Search Results

A KIA Soul was instrumented to measure the relative velocity (magnitude and yaw angle) at the front of the vehicle and in-cabin sound at a location close to the side glass near the A-pillar vortex impingement. Tests were conducted at a proving ground under a range of conditions from low wind conditions (~3 m/s) to moderate (7-8 m/s) wind speeds. For any given set of atmospheric conditions the velocity and sound data at any given position on the proving ground were noted to be very repeatable, indicating that the local wakes dominated the "turbulent" velocity field. Testing was also conducted in an aeroacoustic wind tunnel in smooth flow and with a number of novel turbulence generating methods. The resulting sounds were analyzed to study the modulation at frequencies likely to result in fluctuation strength type noise.

Wind tunnels provide a convenient, repeatable method of assessing vehicle engine cooling, yet important draw-backs are the lack of a moving ground and rotating wheels, blockage constraints and, in some tunnels, the inability to simulate ambient temperatures. A series of on-road and wind-tunnel experiments has been conducted to validate a process for evaluating vehicle cooling system performance in a high blockage aerodynamic wind tunnel with a fixed ground simulation. Airflow through the vehicle front air intake was measured via a series of pressure taps and the wind-tunnel velocity was adjusted to match the corresponding pressures found during the road tests. In order to cope with the inability to simulate ambient temperatures, the technique of Specific Dissipation (SD) was used (which has previously been shown to overcome this problem).

Vehicles produced in decades past were fitted with very few antennas. In most cases only an AM or FM antenna was required. In contrast to this, today's vehicles are fitted with a plethora of antennas to receive a wide variety of signals at a number of different frequencies. This work presents a wideband radiating structure capable of sending and receiving many of the signals required in a modern vehicle from a single device. The antenna is based on Planar Inverted Cone Antenna geometry. The effect of bending or curving the antenna substrate is investigated at values in the range that may be required for vehicular integration.

This paper summarises the effects of turbulence on the aerodynamics of road vehicles, including effects on forces and aero-acoustics. Data are presented showing that a different design of some vehicles may result when turbulent flow is employed. Methods for generating turbulence, focusing on physical testing in full-size wind tunnels, are discussed. The paper is Part Two of a review of turbulence and road vehicles. Part One (Cooper and Watkins, 2007) summarised the sources and nature of the turbulence experienced by surface vehicles.

Vortices formed around the A-pillar region dictates the pressure distribution on the side panels of a passenger vehicle and also can lead to aerodynamic noise generation. This paper compares the suitability of various turbulence models in simulating the flow behind a vehicle A-pillar region under laboratory operating conditions. Commercial software's (FLUENT and SWIFT) were used to compare the performance of various turbulence models. In FLUENT, a simplified vehicle model with slanted A-pillar geometry was generated using GAMBIT and in SWIFT, the simplified vehicle model was generated using Fame Hybrid. Computational Fluid Dynamics (CFD) simulations were carried out using FLUENT under steady state conditions using various turbulence models (k-, k- Realize, k- RNG, k- and Spalart Allamaras). In SWIFT, k-, A-RSM and HTM2 turbulence models were used for the steady state simulations. Investigations were carried out at velocities of 60, 100 and 140km/h and at 0-degree yaw angle.

The focus of internal combustion (IC) engine research is the improvement of fuel economy and the reduction of the tailpipe emissions of CO2 and other regulated pollutants. Promising solutions to this challenge include the use of both direct-injection (DI) and alternative fuels such as liquefied petroleum gas (LPG). This study uses Mie-scattering and schlieren imaging to resolve the liquid and vapor phases of propane and iso-octane, which serve as surrogates for LPG and gasoline respectively. These fuels are imaged in a constant volume chamber at conditions that are relevant to both naturally aspirated and boosted, gasoline direct injection (GDI) engines. It is observed that propane and iso-octane have different spray behaviors across these conditions. Iso-octane is subject to conventional spray breakup and evaporation in nearly all cases, while propane is heavily flash-boiling throughout the GDI operating map.

The innovative highly flexible wings made of extremely light structures, yet still capable of carrying a considerable amount of non- structural weights, requires significant effort in structural simulations. The complexity involved in such design demands for simplified mathematical tools based on appropriate nonlinear structural schemes combined with reduced order models capable of predicting accurately their aero-structural behaviour. The model presented in this paper is based on a consistent nonlinear beam-wise scheme, capable of simulating the unconventional aeroelastic behaviour of flexible composite wings. The partial differential equations describing the wing dynamics are expanded up to the third order and can be used to explore the effect of static deflection imposed by external trim, the effect of gust loads and the one of nonlinear aerodynamic stall.

The aim of this paper is to develop a new concept of unconventional airship based on morphing a lenticular shape while preserving the volumetric dimension. Lenticular shape is known to have relatively poor aerodynamic characteristics. It is also well known to have poor static and dynamic stability after the certain critical speed. The new shape presented in this paper is obtained by extending one and reducing the other direction of the original lenticular shape. The volume is kept constant through the morphing process. To improve the airship performance, four steps of morphing, starting from the lenticular shape, were obtained and compared in terms of aerodynamic characteristics, including drag, lift and pitching moment, and stability characteristics for two different operational scenarios. The comparison of the stability was carried out based on necessary deflection angle of the part of tail surface.

Accurate and robust tracking of objects is of growing interest amongst the computer vision scientific community. The ability of a multi-sensor system to detect and track objects, and accurately predict their future trajectory is critical in the context of mission- and safety-critical applications. Remotely Piloted Aircraft System (RPAS) are currently not equipped to routinely access all classes of airspace since certified Detect-and-Avoid (DAA) systems are yet to be developed. Such capabilities can be achieved by incorporating both cooperative and non-cooperative DAA functions, as well as providing enhanced communications, navigation and surveillance (CNS) services. DAA is highly dependent on the performance of CNS systems for Detection, Tacking and avoiding (DTA) tasks and maneuvers.

When presented with new technology that removes past constraints, it is often beneficial to revisit old learning's to see if they still hold, and to understand how these can be best applied to the new technology. Brake-By-Wire (BBW) systems replace all the mechanical linkages of conventional hydraulic brake systems with ‘dry’ electrical components [2],[3]. The advent of this technology poses the possibility of revisiting conventional ABS control systems by utilizing the continuous nature that BBW offers. Presented is a BBW model based wheel slip controller using a generic continuous time Model Predictive Control (MPC) algorithm [15]. The result being the first of many steps taken in understanding the full potential that BBW systems offer.

Multi-Sensor Data Fusion (MSDF) techniques involving satellite and inertial-based sensors are widely adopted to improve the navigation solution of a number of mission- and safety-critical tasks. Such integrated Navigation and Guidance Systems (NGS) currently do not meet the required level of performance in all flight phases of small Remotely Piloted Aircraft Systems (RPAS). In this paper an innovative Square Root-Unscented Kalman Filter (SR-UKF) based NGS is presented and compared with a conventional UKF governed design. The presented system architectures adopt state-of-the-art information fusion approach based on a number of low-cost sensors including; Global Navigation Satellite Systems (GNSS), Micro-Electro-Mechanical System (MEMS) based Inertial Measurement Unit (IMU) and Vision Based Navigation (VBN) sensors.

A kinetic energy recover system (KERS) captures the kinetic energy that results when brakes are applied to a moving vehicle. The recovered energy can be stored in a flywheel or battery and used later, to help boost acceleration. KERS helps transfer what was formerly wasted energy into useful energy. In 2009, the Federation Internationale de l’Automobile (FIA) began allowing KERS to be used in Formula One (F1) competition. Still considered experimental, this technology is undergoing development in the racing world but has yet to become mainstream for production vehicles. The Introduction of this book details the theory behind the KERS concept. It describes how kinetic energy can be recovered, and the mechanical and electric systems for storing it. Flybrid systems are highlighted since they are the most popular KERS developed thus far. The KERS of two racing vehicles are profiled: the Dyson Lola LMP1 and Audi R18 e-tron Quattro.

Global Navigation Satellite Systems (GNSS) can support the development of low-cost and high performance navigation and guidance architectures for Unmanned Aircraft Systems (UAS) and, in conjunction with suitable data link technologies, the provision of Automated Dependent Surveillance (ADS) functionalities for cooperative Sense-and-Avoid (SAA). In non-cooperative SAA, the adoption of GNSS can also provide the key positioning and, in some cases, attitude data (using multiple antennas) required for automated collision avoidance. A key limitation of GNSS for both cooperative (ADS) and non-cooperative applications is represented by the achievable levels of integrity. Therefore, an Avionics Based Integrity Augmentation (ABIA) solution is proposed to support the development of an Integrity-Augmented SAA (IAS) architecture suitable for both cooperative and non-cooperative scenarios.

The maturity reached in the development of Unmanned Air Vehicles (UAVs) systems is making them more and more attractive for a vast number of civil missions. Clearly, the introduction of UAVs in the civil airspace requiring practical and effective regulation is one of the most critical issues being currently discussed. As several civil air authorities report in their regulations “Sense and Avoid” or “Detect and Avoid” capabilities are critical to the successful integration of UAV into the civil airspace. One possible approach to achieve this capability, specifically for operations beyond the Line-of-Sight, would be to equip air vehicles with a vision-based system using cameras to monitor the surrounding air space and to classify other air vehicles flying in close proximity. This paper presents an image-based application for the supervised classification of air vehicles.

Flow control over aerodynamic shapes in order to achieve performance enhancements has been a lively research area for last two decades. Synthetic Jet Actuators (SJAs) are devices able to interact actively with the flow around their hosting structure by providing ejection and suction of fluid from the enclosed cavity containing a piezo-electric oscillating membrane through dedicated orifices. The research presented in this paper concerns the implementation of zero-net-mass-flux SJAs airflow control system on a NACA0015, low aspect ratio wing section prototype. Two arrays with each 10 custom-made SJAs, installed at 10% and 65% of the chord length, make up the actuation system. The sensing system consists of eleven acoustic pressure transducers distributed in the wing upper surface and on the flap, an accelerometer placed in proximity of the wing c.g. and a six-axis force balance for integral load measurement.

A morphing ram-air intake, capable of deploying from a flat, closed surface to an open state is investigated. Via geometric and material optimisation, an origami-inspired folding structure is developed to exhibit bi-stable behaviour. An iterative finite element design process was conducted, noting the effects of the critical design properties of geometry, bending stiffness and material strain limits on bi-stability and the achievable geometric shape change. As a first step, thermoplastic polyurethane elastomer materials are proposed while increased stiffness by fibre reinforcements are considered at a later design stage and evaluated under aerodynamic loading. The bi-stable structure is capable of remaining in either open or closed stable configurations without sustained actuation. The ability to retract the intake when not required has the potential to reduce drag. It is envisioned that such a concept may be readily adopted within automotive and aerospace applications.

The design of a longitudinal stability augmentation system (SAS) for an aircraft with reduced tail size in the preliminary design phase is presented. Reducing tail size will reduce drag and weight and result in better fuel consumption, but it will reduce the level of stability. A control law is designed to give the aircraft the same stability level as that with the initial tail size. The feedback gains of the control law is computed with the equivalent stability derivative criteria of and CmαCmq . The paper also gives an overview of classical root locus and pole placement method and demonstrates that equivalent stability derivative criteria is suitable for preliminary aircraft design applications. Moreover, the control laws are also synthesized using robust control LQG/LTR which can be elaborated more in the detail design phase.

Avionic system developers are currently working on innovative technologies that are required in view of the rapid expansion of global air transport and growing concerns for environmental sustainability of aviation sector. Novel Communication, Navigation and Surveillance (CNS) system designs are being developed in the CNS/Air Traffic Management (CNS/ATM) and Avionics (CNS+A) context for mission-and safety-critical applications. The introduction of dedicated software modules in Next Generation Flight Management Systems (NG-FMS), which are the primary providers of automated navigation and guidance services in manned aircraft and Remotely-Piloted Aircraft Systems (RPAS), has the potential to enable the significant advances brought in by time and trajectory based operations. High-integrity, high-reliability and all-weather services are required in the context of four dimensional Trajectory Based Operations / Intent Based Operations (TBO/IBO).

This paper introduces the Seabus SB-8, a new Wing-In-Ground-Effect (WIGE) craft designed for 8 - 10 passengers. The craft will be used for fast transportation across Port Phillip Bay in Melbourne, Australia. With a cruise speed of about 140 km/hr, it can cross the bay in 30 min as compared to 75 min for land transportation. Computational Fluid Dynamics (CFD) analysis was conducted on the design to determine aerodynamic properties at various angles of attack and operating heights. The influence of ground effect was also determined as well as the effect of Centre of Gravity (CG) position on longitudinal stability. Using flow visualization areas of potential flow separation were identified and interactions of wake vortices with different parts of the aircraft were determined. Note that some aspects of the design are proprietary.

This paper presents the conceptual design of a new low-cost measurement system for the determination of pollutant concentrations associated with aircraft operations. The proposed system employs Light Detection and Ranging (LIDAR) and passive electro-optics equipment installed in two non-collocated components. The source component consists of a tuneable small-size and low-cost/weight LIDAR emitter, which can be installed either on airborne or ground-based autonomous vehicles, or in fixed surface installations. The sensor component includes a target surface calibrated for reflectance and passive electro-optics equipment calibrated for radiance, both installed on an adjustable support. The proposed bistatic system determines the column-averaged molecular and aerosol pollutant concentrations along the LIDAR beam by measuring the cumulative absorption and scattering phenomena along the optical slant range.