper (Part I), the low-cycle fatigue (LCF) and TMF properties of HiSiMo are investigated in uniaxial tests and the damage mechanisms are addressed. On the basis of the experimental results a fatigue life model is developed which is based on elastic, plastic and creep fracture mechanics results of short cracks, so that time and temperature dependent effects on damage are taken into account.

An investigation has been carried out to examine the influence of up to 300 MPa injection pressure on engine performance and emissions. Experiments were performed on a 4 cylinder, 4 valve / cylinder, 4.5 liter John Deere diesel engine using the Ricardo Twin Vortex Combustion System (TVCS). The study was conducted by varying the injection pressure, Start of Injection (SOI), Variable Geometry Turbine (VGT) vane position and a wide range of EGR rates covering engine out NOx levels between 0.3 g/kWh to 2.5 g/kWh. A structured Design of Experiment approach was used to set up the experiments, develop empirical models and predict the optimum results for a range of different scenarios. Substantial fuel consumption benefits were found at the lowest NOx levels using 300 MPa injection pressure. At higher NOx levels the impact was nonexistent. In a separate investigation a Cambustion DMS-500 fast particle spectrometer, was used to sample and analyze the exhaust gas.

Regulated and unregulated emissions (individual hydrocarbons, ethanol, aldehydes and ketones, polynuclear aromatic hydrocarbons (PAH), nitro-PAH, and soluble organic fraction of particulate matter) were characterized in engines utilizing duplicate ISO 8178-C1 eight-mode tests and FTP smoke tests. Certification No. 2 diesel (400 ppm sulfur) and three ethanol/diesel blends, containing 7.7 percent, 10 percent, and 15 percent ethanol, respectively, were used. The three, Tier II, off-road engines were 6.8-L, 8.1-L, and 12.5-L in displacement and each had differing fuel injection system designs. It was found that smoke and particulate matter emissions decreased with increasing ethanol content. Changes to the emissions of carbon monoxide and oxides of nitrogen varied with engine design, with some increases and some decreases. As expected, increasing ethanol concentration led to higher emissions of acetaldehyde (increases ranging from 27 to 139 percent).

Numerical models were used to study the effects of dimethyl ether (DME) on the operation of a compression-ignition engine fueled with premixed natural gas. The models used multi-dimensional engine CFD coupled with detailed chemical kinetics. Combustion characteristics of various compositions of the natural gas and DME mixture were simulated. Results showed that combustion phasing, nitrogen oxides emissions, and effects of fuel compositions on engine operating limits were well predicted. Chemical kinetics analysis indicated that ignition was achieved by DME oxidation, which, in turn, induced natural gas combustion. It was found that low temperature heat release became more significant as DME concentration increased. For an appropriate amount of DME in the mixture, the stable engine operating range became narrower as natural gas concentration increased. The model also captured the low temperature combustion features of the present engine with low nitrogen oxides emissions.

The impact of fuel droplets on heated surfaces is of great importance in internal combustion engines. In engine computational fluid dynamics (CFD) simulations, the drop-wall interaction is usually considered by using models derived from experimental data and correlations rather than direct simulations. This paper presented a numerical method based on smoothed particle hydrodynamics (SPH), which can directly simulate the impact process of fuel droplets impinging on solid surfaces. The SPH method is a Lagrangian meshfree particle method. It discretizes fluid into a number of SPH particles and governing equations of fluid into a set of particle equations. By solving the particle equations, the movement of particles can be obtained, which represents the fluid flows. The SPH method is able to simulate the large deformation and breakup of liquid drops without using additional interface tracking techniques.

This paper presents an analytical study of the performance improvements that can be obtained at both high and low speed using multiple steered axles on heavy articulated trucks. At high speed, rollover usually represents a worst case scenario. Therefore we have chosen to evaluate possible steering designs based on their ability to reduce lateral acceleration of the semitrailer center of gravity. This is in contrast to passenger cars where four-wheel steering has typically been evaluated based on measures that were thought to be related to driver acceptance. This paper also investigates the effects of steering rear tractor axles on the low-speed maneuverability of the vehicle. Steering algorithms for the rear tractor tires were evaluated using frequency response and simulation of an obstacle avoidance maneuver. Results indicate that at high speeds considerable reductions in trailer lateral acceleration can be obtained during transient maneuvers.

Understanding the fundamental details of drop/wall interactions is important to improving engine performance. Most of the drop-wall interactions studies are based on the impact of a single drop on the wall. To accurately mimic and model the real engine conditions, it is necessary to characterize spray/wall interactions with different impingement frequencies at a wide range of wall temperatures. In this study, a numerical method, based on Smoothed Particle Hydrodynamics (SPH), is used to simulate consecutive droplet impacts on a heated wall both below and above the Leidenfrost temperature. Impact regimes are identified for various impact conditions by analyzing the time evolution of the post-impingement process of n-heptane drops at different impingement frequencies and wall surface temperatures. For wall temperature below the Leidenfrost temperature, the recoiled film does not leave the surface.

Accurate modeling of evaporating sprays is critical for diesel engine simulations. The standard spray and evaporation models in KIVA-3V tend to under-predict the vapor penetration, especially at high ambient pressure conditions. A sharp decrease of vapor penetration gradient is observed soon after the liquid spray is completely evaporated due to the lack of momentum sources beyond the liquid spray region. In this study, a gas particle model is implemented in KIVA-3V which tracks the momentum sources resulting from the evaporated spray. Lagrangian tracking of imaginary gas particles is considered until the velocity of the gas particle is comparable to that of the gas phase velocity. The gas particle continuously exchanges momentum with the gas phase and as a result the vapor penetrations are improved. The results using the present gas particle model is compared with experimental data over a wide range of ambient conditions and good levels of agreement are observed in vapor penetration.

Numerical simulations were performed to investigate the combustion process in the Premixed Compression Ignition (PCI) regime in a light-duty diesel engine. The CHEMKIN code was implemented into an updated KIVA-3V release 2 code to simulate combustion and emission characteristics using reduced chemistry. The test engine used for validation data was a single cylinder version of a production 1.9L four-cylinder HSDI diesel engine. The engine operating condition considered was 2,000 rev/min and 5 bar BMEP load. Because high EGR levels are required for combustion retardation to make PCI combustion possible, the EGR rate was set at a relatively high level (40%) and injection timing sweeps were considered. Since injection timings were very advanced, impingement of the fuel spray on the piston bowl wall was unavoidable. To model the effects of fuel films on exhaust emissions, a drop and wall interaction model was implemented in the present code.

Experimental studies have shown that knitted wiremesh mixers reduce the formation of solid deposits and improve ammonia homogenization in automotive SCR systems. However, their implementation in CFD models remains a major challenge due to the complex WM geometry. It was the aim of the current study to investigate droplet WM interaction. Essential processes, such as secondary droplet generation, wall film formation, and heat exchange, were analyzed in detail and a numerical model was set up. A box with heat resisting glass was used to study urea-water solution spray impingement on a WM under a wide range of operating conditions. High speed videography was used to identify the impingement regimes. Infrared thermography was applied to investigate WM cooling. In order to determine the impact of the WM on the spray characteristics, the droplet spectrum was measured both upstream and downstream of the WM using the laser diffraction method.

A miniature sensor for detecting cylinder misfiring based on the principle of magnetostriction has been developed for on-board use in production vehicles. The sensor induces a magnetic field in the engine crankshaft, and via Faraday's law, obtains a signal directly related to the strength of the field. Due to magnetostriction, the field strength changes as the stress in the crankshaft changes during each cylinder firing. The output signal of the sensor is therefore high when any given cylinder fires and low when it misfires, permitting ready determination of misfiring. Tests on a manual transmission vehicle have shown that a single sensor can detect misfiring in one or more cylinders at any non-negative torque and any speed, as well as on very rough roads. Other uses for the sensor, such as knock detection, are anticipated.

Mean value engine model (MVEM) is the basis of control design for advanced internal combustion engines. The engine performance transient process usually takes a few cycles. The MVEM provides an adequate accurate description of the engine dynamics with reasonable approximation by ignoring the heat loss and sub-cycle events. MVEM is very important for engine system control development, especially when the modern engine becomes more and more complicated when equipped with throttle, turbocharger and after-treatment systems. Usually the MVEM is developed based on data from engine tests, which is a costly and time consuming process. In this paper, the air path MVEM modeling method based on the 1D detail model is discussed for a turbocharged diesel engine. Simulation is applied to demonstrate the effectiveness of this new method. This approach could be used to get the MVEM for control design even before the prototype engine is available.

This paper describes the advantage of the integrated simulation platform and presents the results of performance simulations and the feed-forward air-fuel ratio (AFR) controller design of a new concept stoichiometric compression ignition (SCI) engine based on this platform. In this integrated simulation environment, the SCI engine was modeled in GT-Power and a simplified production engine control module (ECM) is implemented in Simulink/Matlab for the performance simulation and AFR control. The integrated engine and controller model was used to investigate constant-speed load-acceptance (CSLA) performance. During performance simulation, searching for operating conditions is difficult but critical for performance analysis. Trial and error method would require a long time to do. Based on the integrated simulation, a proportional-integral (PI) controller was designed to find the accurate operating conditions.

New machinery and chemicals which are used to reduce the number of operations needed on the farm and the labor force required to perform them are reviewed from the point of view of the farmer. What types of power units and self-propelled equipment is the farmer interested in when he considers his purchase in the light of his net profits?

The winter of 2013-2014 provided an opportunity to operate off-road vehicles in cold weather for extended time as part of a vehicle/tier 4 diesel engine validation program. An unexpected area of study was the performance of high efficiency, on engine, fuel filters during continuous vehicle operation in cold weather. During the program we observed unexpected premature fuel filter plugging as indicated by an increase in pressure drop across the filter while in service. Field and laboratory testing was completed at John Deere and Donaldson to understand the cause of filter plugging. Although conditions were found where winter fuel additives could cause plugging of high efficiency filters, premature filter plugging occurred even when testing with #1 diesel fuel. This fuel contained no additives and was used at temperatures well above its cloud point.