Search Results

The flow inside of an internal combustion engine is highly complex and varies greatly among different engine types. For a long time IC engine researchers have tried to classify the major mean flow patterns and turbulence characteristics using different measurement techniques. During the last three decades tumble and swirl numbers have gained increasing popularity in mean flow quantification while turbulent kinetic energy has been used for the measurement of turbulence in the cylinder. In this paper, simultaneous 3-D LDV measurements of the in-cylinder flows of the three different engines are summarized for the quantification of the flow characteristics. The ensemble averaged velocity, tumble and swirl motions, and turbulence kinetic energy during the intake and compression strokes were examined from the measured velocity data (approximately 2,000 points for each case) by the 3-D LDV system.

An experimental study is performed to investigate the effects of charge motion control on in-cylinder fuel-air mixture preparation and combustion inside a direct-injection spark-ignition engine with optical access to the cylinder. High-pressure production injector is used with fuel pressures of 5 and 10 MPa. Three different geometries of charge motion control (CMC) device are considered; two are expected to enhance the swirl motion inside the engine cylinder whereas the third one is expected to enhance the tumble motion. Experiments are performed at 1500 rpm engine speed with the variation in fuel injection timing, fuel pressure and the number of injections. It is found that swirl-type CMC devices significantly enhance the fuel-air mixing inside the engine cylinder with slower spray tip penetration than that of the baseline case without CMC device. Combustion images show that the flame growth is faster with CMC device compared to the similar case without CMC device.

The purpose of this work was to develop a fiber optic imaging system for use in flow visualization studies at the Michigan State University Engine Research Laboratory. A flexible fiber optic image carrier was coupled with a high speed rotating prism camera to create a unique imaging system which can easily reach remote location test sites. The flow visualization study was conducted on a motored 3.5 L four-valve engine test rig. A 40 watt pulsed copper vapor laser was synchronized with the camera to produce motion picture film at 5000 frames per second (fps). The image carrier which is attached to the camera contained an 80 degree field of view (FOV) tip adapter for viewing the entire cross-sectional area of the cylinder. The area imaged was a radial plane located 3 cm from the intake valves. The engine rig was motored at 850 rpm with a flow rate of 18 kg/hr. Entrained microballoon seeding particles were filmed as they traveled through the cylinder.

This paper reports the development of vapor/liquid visualization systems based on an exciplex (excited state complex) formed between dimethyl- or diethyl-substituted aniline and trimethyl-substituted naphthalenes. Quantum yields of individual monomers were measured and the exciplex emission spectra as well as fluorescence quenching mechanisms were analyzed. Among the many systems and formulations investigated in this study, an exciplex consisting of 7% 1,4,6-trimethylnaphthalene (TMN) and 5% N,N-dimethylaniline (DMA) in 88% isooctane was found to be the best system for the laser-induced exciplex fluorescence (LIEF) technique, which is used to observe mixture formation in diesel or spark ignition (SI) engines. Observation of spectrally separated fluorescence from monomer in the gas phase and from exciplex in the gasoline fuel [1] requires that the exciplex forming dopants have boiling points within the distillation range of gasoline (20 to 215°C).

Internal flow characteristics of a close coupled catalytic converter were examined by LDV measurements and high speed flow visualization. Although previous studies have been done on catalytic converters, they were conducted at steady state and using water flow seeded with a small quantity of tracer particles. The purpose of this study was to develop a better understanding of dynamic flows inside catalytic converters. The high speed flow visualization films and LDV results showed that areas of separation and circulation were present in the inlet region of the converter. Backflows into the neck of the converter were also observed. Each cylinder exhausted into a different region of the converter, with the front-middle region having the heaviest amount of flow. Large bursts of flow were created by each cylinder, while other regions of the inlet region showed backflows or very low flow rates. The midsection of the converter had a more uniform overall flow pattern.

National Accident Sampling System (NASS) data, for the years 1993-1995, suggests a high frequency of tibiofemoral joint fractures among automotive accident victims. In addition, the NASS data also suggests that these injuries may be attributable to direct axial loading via the floor pan and/or the foot controls. Hirsch and Sullivan (1965), and Kennedy and Bailey (1968) conducted quasi-static fracture experiments axially compressing human tibiofemoral joints at low rates of loading and low angles of flexion. Hirsch and Sullivan observed a mean fracture load of approximately 8 kN compared to approximately 16 kN in the Kennedy and Bailey study. The current tibiofemoral joint injury criterion used in anthropomorphic dummies is based on Hrisch and Sullivan''s data. The current study involved impact experiments on human tibiofemoral joints (aged 71.4±11.2) directed in a superior direction along the axis of the tibia with the joint flexed 90°.

A better understanding of turbulent kinetic energy is important for improvement of fuel-air mixing, which can lead to lower emissions and reduced fuel consumption. An in-cylinder flow study was conducted using 1548 Laser Doppler Velocimetry (LDV) measurements inside one cylinder of a 3.5L four-valve engine. The measurement method, which simultaneously collects three-dimensional velocity data through a quartz cylinder, allowed a volumetric evaluation of turbulent kinetic energy (TKE) inside an automotive engine. The results were animated on a UNIX workstation, using a 3D wireframe model. The data visualization software allowed the computation of TKE isosurfaces, and identified regions of higher turbulence within the cylinder. The mean velocity fields created complex flow patterns with symmetries about the center plane between the two intake valves. High levels of TKE were found in regions of high shear flow, attributed to the collisions of intake flows.

This work presents a method for simultaneously capturing visible and infrared images along with pressure data in an optical Diesel engine based on the International 4.5L VT275 engine. This paper seeks to illustrate the merits of each imaging technique for visualizing both in-cylinder fuel spray and combustion. The engine was operated under a part load, high simulated exhaust gas recirculation operating condition. Experiments examining fuel spray were conducted in nitrogen. Overlays of simultaneously acquired infrared and visible images are presented to illustrate the differences in imaging between the two techniques. It is seen that the infrared images spatially describe the fuel spray, especially fuel vapors, and the fuel mixing process better than the high-speed visible images.

In-cylinder flows in a motored four-valve SI engine were examined by simultaneous three-component LDV measurement. The purpose of this study was to develop better physical understanding of in-cylinder flows and quantitative methods which correlate in-cylinder flows to engine performance. This study is believed to be the first simultaneous three-component LDV measurement of the air flow over a planar section of a four-valve piston-cylinder assembly. Special attention is paid to the tumble formation process, three-dimensional turbulent kinetic energy, and measurement of the tumble ratio. The influence of the induction system and the piston geometry are believed to have a significant effect on the in-cylinder flow characteristics. Using LDV measurement, the flows in two different piston top geometries were examined. One axial plane was selected to observe the effect of piston top geometries on the flow field in the combustion chamber.