Search Results

Results of a recent low-speed wind-tunnel investigation conducted to define the forebody flow on a 16% scale model of the NASA High Angle-of-Attack Research Vehicle (HARV), an F-18 configuration, are presented with analysis. Measurements include force and moment data, oil-flow visualizations, and surface pressure data taken at angles of attack near and above maximum lift (36° to 52°) at a Reynolds number of one million based on mean aerodynamic chord. The results presented identify the key flow-field features on the forebody including the wing-body strake.

The ability of modern airplane surfaces to achieve laminar flow over a wide range of subsonic and transonic cruise flight conditions has been well-documented in recent years. Current laminar flow flight research conducted by NASA explores the limits of practical applications of laminar flow drag reduction technology. Past laminar flow flight research focused on measurements of transition location, without exploring the dominant instability(ies) responsible for initiating the transition process. Today, it is important to understand the specific causes(s) of laminar to turbulent boundary layer transition. This paper presents results of research on advanced devices for measuring the phenomenon of viscous Tollmien-Schlichting (T-S) instability in the flight environment. In previous flight tests, T-S instability could only be inferred from theoretical calculations based on measured pressure distributions.

The results of a design study of a Hybrid Laminar Flow Control (HLFC) wing at transonic speed and correlative studies for finite, swept supersonic wings are discussed in this paper. Transonic HLFC wing was designed such as to obtain laminar laminar flow on the the wing upper surface for X/C of 0.6 and with suction applied from the leading edge to 60% of the chord and with suction applied from just aft of the leading edge to twenty-five percent of the chord. New theoretical methods have been recently developed for predicting pressure distributions, supersonic wave drag and transition location for finite swept wings at transonic and supersonic Mach number conditions and are illustrative computations are given. Results for laminar and turbulent boundary-layer parameters consisting of the displacement effects and skin friction drag are also presented.

One of the factors needed to describe the wear behavior of the Space Shuttle Orbiter main gear tires is their behavior during the spin-up process. An experimental investigation of tire spin-up processes was conducted at the NASA Langley Research Center's Aircraft Landing Dynamics Facility (ALDF). During the investigation, the influence of various parameters such as forward speed and sink speed on tire spin-up forces were evaluated. A mathematical model was developed to estimate drag forces and spin-up times and is presented. The effect of prerotation was explored and is discussed. Also included is a means of determining the sink speed of the orbiter at touchdown based upon the appearance of the rubber deposits left on the runway during spinup.

A description is given of a computer program developed at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) for the assessment of manned space station environmental control and life support systems (ECLSS) technology. The program methodology along with the data base and mission model variables are given for 17 candidate technologies that show potential for supplying metabolic oxygen and water on manned space missions. The data base includes metabolic design loads associated with crew activity, engineering design parameters for each technology option, and cost data required for candidate life cycle cost comparisons. The method for ranking the candidate options in order to provide recommendations for space station application or subsequent development is presented.

An experiment was conducted to measure the surface pressures and sectional side forces on a 5° cone with three nose tips. The nose tips included a sharp, an 8.7% blunt, and a 17.5% blunt nose tip. Rings of pressure orifices were located at 40% and 80% of the model length and the model was rolled from ±180° in 9° increments to determine roll dependence. The sectional side force data for the sharp cone showed a strong dependence on the roll orientation of the model. The blunt nose cone configurations also showed a dependence on roll orientation. The blunt nose configurations were effective in reducing the sectional side force for angles of attack up to 25°. However, at angles of attack greater than 35°, the reduction was no longer significant. Pressure distributions for three angles of attack are presented to highlight details of the flow when: vortex asymmetries are just beginning; the vortices are in a steady asymmetric state; a vortex has shed between the 40% and 80% stations.

An investigation was conducted in the Langley 14- By 22-Foot Subsonic Tunnel to determine the low-speed aerodynamic characteristics of a powered generic NASP-like configuration in ground effect. The model was a simplified configuration consisting of a triangular wedge forebody, a rectangular mid-section which housed the propulsion simulation system, and a rectangular wedge aftbody. Additional model components included a delta wing, exhaust flow deflectors, and aftbody fences. Six-component force and moment data were obtained over an angle of attack range from −4° to 18° while model height above the tunnel floor was varied from 1/4 inch to 6 feet. Variations in freestream dynamic pressure, from 10 psf to 80 psf, and engine ejector pressure yielded a range of thrust coefficients from 0 to 0.8. Flow visualization was obtained by injecting water into the engine simulator inlets and using a laser light sheet to illuminate the resulting exhaust flow.

An investigation was conducted to determine the fore and aft elastic response characteristics and footprint geometrical properties of 30 × 11.5 −14.5, Type VIII, bias-ply and radial-belted aircraft tires. Stiffness and damping characteristics of each tire were obtained from load-deflection curves generated from static tests. Tire footprints were obtained for various vertical loads, and geometrical measurements were obtained from the resulting silhouettes. Results of this investigation show considerable differences in stiffness and damping characteristics between the bias-ply and radial-belted tire designs. Footprint geometrical data indicate that footprint aspect ratio effects may interfere with improved hydroplaning potential associated with the radial-belted tire operating at higher inflation pressures. Tire-wheel slippage problems encountered when testing the radial-belted tire design required special attention.

Seventeen Environmental Control and Life Support System technology options to provide metabolic oxygen and water to sustain a multiperson crew on Space Station missions have been evaluated. The options included state-of-the-art technologies as well as advanced technologies that offer the potential for improvements in Environmental Control and Life Support Systems performance. The methodology for candidate technology recommendations was based upon specific assessment criteria as functions of prelaunch development activities and postlaunch operational considerations. The electrochemical depolarized cell option for carbon dioxide concentration, the sabatier option for carbon dioxide reduction, the static feed water electrolysis option for metabolic oxygen recovery, and vapor compression distillation and multifiltration options for waste water recovery were recommended.

Tests with specially instrumented NASA B-737 and B-727 aircraft together with several different ground friction measuring devices have been conducted for a variety of runway surface types and wetness conditions. This effort is part of the Joint FAA/NASA Aircraft/Ground Vehicle Runway Friction Program aimed at obtaining a better understanding of aircraft ground handling performance under adverse weather conditions and defining relationships between aircraft and ground vehicle tire friction measurements. Aircraft braking performance on dry, wet, snow-, and ice-covered runway conditions is discussed together with ground vehicle friction data obtained under similar runway conditions. For a given contaminated runway surface condition, the relationship between ground vehicles and aircraft friction data is identified. The influence of major test parameters on friction measurements such as speed, test tire characteristics, and surface contaminant type are discussed.

A method for thermally analyzing convectively cooled flight experiments is presented in this paper. A three-dimensional fluid flow analysis code was used to optimize air circulation patterns and predict air velocities in thermally critical areas. A comparison between a fan flow analysis using this code and the performance characteristics of a typical isothermal free jet was made. The velocity profiles and radial distribution agree well for downstream mixing of the flow. Predicted air velocities from the fluid analysis were used to calculate forced convection coefficients for the flight experiment. These convection coefficients were used in a finite difference thermal analysis code to describe the response of air temperature and heat loss for the LIDAR Atmospheric Sensing Experiment (LASE) during transient flight profiles. The performance of the existing thermal design is described and the analytical techniques used to arrive at this design are presented.