Refine Your Search




Search Results

Technical Paper

Work Hardening and Strength Analysis of Steel Structure with Special Cross Section

This paper presents the results of a strength analysis of a newly developed steel structure featuring a special cross section achieved with the hydroforming process that minimizes the influence of springback. This structure has been developed in pursuit of further weight reductions for the steel body in white. A steel tube with tensile strength of 590 MPa was fabricated in a low-pressure hydroforming operation, resulting in thicker side walls. The results of a three-point bending test showed that the bending strength of the new steel structure with thicker side walls was substantially increased. A finite element crush analysis based on the results of a forming analysis was shown to be effective in predicting the strength of the structure, including the effect of work hardening.
Technical Paper

Warm-Up Characteristics of Thin Wall Honeycomb Catalysts

HC emission standards will be tightened during the 1990's in the US. A key issue in reducing HC emission is improving the warm-up characteristics of catalysts during the cold start of engines. For this purpose, studies are under way on reduction of heat mass of ceramic substrates. Reduction of cell walls in substrates to thickness smaller than the current thickness of 12mil or 6mil has resulted in reduced heat mass, and also reduced flow restriction of substrates. The warm-up characteristics of low bulk density catalysts are better than those of high bulk density, i.e., the warm-up characteristics of thinner wall or lower cell density catalysts are better than those of thicker wall or higher cell density catalysts. A relationship between geometric surface area and warm-up characteristics is observed.
Technical Paper

Virtual Occupant Model with Active Joint Torque Control for Muscular Reflex

Riding comfort on the seat is one of the important factors for vehicle comfort. To analyze riding comfort, there were some models for predicting human vibrations in the past studies. On the other hand, it is strongly affected by human body motion caused by vehicle excitation during driving especially low frequency, but it is difficult to predict human motion due to an unclear mechanism of muscle reflex. The purpose of this study is to construct virtual riding comfort testing simulation based on virtual prototyping of the seat. In this study, a virtual occupant model that predicts occupant motion on the seat against external excitation including muscle reflex for maintaining sitting posture constructed. The whole body was modeled as 15 segments biomechanical model (1D) with wobbling mass. Each joint has passive elastic torque and damping torque springs. Human body surface was modeled as rigid shape.
Journal Article

Verification of Flag Usage Patterns by Static Analysis Techniques

A flag is a global boolean variable used to achieve synchronization between various tasks of an embedded system. An application implementing flags performs actions or events based on the value of the flags. If flag variables are not implemented properly, certain synchronization related issues can arise which can lead to unexpected behavior or failure of the underlying system. In this paper, we present an automated verification technique to identify and verify flag usage patterns at an early stage of code development. We propose a two-step approach which consists of: a. identification of all potential flag variables and b. verification of flag usage patterns against predefined set of rules. The results of our experiment demonstrate that the proposed approach reduces the cost and complexity of the flag review process by almost 70%.
Technical Paper

Venturi Vacuum Transducer Enables Heavy EGR Control

In order to significantly reduce NOx levels by EGR (Exhaust Gas Recirculation), while maintaining good fuel economy and driveability, the EGR flow rate must be properly and accurately controlled under a variety of engine operating conditions. Toward this objective, a new EGR control system was developed. It utilizes a carburetor venturi vacuum for a stable reference signal that represents the engine operating condition and it controls the EGR flow rate by using a feedback principle to obtain sufficient flexibility compatible with several different engines. Its control characteristics were mathematically analyzed. And it has also been confirmed that the system can automatically compensate for the drift in EGR characteristics. This EGR control system has been utilized in Nissan’s emission control systems in order to comply with the 1978 Japanese Emission Standards and the 1980 U.S. Federal and California Emission Standards.
Technical Paper

Vehicle Cornering and Braking Behavior Simulation Using a Finite Element Method

This paper presents a vehicle dynamic simulation using a finite element method for performing more accurate simulations under extreme operating conditions with large tire deformation. A new hourglass control scheme implemented in an explicit finite element analysis code LS-DYNA(1) is used to stabilize tire deformation. The tires and suspension systems are fully modeled using finite elements and are connected to a rigid body that represents the whole vehicle body as well as the engine, drive train system and all other interior parts. This model is used to perform cornering and braking behavior simulations and the results are compared with experimental data. In the cornering behavior simulation, the calculated lateral acceleration and yaw rate at the vehicle's center of gravity agree well with the experimental results. Their nonlinear behavior is also well expressed.
Technical Paper

Variable Characteristic Permanent Magnet Motor for Automobile Application

This paper describes a variable magnetomotive force interior permanent magnet (IPM) machine for use as a traction motor on automobiles in order to reduce total energy consumption during duty cycles and cut costs by using Dy-free magnets. First, the principle of a variable magnetomotive force flux-intensifying IPM (VFI-IPM) machine is explained. A theoretical operating point analysis of the magnets using a simplified model with nonlinear B-H characteristics is presented and the results are confirmed by nonlinear finite element analysis. Four types of magnet layouts were investigated for the magnetic circuit design. It was found that a radial magnetization direction with a single magnet is suitable for the VFI-IPM machine. Magnetization controllability was investigated with respect to the magnet thickness, width and coercive force for the prototype design. The estimated variable motor speed and torque characteristics are presented.
Technical Paper

Validation of Wireless Power Transfer up to 11kW Based on SAE J2954 with Bench and Vehicle Testing

Wireless Power Transfer (WPT) promises automated and highly efficient charging of electric and plug-in-hybrid vehicles. As commercial development proceeds forward, the technical challenges of efficiency, interoperability, interference and safety are a primary focus for this industry. The SAE Vehicle Wireless Power and Alignment Taskforce published the Recommended Practice J2954 to help harmonize the first phase of high-power WPT technology development. SAE J2954 uses a performance-based approach to standardizing WPT by specifying ground and vehicle assembly coils to be used in a test stand (per Z-class) to validate performance, interoperability and safety. The main goal of this SAE J2954 bench testing campaign was to prove interoperability between WPT systems utilizing different coil magnetic topologies. This type of testing had not been done before on such a scale with real automaker and supplier systems.
Technical Paper

Validation of SID2s Dummy FE-Model and Study of Relation between Design Parameter and Injury

The accuracy of FE (Finite Element) side impact dummy characteristics is important when using FE vehicle model for vehicle development. This study evaluated the response characteristics of FE SID-lls dummy (5TH female) model that was developed by FTSS using FE code PAM-CRASH™. This paper will describe improvements of computational evaluation method and FE dummy model in the sled tests simulated interior. For the various impact conditions, good correlation between FE calculation and the sled test results was obtained.
Technical Paper

Using the Hybrid FE-SEA Model of a Trimmed Full Vehicle to Reduce Structure Borne Noise from 200Hz to 1kHz

The Hybrid FE-SEA method has been used to create fast/efficient model of structure-borne noise in a fully trimmed vehicle from 200Hz to 1kHz. A joint paper is presented which highlights the method and modelling process along with extensive validation results. This paper describes the use of the model to analyze structure borne noise in the full vehicle, design and evaluate the impact of counter-measures. One of the key attributes of the Hybrid FE-SEA method is the ability to predict noise transfer paths in the vehicle. First, results from a Noise Path Analysis are used to identify key contributors to interior noise in the 200Hz-1kHz frequency range. Next potential design strategies for reducing interior noise are introduced along with implications on the model. Finally, sample prediction results illustrating the impact of design changes on interior noise levels are shown along with preliminary experimental validation results.
Technical Paper

Usability Evaluation of Integrated Switch System

This paper describes an integrated switch system by which the audio control system, air-conditioner control system and navigation control system can be operated with a smaller number of switches. This system resolves several issues resulting from the incorporation of information technology into vehicles, including the increased visual load due to the greater amount of information presented and the poorer operability resulting from increased functionality. A usability evaluation was conducted and the results indicated that the integrated switch system can reduce visual load.
Technical Paper

Unsteady Pressure Analysis of the Wake Flow Behind a Passenger Car Model

This paper describes a system for measuring unsteady pressure at up to 256 spatial points and at frequencies up to 300 Hz. The system consists of commercially available equipment for measuring steady pressures. It is based on the use of electronically scanned pressure (ESP) sensors, 16 A/D converters, and a personal computer to control the whole system and acquire data. The signal outputs through the tubes connecting the pressure taps and the ESP sensors are compensated, as are the phase delays between the scanned signals and the gain variation. A 1/5 scale model of a sedan was used in this experiment. The passenger car model was placed in a wind tunnel equipped with a moving belt, which was operated at the same speed as the uniform flow in the wind tunnel. Pressure measurements were obtained at 252 points in a plane behind the model perpendicular to the uniform flow. Measurements were made with the belt turned on and off.
Technical Paper

Unregulated Emissions Evaluation of Gasoline Combustion Systems (Lean Burn / Stoichiometric DISI and MPI), State of the Art Diesel Aftertreatment Technologies (DPF, urea-SCR and DOC), and Fuel Qualities Effects (EtOH, ETBE, Aromatics and FAME)

In order to clarify future automobile technologies and fuel qualities to improve air quality, second phase of Japan Clean Air Program (JCAPII) had been conducted from 2002 to 2007. Predicting improvement in air quality that might be attained by introducing new emission control technologies and determining fuel qualities required for the technologies is one of the main issues of this program. Unregulated material WG of JCAPII had studied unregulated emissions from gasoline and diesel engines. Eight gaseous hydrocarbons (HC), four Aldehydes and three polycyclic aromatic hydrocarbons (PAHs) were evaluated as unregulated emissions. Specifically, emissions of the following components were measured: 1,3-Butadiene, Benzene, Toluene, Xylene, Ethylbenzene, 1,3,5-Trimethyl-benzene, n-Hexane, Styrene as gaseous HCs, Formaldehyde, Acetaldehyde, Acrolein, Benzaldehyde as Aldehydes, and Benzo(a)pyrene, Benzo(b)fluoranthene, Benzo(k)fluoranthene as PAHs.
Technical Paper

Uniform Quenching Technology by Using Controlled High Pressure Gas after Low Pressure Carburizing

To reduce quenching distortion, step gas quenching has been proposed in recent years, which refers to rapid gas cooling of steel from austenitizing temperature to a point above or below Ms temperature, where it is held for a specific period of time, followed by gas cooling. In this study, by using infrared thermography combined with conventional thermocouple, a new temperature monitoring and control system was developed to realize the step gas quenching process of a hypoid ring gear after low pressure carburizing. The test production results indicate that by using the new monitoring and control system, we can control the gas quenching process and the distortion of carburized gear treated by step gas quenching can be reduced significantly compared with standard gas quenching.
Technical Paper

Ultra-Clean Combustion Technology Combining a Low-Temperature and Premixed Combustion Concept for Meeting Future Emission Standards

Experimental investigations were conducted with a direct-injection diesel engine to improve exhaust emission, especially nitrogen oxide (NOx) and particulate matter (PM), without increasing fuel consumption. As a result of this work, a new combustion concept, called Modulated Kinetics (MK) combustion, has been developed that reduces NOx and smoke simultaneously through low-temperature combustion and premixed combustion, respectively. The characteristics of a new combustion concept were investigated using a single cylinder DI diesel engine and combustion photographs. The low compression ratio, EGR cooling and high injection pressure was applied with a multi-cylinder test engine to accomplish premixed combustion at high load region. Combustion chamber specifications have been optimized to avoid the increase of cold-start HC emissions due to a low compression ratio.
Technical Paper

Turbulence and Cycle-by-Cycle Variation of Mean Velocity Generated by Swirl and Tumble Flow and Their Effects on Combustion

Combinations of swirl flow and tumble flow generated by 13 types of swirl control valve were tested by using both impulse steady flow rig and LDV. Comparison between the steady flow characteristics and the result of LDV measurement under motoring condition shows that tumble flow generates turbulence in combustion chamber more effectively than swirl flow does, and that swirling motion reduces the cycle by cycle variation of mean velocity in combustion chamber which tends to be generated by tumbling motion. Performance tests are also carried out under the condition of homogeneous charge. Tumble flow promotes the combustion speed more strongly than expected from its turbulence intensity measured by LDV. It is also shown that lean limit air fuel ratio does not have a strong relation with cycle variation of mean velocity but with turbulence intensity.
Technical Paper

Trends in Vehicle Information Displays in the Multimedia Era

Flat panel displays for automobiles are facing a new era with the development of navigation systems. As navigation systems become more important as driver's assistance devices, development of birds-eye-view and 3D displays continues, as well as improvements for larger display screens and higher mounting positions. In response to the progress of mobile multimedia technologies, demands for larger display screens and larger aspect ratios have been increasing. Significance for improvements to anti-glare features or view angles has increased as they provide better visibility and the increase layout options. The use of human machine information interaction, which interfaces visual, audio and tactile senses, makes it possible to realize safer, more convenient and comfortable multimedia era vehicle
Technical Paper

Total Gas/Effective Fuel Ratio Predicts Coast Surge in Emission-Control Vehicles

In the course of developing a low-emission manual transmission vehicle, coast surge in the fore-and-aft direction resulting from the installation of certain emission-control devices was sometimes experienced immediately after the initiation of vehicle deceleration. Our investigation revealed that this vehicle surge was caused by combustion irregularities in a sequence of combustion-misfire-intense combustion events occurring every several cycles. A new combustibility standard. Gt/Feff, defined as the ratio of total cylinder mixture weight Gt to effective fuel weight Feff, was found to predict combustibility and irregular combustion over the entire mixture range. As a result, driveability during deceleration was improved by modifying key emission-control components.
Technical Paper

Three-Dimensional Computation of the Effects of the Swirl Ratio in Direct-Injection Diesel Engines on NOx and Soot Emissions

Three-dimensional computation has been applied to analyze combustion and emission characteristics in direct-injection diesel engines. A computational code called TurboKIVA was used to investigate the effects of the swirl ratio, one of the fundamental factors related to combustion control, on combustion characteristics and NOx and soot emissions. The code was first modified to calculate soot formation and oxidation and the precise behavior of fuel drops on the combustion chamber wall. As a result of improving calculation accuracy, good agreement was obtained between the measured and predicted pressure, heat release rate and NOx and soot emissions. Using this modified version of TurboKIVA, the effects of the swirl ratio on NOx and soot emissions were investigated. The computational results showed that soot emissions were reduced with a higher swirl ratio. However, a further increase in the swirl ratio produced greater soot emissions.
Technical Paper

Thermal Imaging Technology using a Thermoelectric Infrared Sensor

This paper describes a low-cost 48 × 48 element thermal imaging camera intended for use in measuring the temperature in a car interior for advanced air conditioning systems. The compact camera measures 46 × 46 × 60 mm. It operates under a program stored in the central processing unit and can measure the interior temperature distribution with an accuracy of ±0.7°C in range from 0 to 40°C. The camera includes a thermoelectric focal plane array (FPA) housed in a low-cost vacuum-sealed package. The FPA is fabricated with the conventional IC manufacturing process and micromachining technology. The chip is 6.5 × 6.5 mm in size and achieves high sensitivity of 4,300 V/W, which is higher than the performance reported for any other thermopile. This high performance has been achieved by optimizing the sensor's thermal isolation structure and a precisely patterned Au-black absorber that attains high infrared absorptivity of more than 90%.