Search Results

This paper sets up a simplified dynamic model for simulating the yaw/roll stability of heavy tractor-semitrailer using Matlab/Simulink. A linear quadratic regulator (LQR) based on partial-state feedback controller is used to optimize the roll stability of the vehicle. The control objective for optimizing roll stability is to be reducing the lateral load transfer rate while keeping the suspension angle less than the maximum allowable angle. The simulation result shows that the LQR controller is effective in the active roll stability control of the heavy tractor-semitrailer.

Vehicle yaw stability control (YSC) can actively adjust the working state of the chassis actuator to generate a certain additional yaw moment for the vehicle, which effectively helps the vehicle maintain good driving quality under strong transient conditions such as high-speed turning and continuous lane change. However, the traditional YSC pursues too much driving stability after activation, ignoring the difference of multi-objective requirements of yaw maneuverability, actuator energy consumption and other requirements in different vehicle stability states, resulting in the decline of vehicle driving quality. Therefore, a vehicle yaw stability model predictive control strategy for dynamic and multi-objective requirements is proposed in this paper. Firstly, the unstable characteristics of vehicle motion are analyzed, and the nonlinear two-degree-of-freedom vehicle dynamics models are established respectively.

Vehicle Longitudinal Control (VLC) algorithm is the basis function of automotive Cruise Control system. The main task of VLC is to achieve a longitudinal acceleration tracking controller, performance requirements of which include fast response and high tracking accuracy. At present, many control methods are used to implement vehicle longitudinal control. However, the existing methods are need to be improved because these methods need a high accurate vehicle dynamic model or a number of experiments to calibrate the parameters of controller, which are time consuming and costly. To overcome the difficulties of controller parameters calibration and accurate vehicle dynamic modeling, a vehicle longitudinal control algorithm based on iterative learning control (ILC) is proposed in this paper. The algorithm works based on the information of input and output of the system, so the method does not require a vehicle dynamics model.

The mechanical properties of sandy road are quite different from those of hard surface road. For vehicle control systems such as EMS (engine management system), TCU (transmission control unit) and ABS (antilock brake system), the strategies and parameters set for solid surface road are not optimal for driving on sandy road. It is an effective way to improve the mobility of all-terrain vehicles by identifying sandy road online and shifting the control strategies and parameters of control systems to sandy sets. In this paper, a sandy road identification algorithm for SUVs is proposed. Firstly, the vehicle signals, such as engine torque and speed, gear position, wheel and vehicle speed, are acquired from EMS, TCU and ESP (electronic stability program) through CAN (controller area network) bus respectively. Based on the information and longitudinal force equilibrium equation, the travelling resistance of vehicle is estimated.

Lane-changing is a typical traffic scene effecting on road traffic with high request for reliability, robustness and driving comfort to improve the road safety and transportation efficiency. The development of connected autonomous vehicles with V2V communication provide more advanced control strategies to research of lane-changing. Meanwhile, four-wheel steering is an effective way to improve flexibility of vehicle. The front and rear wheels rotate in opposite direction to reduce the turning radius to improve the servo agility operation at the low speed while those rotate in same direction to reduce the probability of the slip accident to improve the stability at the high speed. Hence, this paper established Four-Wheel-Steering(4WS) vehicle dynamic model and quasi real lane-changing scenes to analyze the motion constraints of the vehicles.

This paper proposes a dynamic obstacle avoidance system to help autonomous vehicles drive on high-speed structured roads. The system is mainly composed of trajectory planning and tracking controllers. The potential field (PF) model is introduced to establish a three-dimensional potential field for structured roads and obstacle vehicles. The trajectory planning problem that considers the vehicle’s and tires’ dynamics constraints is transformed into an optimization problem with muti-constraints by combining the model predictive control (MPC) algorithms. The trajectory tracking controller used in this paper is based on the 7 degrees of freedom (DOF) vehicle model and the UniTire tire model, which was discussed in detail in previous work [25, 26]. The controller maintains good trajectory tracking performance even under extreme driving conditions, such as roads with poor adhesion conditions, where the car’s tires enter the nonlinear region easily.

A TCS strategy of electric vehicle with 4 in-wheel motors is proposed in this paper. The control method consists of three parts: target slip rate calculation, target torque calculation and coordination control. By using Lyapunov stability analysis algorithm, the target slip rate boundary which makes the system stable is obtained. The target torque of each wheel is calculated by PI controller. According to the engineering experience, the TCS coordinated control strategy under split friction coefficient (split-μ) road, and friction coefficient jump(μ jump) road is proposed. The test results show that this strategy can improve the acceleration comfort and yaw stability of vehicles on uniform low friction coefficient (low μ) , split-μ and μ jump road.

Omni-directional electric vehicle built by our research group is an advanced electric vehicle whose four wheels can drive, steer and brake independently. The vehicle chassis system is composed of four in-wheel motors, four independent steer motors and electromagnetic brake system, and its control system is divided into logical control layer and underlying execution layer. The information exchange between these two layers is implemented by CAN bus. In this paper, the traction control logic for Omni-directional electric vehicle is developed. The study mainly involves two aspects: the vehicle states estimation and the traction control logic design. The vehicle states, including vehicle longitudinal velocity, lateral speed, side slip angle and yaw rate, etc, are estimated based on Extended Kalman Estimation and multiple degrees of freedom vehicle model.

Steer-by-wire System is a new conception for steering system, which eliminates those mechanical linkages between hand steering wheel and front wheels, and communicates among the driver and wheels by signals and controllers. All these facilities improve the safety and conformability of the vehicle system and get rid of the mechanical constricts. This paper proposed three vehicle stability control strategies, including front wheel control, yaw rate feedback control and yaw rate& acceleration feedback control. We compared these three control methods by simulation and simulator tests. We also studied the integrated control algorithm of Steer-by-Wire System and 4WS, and compared with 2WS for SBW and the classical 4WS.

This paper summarized the development methodology and technical experiences on Formula Student racecar engines acquired by Jilin University from 2011 to 2015. This series of engines are all based on 600cc 4-cylinder motorcycle gasoline engines and were modified to turbocharged engines which met the Formula Student technical regulations, in order to achieve higher power output, wider torque band as well as lower fuel consumption. During the development process, multiple research projects have been conducted surrounding the turbocharging technology. These research projects have covered multiple areas including the matching of the flow rate characteristics of the engine and the turbocharger, the design of intake and exhaust systems, research on the wastegate as well as its actuator, the tuning and control of the boost pressure as well as the design of the lubrication system for the turbocharger, etc.

In this paper, in order to avoid the frequent switching of engine operating points and improve the fuel economy during driving, this paper proposes a control strategy for the 4-wheel drive (4WD) hybrid vehicle based on wavelet transform. First of all, the system configuration and the original control strategy of the 4WD hybrid vehicle were introduced and analyzed, which summarized the shortcomings of this control strategy. Then, based on the analyze of the original control strategy, the wavelet transform was used to overcome its weaknesses. By taking advantage over the superiority of the wavelet transform method in multi signal disposition, the demand power of vehicle was decomposed into the stable drive power and the instantaneous response power, which were distributed to engine and electric motor respectively. This process was carried out under different driving modes.

Embedded bus monitoring and fault diagnosis system, which was used on the hybrid vehicle was designed in this paper. And this system took the 32-bit embedded one as a hardware platform, customized a WinCE6.0 operation system and used EVC as the tool to design the embedded application. The functions of CAN communication, protocol defamations etc were realized. Good human-computer interaction is developed and the system has already been applied on the bus.

The traditional energy management algorithm is mainly based on a single driving cycle, it is obvious that many factors might be often neglected by designer, such as different driving cycles would suit for different control strategies. But they tend to make decisions on the balance of torque distribution and battery power that based on a single driving cycle. Therefore, it is very difficult to achieve the optimal control in each case. In this paper we introduce a new design concept of Multi-operating mode energy management, a mathematical model of the energy management applied to a hybrid vehicle system is presented. Results of simulations using the model with the Multi-operating mode energy management were compared with results of simulations using a model with the single mode energy management, allowing the energy efficiency evaluation of the proposed energy management system.

Based on traditional heavy commercial vehicles, a hydraulic hub-motor drive vehicle (HHMDV) is equipped with a set of hydraulic hub-motor auxiliary system (HHMAS) to improve the traction performance and adaptability under complex conditions. In the case of low-speed operation or mechanical transmission failure, the creep mode (CM) can be used to drive the vehicle. Aiming at a common hydraulic system problem that flow loss increases due to temperature variation, a temperature compensation control strategy of the CM is proposed in this paper. By analyzing the speed regulation characteristics of the closed loop of the system in the CM, combined with the efficiency of the hydraulic variable pump (HP) and the hydraulic quantitative motor (HM), and aiming at adjusting the engine work in the optimal curve of the engine, the temperature compensation factor is introduced to control the HP displacement with hydraulic stepless speed regulation.

Based on the traditional heavy commercial vehicle, hydraulic hub-motor drive vehicle (HHMDV) is equipped with a hydraulic hub-motor auxiliary drive system, which makes the vehicle change from the rear-wheel drive to the four-wheel drive to improve the traction performance on low-adhesion road. In the typical operating mode of the vehicle, the leakage of the hydraulic system increases because of the oil temperature rising, this makes the control precision of the hydraulic system drop. Therefore, a temperature compensation control strategy for the assist mode is proposed in this paper. According to the principle of flow continuity, considering the loss of the system and the expected wheel speed, the control strategy of multifactor target pump displacement based on temperature compensation is derived. The control strategy is verified by the co-simulation platform of MATLAB/Simulink and AMESim.

In this paper, based on the research of the first generation of a hybrid electric city bus, principle researches have been offered on the parameters matching of the power-train and main components for the new generation of hybrid electric city bus. The vehicle system was designed integrated, and then simulation platform was developed and established. The dynamic and economy performance can be predicted based on the above work, results show that the designed hybrid electric city bus can meet the performance demands and validate rationality of the parameters matching.

The motor errors of the four-wheel independent driving electric vehicles was studied, and classified as steady errors and dynamic errors. In the paper, the forward compensation control and the PID control strategy were respectively applied to compensate for the errors. The electric vehicles straight-line running stability caused by the motor errors was discussed, the PID control method based on BP neural net work was presented to co-ordinate torque of the wheels. The result of the simulation on the 7 degrees of freedom vehicle model showed that control method improved the straight-line running ability of the vehicle.

The ride comfort of heavy trucks is related to many factors, which include vehicle operating scenarios and vehicle structure parameters. An investigation of the influence of different factors on the ride comfort of heavy trucks was conducted. Based on the elastic theory of a uniform Euler-Bernoulli beam with both ends free, a 6 degree of freedom (DOF) half rigid-elastic vibration model of the vertical dynamic response was developed. The rigid-elastic model is more suitable to describe the actual movement of heavy trucks. The DOFs include vertical displacements of the body and each of two axles, the pitch displacement of the body, and the first and second order bending displacements of the body. The root mean square (RMS) values of body accelerations, dynamic deflections and relative dynamic loads form the evaluation index. Based on the rigid-elastic model, the influence of different factors on the ride comfort of heavy trucks is analyzed in the frequency domain.

A full drive-by-wire electric vehicle, named Urban Future Electric Vehicle (UFEV) is developed, where the four wheels' traction and braking torques, four wheels' steering angles, and four active suspensions (in the future) are controlled independently. It is an ideal platform to realize the optimal vehicle dynamics, the marginal-stability and the energy-efficient control, it is also a platform for studying the advanced chassis control methods and their applications. A centralized control system of hierarchical structure for UFEV is proposed, which consist of Sensor Layer, Identification and Estimation Layer, Objective Control Layer, Forces and Motion Distribution Layer, Executive Layer. In the Identification and Estimation Layer, identification model is established by utilizing neural network algorithms to identify the driver characteristics. Vehicle state estimation and road identification of UFEV based on EKF and Fuzzy Logic Control methods is also conducted in this layer.

In order to improve the tractive ability, steering capability and directional stability, etc. of automated mechanical transmission (AMT) vehicles running on the wet and slippery road, the anti-slip regulation (ASR) technologies for AMT vehicles are developed. The significance of ASR for AMT vehicles is introduced; a road friction recognition method based on the deceleration of driving wheels is investigated; a fuzzy anti-slip control system based on adjustment of engine torque is developed and the corresponding experimental verification is conducted. The experimental results denote that the proposed method is effective to eliminate the excessive slip when the AMT vehicle travels on the low friction road.