Search Results

In this paper, the relationship was investigated between objective psychoacoustic parameters, A-weighted sound pressure level (SPL) and the results of the subjective evaluation by using grey relational analysis (GRA). The sounds were recorded with eight different passenger cars at four different running conditions. The sound quality indices were calculated, including loudness, sharpness, roughness, fluctuation, and A-weighted SPL. Subjective evaluation was performed by thirty subjects using rating scale method. GRA was compared with traditional correlation analysis, and the comparison shows that some hidden information which could not be found in the traditional correlation analysis was revealed. In order to know the further relationship between fluctuation and subjective evaluation, another subjective evaluation was performed by the same 30 subjects. The result demonstrates that the relationship revealed from GRA is correct.

Accurate sensing of road conditions is one of the necessary technologies for safe driving of intelligent vehicles. Compared with the structured road, the unstructured road has complex road conditions, and the response characteristics of vehicles under different road conditions are also different. Therefore, accurately identifying the road categories in front of the vehicle in advance can effectively help the intelligent vehicle timely adjust relevant control strategies for different road conditions and improve the driving comfort and safety of the vehicle. However, traditional road identification methods based on vehicle kinematics or dynamics are difficult to accurately identify the road conditions ahead of the vehicle in advance. Therefore, this paper proposes an unstructured road region detection and road classification algorithm based on machine vision to obtain the road conditions ahead.

It aims to study the unsteady flow characteristic of the side-view mirror wake field, and reduce the wind noise by means of unsteady flow control. In this paper, the PIV test in a wind tunnel is used to capture the unsteady flow in the wake field of the side-view mirror, which is used to verify the accuracy of the steady simulation method with RANS after being averaged. Then LES turbulence model is used to obtain the wind noise, and the unsteady flow characteristic like vortex shedding of the side-view mirror is studied. The results show that, in the wake of the side-view mirror, there is a vortex pair similar to Karman Vortex Street. In both horizontal and vertical sections, these two vortexes are respectively separated from the upper and lower edges of the side-view mirror. Accompanied by a significantly uncertain periodic shedding, they continue to extend back until dissipating.

Torsional vibration of drive shaft has great influence on the vibration of vehicle. Reasonable phase arrangement of multi-universal coupling can attenuate vibration. In this paper, theoretical model of drive shaft with planar multi-cross universal coupling was established; the optimization scheme of the phase arrangement of multi-cross universal coupling was presented. The results of test validation and simulation show that the optimization scheme is effective and reasonable. The results of test validation and simulation show that the optimization scheme was effective and reasonable and the optimized scheme could solve the abnormal vibration on floor. Arranging phases of universal joints reasonably is very significative for attenuate the torsional vibration of drive shaft and the floor vibration.

The buzz, squeak, and rattle (BSR) noise in the vehicle seat system is one of the most common vehicle interior noises. The presence of the BSR noise in the seat system may affect the riding experience and cause discomfort to the occupants. Therefore, the BSR issues have gradually attracted the attention of researchers. The main problem of BSR noise evaluation is how to quantify the noise signal to realize rapid evaluation. In this paper, the impact of rattle noise is studied in the vehicle seat system. Psychoacoustic metrics, which are commonly used in vehicle BSR noise evaluation, are calculated and compared to build a vehicle seat system evaluation model. To improve the accuracy of the model, the variational mode decomposition (VMD) method is applied to decompose the original noise signal into six Intrinsic Mode Functions (IMFs) and then the energy of each IMF is weighted by the kurtosis to obtain new characteristic parameters.

In order to improve ride comfort and reduce interior noise of commercial vehicles, modal sensitivity analysis and optimization design of a commercial vehicle cab was carried out, which increased the first natural frequency of the optimized cab by 23.96%. The result of cab modal test verified the correctness of the finite element model and the effectiveness of the improving method. The structure-acoustic coupling model of the cab was established, and the acoustic response of the coupled sound field was predicted. The sound pressure level of the optimized cab was reduced. In comparison of the optimized cab with the original one, the optimization scheme was confirmed to be effective and reasonable.

In recent years, the interior noise of automobile has been becoming a significant problem. In order to reduce the noise, porous materials have been widely applied in automobile manufacturing. In this study, the simulation method and optimal analysis are used to determine the optimum sound absorption of polyurethane foam. The experimental simulation is processed based on the Johnson-Allard model. In the model, the foam adheres to a hard wall. The incident wave is plane wave. The function of the model is to calculate the noise reduction coefficient of polyurethane foam with different thickness, density and porosity. The back propagation neural network coupled with genetic optimization technique is utilized to predict the optimum sound absorption. A developed back propagation neural network model is trained and tested by the simulation data.

Magneto-rhelological(MR) dampers are devices that use rheological fluids to modify the mechanical properties of fluid absorber. The mechanical simplicity, high dynamic range, large force capacity, lower power requirements, robustness and safe manner of operation have made MR dampers attractive devices for semi-active real-time control in civil, aerospace and automotive applications. Landing gear is one of the most essential components of the aircraft, which plays an extreme important role in preventing the airframe from vibration and excessive impact forces, improving passenger comfortable characteristics and increasing aircraft flight safety. In this paper, the semi-active system used in landing gear damping controller design, simulation, and the vibration test-bed are discussed and researched. The MR dampers employed in landing gear system were designed, manufactured and characterized as available semi-active actuators.

A vehicle vibration issue emerged for a hybrid prototype during low speed driving in EV mode. This work is focused on the effort to identify the root cause and resolve the issue. The endeavor begins by performing a motor test in moderate acceleration with an imposed constant torque load. All relevant information is simultaneously recorded, including vehicle speed, vibration of motor structure and seat track, motor rpm, voltage and current signals, etc. Then analyses are carried out to strive for a better understanding of the vibration characteristics and identify its mechanism. It is found that the torque ripple from the driving motor is the root cause of the low speed vehicle vibration in EV mode, and the torque ripple is found to be induced by the current distortion resulted from the current sensor drift and electromagnetic interference due to high current signals.

Aiming at the abnormal vibration of driver seat of a passenger car in idle condition, vibration acceleration of engine, frame and seat rail was tested to identify vibration sources. Order tracking and spectrogram analysis indicated that the second order self-excitation of engine was the main cause. To solve the problem, semi-active controlled hydraulic engine mount with air spring of which characteristics could shift between a high dynamic stiffness and a low one was applied. Then the structure and principle of the mount with variable characteristics was introduced and control mode was analyzed. Dynamic characteristics were obtained by bench test. With sample mount applied, vibration of seat rail was tested again in multiple vehicle and engine working conditions. Dates showed that abnormal vibration in idle condition was extremely reduced and the mount could also meet the requirement of engine to dynamic stiffness in driving conditions.

For the roll vibration problem of a Truck, a 4-DOF roll vibration model of its front suspension system was built. According to dynamics theory, the complex modal vibration modes of the model were all obtained. At the same time, the frequency response functions of frame roll angle acceleration, the relative dynamic load of wheel and the suspension dynamic deflection were respectively presented. Then their characteristics were respectively researched. In the process of characteristic analysis, a new system parameter was proposed, which is the space ratio of the space between suspensions of left and right sides and the wheel track of the front axle (space ratio in short). At last, the influence of system parameters on the vibration transmission property was also reserached, which included the natural frequency of the frame, the damping ratio, the stiffness ratio, the mass ratio, the rotational inertia ratio and the space ratio.

Intake system is an important noise source for commercial vehicles, which has a significant impact on their NVH performance. To predict the intake noise more accurately, a new one-dimensional prediction model is proposed in this paper. An air compressor model is introduced into the traditional model, and the acoustic properties of the intake system are simulated by GT-power. The simulation data of the inlet noise is obtained to make a comparison with the inlet noise data acquired from a test. The result shows that the proposed model can make a more precise prediction of the inlet noise. Compared with the traditional model, the proposed model can identify the noise coming from the air compressor, and achieve a more accurate prediction of the total sound pressure level of the inlet noise.

In the field of automatic driving, the combination of 3D LIDAR and inertial measurement unit (IMU) is a common sensor configuration scheme in laser point-cloud localization, high-precision map making and point-cloud target detection. So it is critical to calibrate LIDAR and IMU accurately. At present, due to the large volume and high cost of 3D LIDAR with high-line-number(Such as 64 lines or 128 lines), the configuration scheme of using multiple low-line-number 3D LIDARs appears in the automatic driving vehicle sensing system. However, the common calibration methods are not suitable for multi 3D LIDARs and IMU parameters calibration on autonomous vehicle, which have the disadvantages of cumbersome implementation and low accuracy. In this paper, a joint calibration test platform composed of dual LIDARs and IMU is assembled, and a method of precise automatic calibration based on GPS/RTK data is proposed.

This paper describes a novel recognition and classification method of vehicle targets in urban road based on a vehicle-mounted Velodyne HDL64E light detection and ranging (LIDAR) system. The autonomous vehicle will choose different driving strategy according to the surrounding traffic environments to guarantee that the driving is safe, stable and efficient. It is helpful for controller to provide the efficient stagey to know the exact type of vehicle around. So this method concentrates on reorganization and classification the type of vehicle targets so that the controller can provide a safe and efficient driving strategy for autonomous ground vehicles. The approach is targeted at high-speed ground vehicle, so real-time performance of the method plays a critical role. In order to improve the real-time performance, some methods of data preprocessing should be taken to simplify the large-size long-range 3D point clouds.

Air spring has a variable stiffness characteristic, its vibration frequency is much lower than that of leaf spring and will not vary with load of vehicle. More and more air springs are applied on automobile suspension. A study on the automobile ride comfort, and the controllability and stability about the bus with air suspension is performed in the paper, which is based on multi-body system dynamics.

The concept of “bionic design” has driven the developments of automotive design. In this paper, a novel beak-shaped automotive tail fin with honeycomb cellular structure is proposed based on the idea of “bionic design”. Beak-shaped appearance is utilized to meet the requirement of aerodynamics performance, inner honeycomb cellular structure is filled to achieve more lightweight space. This paper starts from the establishment of three dimensional (3D) model based on the real characteristics of sparrow’s beak. On this basis, aerodynamic performances of novel beak-shaped tail fin and conventional shark tail fin are analyzed by experiment. Finally, the stiffness and modal analyses of solid beak-shaped tail fin and honeycomb beak-shaped tail fin are carried out respectively. The results indicate that the deformation of solid beak-shaped tail fin and honeycomb beak-shaped tail fin satisfy the basic requirements.

In order to solve the abnormal vibration of a light bus, order tracking analysis of finite element simulation and road test was made to identify the vibration source, finding that the rotation angular frequency of the wheels and the first two natural frequency of the body structure overlaps, resonance occurring which lead to increased vibration. To stagger the first two natural frequency and excitation frequency of the body, thickness of sheet metal and skeleton of the body-in-white were chosen as the design variables, rise of the first two natural frequency of the body-in-white as the optimization objective, optimal design and sensitivity analysis of the body-in-white was carried out with the modal analysis theory. Combining with the modal sensitivity and mass sensitivity of sheet metal and skeleton, the optimum design was achieved and tests analysis was conducted.

In this research, the interior noise of a passenger car was measured, and the sound quality metrics including sound pressure level, loudness, sharpness, and roughness were calculated. An artificial neural network was designed to successfully apply on automotive interior noise as well as numerous different fields of technology which aim to overcome difficulties of experimentations and save cost, time and workforce. Sound pressure level, loudness, sharpness, and roughness were estimated by using the artificial neural network designed by using the experiment values. The predicted values and experiment results are compared. The comparison results show that the realized artificial intelligence model is an appropriate model to estimate the sound quality of the automotive interior noise. The reliability value is calculated as 0.9995 by using statistical analysis.

Improvement of shift quality evaluation has become more prevalent over the past few years in the development of automatic transmission electronic control system. For the problems of the subjective shift quality evaluation that subjectivity is too strong, the standard cannot be unified and the definition of the objective evaluation index is not clear at present, this paper studies on the methods of objective evaluation of shift quality based on the multi-hierarchical grey relational analysis. Firstly, objective evaluation index system is constructed based on physical quantities, such as the engine speed, the longitudinal acceleration of the vehicle and so on, which broadens the scope of the traditional objective evaluation index further.

Rattle noise as an error state of cabin noise in vehicles has become an important topic both in research and application. In engineering, the commonly used method to evaluate and detect rattle issues is greatly dependent on experts’ personal auditory perception. People judge a noise simply as “loud” and “not loud” or “qualified” and “unqualified.” A more objective method needs to be developed to eliminate the randomness of subjective evaluation. In this paper, a rig test of the seatbelt retractors was performed, and simulated random excitation was applied to the test samples through the MB vibration test bench in a semi-anechoic chamber. The rattle noises were recorded by HEAD SQuadriga II. Various methods were employed to identify and assess the severity of rattle noise on seatbelt retractors.