Search Results

To meet corporate CO2 emission targets polymer composites are being explored for light-weighting vehicle applications. Operational requirements may demand that such materials function above glass transition temperatures or heat deflection points. Intumescent coatings are traditionally used in construction to protect steelwork during fire. This paper presents a novel experimental investigation of two intumescent technologies to thermally protect a reinforced polyamide, for use as a semi-structural vehicle component. Coatings were assessed against the thermal requirement to withstand 500°C for 10 minutes. The differences in performance observed between water and epoxy based coatings as well as when an insulation layer was introduced are reported. Ultimate Tensile Stress (UTS) and modulus values were obtained at −40°C, ambient, and 85°C for uncoated specimens before and after thermal cycling.

Testing real-time vehicular systems challenges the tester to design test cases for concurrent and sequential input events, emulating unexpected user and usage profiles. The vehicle response should be robust to unexpected user actions. Sequence Covering Arrays (SCA) offer an approach which can emulate such unexpected user actions by generating an optimized set of test vectors which cover all possible t-way sequences of events. The objective of this research was to find an efficient nonfunctional sequence testing (NFST) strategy for testing the robustness of real-time automotive embedded systems measured by their ability to recover (prove-out test) after applying sequences of user and usage patterns generated by combinatorial test algorithms, considered as “noisy” inputs. The method was validated with a case study of an automotive embedded system tested at Hardware-In-the-Loop (HIL) level. The random sequences were able to alter the system functionality observed at the prove-out test.

Market demand for high performance gasoline vehicles and increasingly strict government emissions regulations are driving the development of highly downsized, boosted direct injection engines. The in-cylinder temperatures and pressures of these emerging technologies tend to no longer adhere to the test conditions defining the RON and MON octane rating scales. This divergence between fuel knock rating methods and fuel performance in modern engines has previously led to the development of an engine and operating condition dependent scaling factor, K, which allows for extrapolation of RON and MON values. Downsized, boosted DISI engines have been generally shown to have negative K-values when knock limited, indicating a preference for fuels of higher sensitivity and challenging the relevance of a lower limit to the MON specification.

This paper presents a series of observations of time-averaged wake asymmetry for a range of “notchback” vehicle geometries. The primary focus is on a reduced scale experiment using full-sized saloon geometry. Substantial flow asymmetry was observed in the vehicle “notch”. Similar asymmetries are reported for a full scale experiment on the same geometry along with others as diverse as production models of a luxury and mid-sized saloon; basic car shapes and a simple body. In one case a physical explanation is proposed, based on the degeneration of an unstable symmetric wake structure.

2, 5-Dimethylfuran (DMF) has been receiving increasing interest as a potential alternative fuel to fossil fuels, owing to the recent development of new production technology. However, the influence of DMF properties on the in-cylinder fuel spray and its evaporation, subsequent combustion processes as well as emission formation in current gasoline direct injection (GDI) engines is still not well understood, due to the lack of comprehensive understanding of its physical and chemical characteristics. To better understand the spray characteristics of DMF and its application to the IC engine, the fuel sprays of DMF and gasoline were investigated by experimental and computational methods. The shadowgraph and Phase Doppler Particle Analyzer (PDPA) techniques were used for measuring spray penetration, droplet velocity and size distribution of both fuels.

With the growing complexity of, and reliance on, safety-related electrical/electronic (E/E) systems in the automotive sector, the development of an explicit safety case is highly recommended to provide assurance to the different stakeholders interested in automotive functional safety. The production of a safety case is explicitly mandated by the draft automotive functional safety standard ISO26262. A safety case should consider all organisational and technical factors that may contribute to safety. For example, it should provide assurance for the safe behaviours of a particular system as well as assurance for the process by which this system is developed, operated and maintained. In this paper, we address one component of the overall safety case, namely the assurance of the functional safety concept. In particular, we examine how model-driven development and assessment can provide a basis for the systematic generation of functional safety requirements.

The rotor and stator of electric motors consist of multiple materials, of which steel forms the majority of mass and volume. Steel in electric motors is commonly in the form of thin sheets (laminations), stacked along the axis of the rotor. The structural integrity of such a stack can be ensured using bolting, welding or bonding of the laminations. Predictive mechanical finite element simulations of these laminated stacks can become computationally intense because the steel sheets are thin, and the motor often contains hundreds of them. If the laminations are modelled individually, the size of the elements is very small compared to the overall dimensions and the interface between the laminations need to be modelled as well. In this paper, we present an alternate method of modelling this laminated stack as a single solid body using homogeneous and orthotropic material property, instead of representing each lamination.

Little research has been done on spray characteristics of 2,5-dimethylfuran (DMF), since the breakthrough in its production method as an alternative fuel candidate. In this paper, the spray characteristics of pure fuels (DMF, Isooctane) and DMF-Isooctane blends under different ambient pressures (1 bar, 3 bar and 7 bar) and injection pressures (50 bar, 100 bar and 150 bar) were studied using Phase Doppler Particle Analyzer (PDPA) and high speed imaging. Droplet velocity, size distribution, spray angle and penetration of sprays were examined. Based on the results, DMF had larger SMD and penetration length than isooctane. The surface tension of fuel strongly influenced spray characteristics. Increasing the surface tension by 26 % resulted in 12 % increase in SMD. Higher ambient pressure increased the drag force, but SMD was not influenced by the increased drag force. However, the increased ambient pressure reduced the injection velocity and We number resulting in higher SMD.

The increased application of lightweight materials, such as aluminium has initiated many investigations into new joining techniques for aluminium alloys. As a result, Self-piercing riveting (SPR) was introduced into the automotive industry as the major production process to join aluminium sheet body structures. Although both hydraulic and servo types of SPR equipment are used by the industry, the servo type is most commonly used in a volume production environment. This type uses stored rotational inertia to set the rivet. The initial rotational velocity of the mass dictates the setting force and hence the tool is described as velocity-controlled. A study was therefore conducted to examine the effect of setting velocity on the process including tooling and joint performance. It was found that the setting velocity would have a significant effect on tooling life. Over 80kN force could be introduced into the tooling depending on selection of the setting velocity.

Light weight alloys are widely used in the automotive industry in order to meet environmental requirements. Cast magnesium alloys are candidate materials due to their high strength to weight ratio, high stiffness and excellent castability. However, some previously reported anomalous cyclic stress-strain behaviours of magnesium alloys have not been fully investigated especially in LCF characterisation. The main objective of this work was to investigate the cyclic loading-unloading behaviour of high pressure die cast (HPDC) AM60B and AE44 magnesium alloys under uniaxial tension or/and compression and its effect on LCF behaviour. It was found that classical linear stress-strain behaviour, for both AM60B and AE44 alloys, applied only to a very small range of stress beyond which significant pseudo-elastic behaviour was discovered. This affected LCF characterisation and subsequent fatigue analysis processes.

Many electric (EV) and hybrid-electric (HEV) vehicles are designed to operate using only electric propulsion at low road speeds. This has resulted in significantly reduced vehicle noise levels in urban situations. Although this may be viewed by many as a benefit, a risk to safety exists for those who rely on the engine noise to help detect the presence, location and behaviour of a vehicle in their vicinity. In recognition of this, legislation is being introduced globally which will require automotive manufacturers to implement external warning sound systems. A key challenge for premium vehicle manufacturers is the development of a suitable warning sound signature which also conveys the appropriate brand aspirations for the product. A further major difficulty exists when trying to robustly evaluate potential exterior sounds by running large-scale trials in the real world.

The advent of 3D displays offers Human-Machine Interface (HMI) designers and engineers new opportunities to shape the user's experience of information within the vehicle. However, the application of 3D displays to the in-vehicle environment introduces a number of new parameters that must be carefully considered in order to optimise the user experience. In addition, there is potential for 3D displays to increase driver inattention, either through diverting the driver's attention away from the road or by increasing the time taken to assimilate information. Manufacturers must therefore take great care in establishing the ‘do’s and ‘don’t's of 3D interface design for the automotive context, providing a sound basis upon which HMI designers can innovate. This paper describes the approach and findings of a three-part investigation into the use of 3D displays in the instrument cluster of a road car, the overall aim of which was to define the boundaries of the 3D HMI design space.

Hardware-in-the-loop (HIL) simulations have long been used to test electronic control units (ECUs) and software in car manufacturers. It provides an effective platform to the rapid development process of the ECU control algorithms and accommodates the added complexity of the plant under control. Accurate Model based HIL simulation (AMHIL) is considered as a most efficient and cost effective way for exploration of new designs and development of new products, particularly in calibration and parameterization of vehicle stability controllers. The work presented in the paper is to develop a mathematical model of a windscreen wiper system for the purpose of conducting HIL vehicle test and eventually to replace the real component with the model for cost cutting and improved test efficiency. The model is developed based on the electro-mechanical engineering principles.

Complexity of electronics and embedded software systems in automobiles has been increasing over the years. This necessitates the need for an effective and exhaustive development and validation process in order to deliver fault free vehicles at reduced time to market. Model-based Product Engineering (MBPE) is a new process for development and validation of embedded control software. The process is generic and defines the engineering activities to plan and assess the progress and quality of the software developed for automotive applications. The MBPE process is comprised of six levels (one design level and five verification and validation levels) ranging from the vehicle requirements phase to the start of production. The process describes the work products to be delivered during the course of product development and also aligns the delivery plan to overall vehicle development milestones.

Car manufacturers put large efforts into reducing wind noise to improve the comfort level of their cars. Each component of the vehicle is designed to meet its individual noise target to ensure the wind noise passenger comfort level inside the vehicle is met. Sunroof designs are tested to meet low-frequency buffeting (also known as boom) targets and broadband noise targets for the fully open sunroof with deflector and for the sunroof in vent position. Experimentally testing designs and making changes to meet these design targets typically involves high cost prototypes, expensive wind tunnel sessions, and potentially late design changes. To reduce the associated costs as well as development times, there is strong motivation for the use of a reliable numerical prediction capability early in the vehicle design process.