Search Results

This paper describes a system for measuring unsteady pressure at up to 256 spatial points and at frequencies up to 300 Hz. The system consists of commercially available equipment for measuring steady pressures. It is based on the use of electronically scanned pressure (ESP) sensors, 16 A/D converters, and a personal computer to control the whole system and acquire data. The signal outputs through the tubes connecting the pressure taps and the ESP sensors are compensated, as are the phase delays between the scanned signals and the gain variation. A 1/5 scale model of a sedan was used in this experiment. The passenger car model was placed in a wind tunnel equipped with a moving belt, which was operated at the same speed as the uniform flow in the wind tunnel. Pressure measurements were obtained at 252 points in a plane behind the model perpendicular to the uniform flow. Measurements were made with the belt turned on and off.

In order to clarify future automobile technologies and fuel qualities to improve air quality, second phase of Japan Clean Air Program (JCAPII) had been conducted from 2002 to 2007. Predicting improvement in air quality that might be attained by introducing new emission control technologies and determining fuel qualities required for the technologies is one of the main issues of this program. Unregulated material WG of JCAPII had studied unregulated emissions from gasoline and diesel engines. Eight gaseous hydrocarbons (HC), four Aldehydes and three polycyclic aromatic hydrocarbons (PAHs) were evaluated as unregulated emissions. Specifically, emissions of the following components were measured: 1,3-Butadiene, Benzene, Toluene, Xylene, Ethylbenzene, 1,3,5-Trimethyl-benzene, n-Hexane, Styrene as gaseous HCs, Formaldehyde, Acetaldehyde, Acrolein, Benzaldehyde as Aldehydes, and Benzo(a)pyrene, Benzo(b)fluoranthene, Benzo(k)fluoranthene as PAHs.

A combined computational fluid dynamics (CFD) and finite element (FE) analysis approach has been developed to simulate in the early stages of design the temperature distribution and estimate the thermal fatigue life of an engine exhaust manifold. To simulate the temperature distribution under actual operating conditions, we considered the external and internal flow fields. Digital mock-ups of the vehicle and engine were used to define the geometry of the engine compartment. External-air-flow simulation using in-house CFD code was used to predict the flow fields in the engine compartment and the heat transfer coefficients between the air and the exhaust manifold wall at various vehicle speeds. Unsteady-gas-flow calculation using the STAR-CD thermal- fluids analysis code was to predict the heat transfer coefficients between the exhaust gas and the manifold wall under various operating conditions.

Nissan’s new 2.8 liter in-line 6-cylinder turbocharged engine was developed for Che Datsun 280ZX in order to achieve higher performance and improved fuel economy. The Electronic Concentrated Engine Control System (ECCS), controlled by microprocessor, is provided for this 2.8 liter turbocharged engine. ECCS controls fuel injection, ignition timing, EGR rate and idling speed. It solved the problems related to power and fuel economy by optimizing the control parameters. Further, this system contains a barometric pressure compensator and a detonation controller; thus, the performance of this engine is efficient over a wide range of circumstances and fuel octane ratings. During the development of the engine, computer simulation was employed to predict engine performance and select turbocharger size, valve timing and other important factors.

This Paper Presents the world's first active noise system for production vehicle implementation. Adopted in the new middle size FF car model, this epoch-making system dramatically reduces the booming noise caused by the second-order harmonic of engine revolution. This is accomplished by using an adaptive control theory based on digital signal processing technology and a digital signal processor (DSP). The system basically employs a multiple error filtered-x LMS algorithm, to which an new algorithm was added to achieve the maximum noise reduction effect under a condition of stable control in a compact system for production vehicle application.

The demands on valve seat insert materials, in terms of providing greater wear-resistance at higher temperatures, enhanced machinability and using non-environmentally hazardous materials at a reasonably low cost have intensified in recent years. Due therefore to these strong demands in the market, research was made into the possibility of producing a new valve seat insert material. As a result a high speed steel based new improved material was developed, which satisfies the necessary required demands and the evaluation trials, using actual gasoline engine endurance tests, were found to be very successful.

Generally, cobalt-contained sintered materials have mainly been applied for exhaust valve seat inserts (VSI). However, there is a trend to restrict the use of cobalt as well as lead environmental law, and cobalt is expensive. To solve these problems, a new exhaust VSI on the assumption of being cobalt and lead free, applicable for conventional engines, having good machinability, and with a reduced cost was developed. The new exhaust VSI is a material dispersed with two types of hard particles, Fe-Cr-C and Fe-Mo-Si, in the matrix of an Fe-3.5mass%Mo at the ratio of 15 mass % and 10 mass % respectively.

New image processing procedures for speckle photography and holographic interferometry are described. The algorithm for speckle photography measures the displacement value and direction automatically within the accuracy of ±5% over a range of 10 µm to 150 µm. This algorithm has adopted the Maximum Entropy Method to measure fringe intervals with high accuracy. The algorithm for holographic interferometry detects the fringe line and determines the displacement distribution with an operator's assist. Through the experiments, it was shown that these procedures are effective and accurate for vibration and deformation analysis.

New technologies are needed to reduce cold-start emissions in order to meet the more stringent regulations that will go into effect in Europe (EC2000 or EC2005) and in California (ULEV), especially for larger engines such as 6- and 8-cylinder units. One new technology in this regard is the electrically heated catalyst (EHC). However, the use of EHCs alone is not sufficient to achieve the necessary reduction in emissions. This paper discusses techniques for effectively combining the elements of an EHC system, including the introduction of secondary air into the exhaust, improved control of the air/fuel ratio, and an electric power supply method for EHCs. It is shown that it is more effective to promote exothermic reactions in the exhaust manifold than at the EHC. A suitable method for this purpose is to introduce secondary air into the exhaust near the exhaust valves.

Although automotive electronics was initially applied as a substitute for mechanical parts, this technology has the potential to achieve effective combinations of mechanical functions. A case in point is the successful resolution of fuel consumption and exhaust emission problems by effectively integrating engine control and catalyst technologies. LSI technology has also been incorporated into automotive electronics and established as a fundamental engine control tool. Thanks to LSI technology, particularly the use of microprocessor techniques, conventional machine design problems have been transformed into logical design ones. In the next stage of application, automotive electronics is expected to provide further benefits including a more comfortable ride, an improved human-machine system interface, and an advanced communications system between vehicles and other telecommunications stations.

This paper describes the numerical and experimental approaches that were applied to study swirl injectors that are widely used in direct-injection gasoline engines. As the numerical approach, the fuel and air flow inside an injector was first analyzed by using a two-phase flow analysis method [VOF (Volume of Fluid) model]. A time-series analysis was made of the flow though the injector and also of the air cavity that forms at the nozzle and influences fuel atomization. The calculated results made clear the process from initial spray formation to liquid film formation. Spray droplet formation was then analyzed with the synthesized spheroid particle (SSP) method. As the experimental approach, in order to measure the cavity factor that represents the liquid film thickness, nozzle exit flow velocities were measured by particle image velocimetry (PIV).

This paper presents a swiring flow type jet pump which has been developed and in put into practical use in transferring fuel between sumps in saddle-shaped fuel tanks. The pump is driven by the force of excess fuel returning from the engine. The major structural features of the pump are described along with its performance. Various problems encountered in the process of developing the pump are discussed along with the technologies developed to resolve them. Particular attention is focused on the effects that the geometries if the nozzle, throat and swirling groove have on fuel transfer efficiency. The results of experiments carried out to analyze these correlations are also presented.

Since a 4-valve engine is less flexible in the design and location of the intake ports as compared with a conventional 2-valve engine, there are some difficulties in strengthening the air motion, including swirl and turbulence, in order to achieve stable combustion under lean mixture operation. This study examined air motion imporvements of 4-valve engine that result in a stable combustion with a lean mixture. These improvements are brought about by the installation of a swirl control valve in each intake port. The results of this study have clarified that the lean stable limit was extended from an air-fuel ratio of 21.5 to 26.3 under a partial load, by optimizing the location and diameter of aperture of the swirl control valve.

Based on experimental analysis, the generation mechanism of abnormal exhaust noise which is characterized by an intermittent high frequency aetallic sound, is clarified by bench testing of a FWD vehicle. The noise is caused by large amplitude pressure waves (finite amplitude waves) in the exhaust pipe. They are amplified due to interference between reflected waves and subsequent waves from the engine, and are finally transformed into shock waves in the propagation process along the exhaust pipe, resulting in abnormal exhaust noise. By theoretical analysis of finite amplitude waves, the wave profile in the propagation process and the transition distance to the shock wave can be solved analytically where the assumptions of mass, momentum, and energy conservation are valid, until the moment of shock wave formation. The transition distance is a key parameter in analyzing the growth and existence of shock waves.

The Diesel Particulate Filter (DPF) system has been developed as one of key technologies to comply with tight diesel PM emission regulations. For the DPF control system, it is necessary to maintain temperature inside the DPF below the allowable service temperature, especially during soot regeneration to prevent catalyst deterioration and cracks. Therefore, the evaluation of soot regeneration is one of the key development items for the DPF system. On the other hand, regeneration evaluation requires a lot of time and cost since many different regeneration conditions should be investigated in order to simulate actual driving. The simulation tool to predict soot regeneration behavior is a powerful tool to accelerate the development of DPF design and safe regeneration control strategies. This paper describes the soot regeneration model applied to fuel additive and catalyzed types, and shows good correlation with measured data.

Three Japanese automobile manufacturers-Mitsubishi Motors Corp., Nissan Motor Co., Ltd., and Toyo Kogyo Co., Ltd.-have been making efforts over the past three years to design and develop effective thermal reactor-exhaust gas recirculation and catalytic converter systems suitable for small engines. The work is being done by members participating in the IIEC (Inter-Industry Emission Control) Program, and the exhaust emission levels of the concept vehicles developed by these companies have met the goal established by the IIEC Program at low mileage. Each system, however, has a characteristic relationship between exhaust emission level and loss of fuel economy. Much investigation is required, particularly with respect to durability, before any system that will fully satisfy all service requirements can be completed. This paper reports the progress of research and development of the individual concept vehicles.

The key-points in the diffusion bonding technique of green compacts during sintering, are the material compositions, which should be chosen according to their dimensional change during sintering, and the fitting clearance, which should be maintained in the range of press fit. Applying this technique, we have developed sinter-diffusion bonded idler sprockets for automotive engines by comfirming the bonding strength and torsional fatigue strength. And we also have developed a nondestructive analysis method for assuring the joint strength of idler sprockets in the mass production.

This paper describes simultaneous attainment in improving fuel consumption, output power and reducing HC emissions with a direct injection S.I. engine newly developed in Nissan. Straight intake port is adopted to increase discharge coefficient under WOT operation and horizontal swirl flow is generated by a swirl control valve to provide stable stratified charge combustion under part load conditions. As a result, fuel consumption is reduced by more than 20% and power output is improved by approximately 10%. Moreover, unburned HC is reduced by equivalently 30% in engine cold start condition. An application of diagnostic and numerical simulation tools to investigate and optimize various factors are also introduced.

This paper reports attempts to gain better understanding of the influence of bearing wear on the performance of hydrodynamically lubricated bearings. An analysis was carried out on bearings from a Sapphire bearing test rig using an elastohydrodynamic model. This involved the use of both the original and worn bearing surface profiles. The results indicated that bearing wear could improve the lubrication conditions. Also the progress of wear in the bearing was simulated using a simple model of the wear process. This model predicted that the wear would progress at a reducing rate. The predicted wear agreed well with measurements both in terms of the wear profile and the location of wear.

The effect of the introduction of low-emission vehicles on potential air quality improvement in the Los Angeles area was predicted using a three-dimensional airshed simulation model. The simulations were based on ozone concentration estimates made on the basis of data released by the California Air Resources Board concerning projected quantities of emissions from various sources in 2010. Analyses were made of three scenarios. One assumed that LEV, ULEV and ZEV regulations were enforced as planned, a second assumed that these planned regulations were modified; and a third assumed that emission levels from various sources were reduced in line with the goals of the Air Quality Management Plan formulated by the South Coast Air Quality Management District.