Search Results

This paper describes the experiments conducted to determine the effect of high energy multiple spark discharge (MSD) ignition systems and spark plug electrode design, on the cold start performance of a vehicle which was converted for dedicated operation on E85 (a blend of 85% ethanol and 15% gasoline) fuel. Tests were conducted using three different ignition configurations; original equipment manufacturer (OEM) ignition and spark plugs, high energy multiple spark discharge (MSD) ignition with OEM, J-type spark plugs, and high energy MSD ignition with surface gap electrode spark plugs. The high energy MSD ignition with OEM spark plugs showed a significant improvement in cold start performance over the OEM ignition. The addition of the surface gap spark plugs caused a decrease in cold start performance. Despite this, the surface gap spark plugs produced higher ending coolant temperature than the other configurations.

This paper describes experiments conducted to determine the effect of multiple spark discharge ignition systems and spark plug electrode design on cold start performance of a dedicated E85 fueled vehicle. Tests were conducted using three different ignition configurations: OEM ignition and spark plugs, multiple spark discharge ignition with OEM spark plugs, and multiple spark discharge ignition with large gap circular electrode spark plugs. The multiple spark discharge ignition with OEM spark plugs showed a significant improvement in cold start performance over the OEM ignition, but the addition of the circular electrode spark plugs caused a decrease in cold start performance. The circular ground spark plugs did produce a higher ending coolant temperature than either of the other configurations.

Kettering University's Clean Snowmobile Challenge student design team has developed a new robust and innovative snowmobile for the 2004 competition. Switching from the previous years four-stroke automotive engine, Kettering University has utilized a modified snowmobile in-line four cylinder, four-stroke, fuel- injected engine. This engine has been installed into a 2003 Yamaha RX-1 snowmobile chassis. Exhaust emissions have been minimized through the use of a customized catalytic converter and an electronically controlled closed-loop fuel injection system. A newly designed and tuned exhaust as well as several chassis treatments have aided in minimizing noise emissions.

Cylinder air/fuel ratio distribution is an important factor affecting the economy, power, vibration, and emissions of an internal combustion engine. Currently, production automobiles utilize an exhaust gas sensor located in the main exhaust stream in order to regulate air/fuel mixtures. By measuring the oxygen content of the exhaust gas for each cylinder independently, the degree of air/fuel variation between cylinders can be determined. This information can be used to determine the mixture quality of specific cylinders. Knowing these variances can lead to design changes in the intake and exhaust manifolds as well as better control of fuel metering which will improve the output of the engine. This study was carried out using a 1991 3.8L Buick V-6 engine with customized exhaust manifolds utilizing exhaust gas oxygen sensors for each cylinder in addition to the sensor located in the main combined exhaust gas stream. Production level, ZrO2 sensors were used for this experimental study.

Three-dimensional transient simulations using KIVA-3V were conducted on a 4-stroke high-compression ratio, methanol-fueled, direct-injection (DI) engine. The engine had two intake ports that were designed to impart a swirling motion to the intake air. In some cases, the intake system was modified, by decreasing the ports diameter in order to increase the swirl ratio. To investigate the effect of adding shrouds to the intake valves on swirl, two sets of intake valves were considered; the first set consisted of conventional valves, and the second set of valves had back shrouds to restrict airflow from the backside of the valves. In addition, the effect of using one or two intake ports on swirl generation was determined by blocking one of the ports.

A numerical study on the combustion of Methanol in a directly injected (DI) engine was conducted. The study considers the effect of the bowl-in-piston (BIP) geometry, swirl ratio (SR), and relative equivalence ratio (λ), on flame propagation and burn rate of Methanol in a 4-stroke engine. Ignition-assist in this engine was accomplished by a spark plug system. Numerical simulations of two different BIP geometries were considered. Combustion characteristics of Methanol under swirl and no-swirl conditions were investigated. In addition, the amount of injected fuel was varied in order to determine the effect of stoichiometry on combustion. Only the compression and expansion strokes were simulated. The results show that fuel-air mixing, combustion, and flame propagation was significantly enhanced when swirl was turned on. This resulted in a higher peak pressure in the cylinder, and more heat loss through the cylinder walls.

Numerical simulations of lean Methanol combustion in a four-stroke internal combustion engine were conducted on a high-compression ratio engine. The engine had a removable integral injector ignition source insert that allowed changing the head dome volume, and the location of the spark plug relative to the fuel injector. It had two intake valves and two exhaust ports. The intake ports were designed so the airflow into the engine exhibited no tumble or swirl motions in the cylinder. Three different engine configurations were considered: One configuration had a flat head and piston, and the other two had a hemispherical combustion chamber in the cylinder head and a hemispherical bowl in the piston, with different volumes. The relative equivalence ratio (Lambda), injection timing and ignition timing were varied to determine the operating range for each configuration. Lambda (λ) values from 1.5 to 2.75 were considered.

Three-dimensional numerical simulations of a diesel-fueled engine with a pre-chamber located in the cylinder head and a bowl in the piston were performed. The study considers the effect of diesel combustion in the pre-chamber on turbulence generation and hence fuel-air mixing and combustion in the piston-bowl. Diesel fuel was injected directly into the pre-chamber and the piston bowl at different times. In order to better determine the effect of pre-chamber combustion on the main chamber combustion, various pre-chamber injection timings were considered. The results show that pre-chamber combustion caused the average cylinder pressure to increase by up to 20% in some cases.

Much development in the automotive industry relates to the use of high-content ethanol blended fuels to reduce the emissions produced by on-road engines/vehicles. However, less research has been done on the effect of operating small off-road engines (SORE) on high-blend ethanol fuels without substantial modifications. Most manufacturers of such engines only certify proper operation on low content ethanol blends such as E10 (10% ethanol, 90% gasoline by volume). This paper focuses on the use of E77 fuel in a small off-road engine which is speed-governed. Such engines are commonly used in lawn mowers, small recreational vehicles, or other equipment. The exhaust emissions and performance of the engine were evaluated using the EPA 6-mode duty cycle for small recreational engines where testing and analysis followed the recommendations of SAE J1088. This test cycle consisted of operating the engine at steady state load points using a fixed engine speed.

Affordable clean snowmobile technology has been developed. The goals of this design included reducing exhaust emissions to levels which are below the U.S Environmental Protection Agency (EPA) 2012 standard. Additionally, noise levels were to be reduced to below the noise mandates of 78 dB(A). Further, this snowmobile can operate using any blend of gasoline and ethanol from E0 to E85. Finally, achieving these goals would be a hollow victory if the cost and performance of the snowmobile were severely compromised. Snowmobiling is, after all, a recreational sport; thus the snowmobile must remain fun to drive and cost effective to produce. The details of this design effort including performance data are discussed in this paper. Specifically, the effort to modify a commercially available snowmobile using a two cylinder, four-stroke engine is described. This snowmobile was modified to run on a range of ethanol blended fuels using a closed-loop engine control system.

Kettering University has developed a cleaner and quieter snowmobile using technologies and innovative methods which can be applied in the real world with a minimal increase in cost. Specifically, a commercially available snowmobile using a two cylinder, four-stroke engine has been modified to run on high-blend ethanol (E-85) fuel. Further, a new exhaust system which features customized catalytic converters and mufflers to minimize engine noise and exhaust emissions has developed. A number of additional improvements have been made to the track to reduce friction and diminish noise. This paper provides details of the snowmobile development the results of these efforts on performance and emissions. Specifically, the Kettering University snowmobile achieved reductions of approximately 72% in CO, and 98% in HC+NOx when compared with the 2012 standard. Further, the snowmobile achieved a drive by noise level of 73 dbA while operating on hard packed snow.

Kettering University's entry for the 2006 Clean Snowmobile challenge utilizes a Polaris FST Switchback. This snowmobile having a two cylinder, four-stroke engine has been modified to run on ethanol (E-85). The student team has designed and built a new exhaust system which features customized catalytic converters to minimize engine out emissions. A number of improvements have been made to the track to reduce friction and diminish noise.

Kettering University's Clean Snowmobile Challenge student design team has developed a new robust and innovative snowmobile for the 2005 competition. This snowmobile dramatically reduces exhaust and noise emissions and improves fuel economy compared with a conventional snowmobile. Kettering University has utilized a modified snowmobile in-line four cylinder, four-stroke, engine. The team added an electronically-controlled fuel-injection system with oxygen sensor feedback to this engine. This engine has been installed into a 2003 Yamaha RX-1 snowmobile chassis. Exhaust emissions have been further minimized through the use of a customized catalytic converter and an electronically controlled closed-loop fuel injection system. A newly designed and tuned exhaust as well as several chassis treatments have aided in minimizing noise emissions.

Clean snowmobile technology has been developed using methods which can be applied in the real world with a minimal increase in cost. Specifically, a commercially available snowmobile using a two cylinder, four-stroke engine has been modified to run on high-blend ethanol (E-85) fuel. Additionally, a new exhaust system which features customized catalytic converters and mufflers to minimize engine noise and exhaust emissions has developed. Finally, a number of additional improvements have been made to the track to reduce friction and diminish noise. The results of these efforts include emissions reductions of 94% when compared with snowmobiles operating at the 2012 U.S. Federal requirements.

A numerical and experimental study of the use of air motion control, piston bowl shape, and injector configuration on combustion and emissions in diesel engines has been conducted. The objective of this study is to investigate the use of flow control within the piston bowl during compression to enhance fuel air mixing to achieve a uniform air-fuel mixture to reduce soot and NO emissions. In addition to flow control different piston bowl geometries and injector spray angles have been considered and simulated using three-dimensional computational fluid dynamics and experiments. The results include cylinder pressure and emissions measurements and contour plots of fuel mass fraction, soot, and NO. The results show that soot and NO emissions can be reduced by proper flow control and piston bowl design.

A dimensionless relationship that estimates the maximum bearing load of a 4-cylinder 4-stroke in-line engine has been found. This relationship may assist the design engineer in choosing a desired counterweight mass. It has been demonstrated that: 1) the average bearing load increases with engine speed and 2) the maximum bearing load initially decreases with engine speed, reaches a minimum, then increases quickly with engine speed. This minimum refers to a transition speed at which the contribution of the inertia force overcomes the contribution of the maximum pressure force to the maximum bearing load. The transition speed increases with an increase of counterweight mass and is a function of maximum cylinder pressure and the operating parameters of the engine.