Search Results

A five-vehicle, 64 000-km test with 7.45 litre V-8 engines was conducted to determine if synthetic engine oils provided performance sufficiently superior to that of conventional engine oils to permit longer oil change intervals. The results show better performance in two areas of deposit control; inferior performance with respect to wear protection; and essentially equivalent performance in the areas of fuel and oil economies. Based on these data, it was concluded that synthetic engine oils do not provide the necessary performance required to safely recommend their use for extended oil change intervals. In addition, a cost analysis shows that the use of synthetic engine oils, even at a change interval of 32 000 km, will essentially double the customers' cost compared with conventional engine oils at GM's current 12 000-km change interval.

An analytical study of right angle barrier crashes has been conducted to evaluate the influence of vehicle crush distance, occupant spacing, and interior crush stiffness on the severity of occupant-interior impact. Particular attention was directed to the influence of the vehicle deceleration-time history wave shape. The study includes an analysis of a simple-point occupant and a more complicated articulated dummy. The results of these analyses are in substantial agreement and indicate that the most important factors in reducing unrestrained occupant impact severity in conventional vehicles are occupant spacing, vehicle crush distance, and interior crush stiffness. Because of practical considerations and the multiplicity of crash conditions, it is concluded that the most direct way to reduce injury and death is through improved vehicle interior crush behavior.

The use of multigrade (V.I. improved) oils in automotive engines has increased significantly in recent years. However, the performance of these oils in terms of factors such as oil economy, wear, and noise, is not always equal to that of single grade oils. Although the initial viscosity of multigrade oils is related to both the base oil and the V.I. improver, the viscosity decreases with use, with the primary factors determining the magnitude of the change being the degree of shear and the characteristics and concentration of the V.I. improver used. This decrease in viscosity has been assumed to be the cause of the decreases in oil economy that may occur with oil use. However, viscosity changes are not believed to be the primary factor responsible since similar oil economy changes have also been observed for single grade oils. Nevertheless, the characteristics and concentration of the V.I. improver used can be a significant factor influencing oil economy.

This paper describes the usage of an exponential weighting factor for appraising deceleration or force impulses registered on dummies or impacting hammers in safety testing. The proposed impulse-integration procedure, it is shown, takes into account in a more rational way, and in better conformity with published injury tolerance data, the relative importance of time and intensity of the pulse than do the “peak g” or impulse-area criteria. Use of the new Severity Index for assessment of head impact pulses is illustrated. It is shown to be of special value in comparing the relative severity of pulses which differ markedly in shape (because of structural differences in the component being struck) and it is pointed out that without a weighting factor of this nature, laboratory impact tests can yield incorrect ranking of the relative safety merit of alternative designs. Automated methods for quick calculation of the Severity Index are possible.

Utilizing unembalmed cadaver test subjects, a series of tests was carried out to characterize quantitatively the resistance of the skin, the soft underlying tissue of the scalp, and certain other typical areas of the body to impact loading. The impacts were delivered by the use of an instrumented free-fall device similar to that previously employed for facial bone fracture experiments. In one group of tests, metal and glass edges were affixed to the impacting device to produce localized trauma under conditions which were standardized with respect to variables affecting the degree of the injury. In the second group of experiments, specimens of skin, together with underlying tissue of uniform thickness, were subjected to compressive impact between the parallel surfaces of the impacting weight and a heavy metal platen. From these latter experiments the force-time histories, coefficient of restitution, and hysteresis loops of load versus deflection were obtained for the specimens.

A professional high diver, instrumented with accelerometers, performed sixteen dives from heights between 27-57 ft. For each dive, he executed a 3/4 turn and landed supine on a 3-ft deep mattress which consisted of pieces of low-density urethane foam encased in a nylon cover. Using FM telemetry, sagittal plane decelerations were recorded for a point either on the sternum or the forehead. Impact velocities and corresponding stopping distances for the thorax and the head were calculated from high-speed movies of the dives. For a 57-ft dive, the impact velocity of the thorax was 41 mph with a corresponding stopping distance of 34.6 in. The peak resultant deceleration of the thorax was 49.2 g with a pulse duration of 100 ms. The maximum rate of change of the deceleration of the thorax was 5900 g/s. No discomfort was experienced as a result of this impact. The maximum forehead deceleration occurred during a 47.0-ft drop and exceeded 56 g with a Gadd Severity Index greater than 465.

Two Highway Safety Research Institute (HSRI) dummies were tested and evaluated. Based on the analysis given, the HSI dummy should not be used for vehicle qualification testing. However, many of its components offer viable alternatives for future dummy development. The dummy was found to have inadequate biomechanical fidelity in the head, neck, and chest, although its characteristics were very promising and, as a whole, biomechanically superior to the Hybrid II. Its repeatability and reproducibility in dynamic component tests were better than the Hybrid II dummy. In particular, the HSRI friction joints were outstanding in repeatability and had a significant advantage in usability in that they do not require resetting between tests. In three-point harness and ACRS systems tests, the values of injury criteria produced by the HSRI dummy were generally lower than those obtained with the Hybrid II, especially the femur loads in the ACRS tests.

To compute the tearing energy of nicked rubber strips in extension, one has to solve first the associated stress-deformation involving finite elasticity. In the past, this was a formidable task so that the tearing energy had been determined solely by experiments and only for a few testpieces. With the aid of the finite element method (FEM), it is shown that this may now be done simply through the use of the Rice's J integral. Tearing energy for two testpieces are computed and results compared with existing experimental data. The agreement is good. Because of FEM's ability to treat general geometric and loading conditions, the use of the J integral in combination with FEM to cmpute the tearing energy now allows a wider application of the tearing energy concept to more complex units than hitherto known.

The intent of this paper is to put into proper perspective the relationships among the vehicle, the thermodynamic cycle, and the combustion process as they relate to exhaust emissions from a gas turbine-powered passenger car. The influence of such factors as car size, installed power, regeneration, and other cycle variables on level road load fuel economy, and on the production of oxides of nitrogen and carbon monoxide, are examined. In limited checks against experimental data, the mathematical model of the combustor used in this study has proved to be a reliable indicator of emission trends. The calculated emission levels are not final, however, with deficiencies subject to improvement as new combustor concepts are developed.

Various proposals for emissions cleanup systems have shown the desirability of regulating engine air-fuel ratio within precise limits. For this purpose a prototype exhaust sensor has been investigated. The sensor is a ceramic device, made of stabilized zirconia, which operates via electrochemical principles. It is placed directly in the exhaust stream and generates a voltage signal which is an approximate indication of engine air-fuel ratio. Several sensors have been installed in situ on engines operated under controlled dynamometer conditions. Fundamental response characteristics of the sensors have been determined. The results of this investigation, together with descriptions of the construction and installation configuration of the prototype sensor, are discussed.

ANALYSES of crankcase vent gases by several methods have shown that crankcase and exhaust hydrocarbon emissions from automobiles are of the same order of magnitude. Internal ventilation of the crankcase to the engine intake system eliminates crankcase emission, thus providing a practical control of this important source of air pollution.*

A radiometric method has been developed for the determination of camshaft wear during engine operation. After a radioactive tracer is induced at the tips of one or more cam lobes by the technique of surface layer activation, calibration procedure are performed to determine the amount of radioactive material remaining versus the depth worn. The decrease in γ-ray intensity measured external to the engine is then directly related to cam lobe wear. By incorporating a high-resolution detector and an internal radioactive standard,measurement accuracy better than ±0.2 μm at 95% confidence has been achieved. Without the requirement of engine disassembly, this method has provided unique measurements of break-in wear and wear as a function of operating conditions. Because this approach requires only low levels of radiation, it has significant potential applications in wear control.

Future low emissions engines will burn unleaded gasoline. Compared with engines of 1970, future engines will have lower concentrations of NOx in the blowby gases, and lower blowby flow-rates; however, oil temperatures will probably be unchanged. The consequences of these conditions for engines using high quality (SE) oils at current drain intervals are: virtual elimination of rust, reduction of sludge, no effect on wear and oil thickening, and possible worsening of varnish. Therefore, extension of the drain interval with SE engine oils in the future may be possible, but final decisions will depend on the findings of research in the areas of engine wear and varnish, and oil thickening.

A novel method for the intermittent supercharging of an internal combustion engine in a vehicle is described. During full throttle operation, high pressure motivating air entrains ambient air and compresses it to an intermediate pressure in the diffuser of an air ejector. Flowing through the carburetor and into the engine, the supplemental air augments engine power, reducing vehicle acceleration time by as much as one-third. By allowing engine size to be reduced, better economy without loss of performance is possible. Typical vehicle installations are described and problem areas discussed.

This study explores the application of viscoelastic modeling for characterization of the response of the brain to impulsive loading with the objective of learning whether such models could exhibit the same time dependency of strain or likelihood of injury, as exhibited by the Severity Index, HIC Index, Wayne Tolerance Curve, and other similar representations of tolerance. The mathematical relationships between viscoelastic properties and the corresponding time dependency of tolerance are shown for Newtonian, Bingham plastic, and Pseudo-Bingham, as well as more general behavior. Preliminary static and dynamic tests upon small mammalian material are described with particular attention given to strain in the vicinity of the brainstem as a function of loading profile. Both the theoretical and experimental results show that the falling time dependency of the above indexes can be interpreted in terms of nonlinear viscoelastic response.

This paper summarizes an analysis, design, and test project in which a dummy chest structure was developed. The chest consisted of mechanical elements that had been characterized by computer simulations as giving responses to blunt frontal impacts necessary for biofidelity. An analysis of mechanical rib structures indicated that materials having a high ratio of yield stress to modulus of elasticity were required. Only metals having unusually high yield strengths, such as spring steels, qualified. A mechanical system was developed with steel ribs pivoted at each end as a primary spring. A secondary spring was a pair of commercially available die springs acting in parallel with the ribs after 25.4 mm (1.00 in) deflection. A fluid damper was developed to provide the damping. The chest structure was tested under conditions modified from those used by Kroell. The modifications were holding the spine rigidly and reducing the impact masses.

A viscoelastic neck structure that responds to impact environments in a manner similar to the human neck is described. The neck structure consists of four ball-jointed segments and one pin-connected “nodding” segment with viscoelastic resistive elements inserted between segments that provide bending resistance as well as the required energy dissipation. Primary emphasis was placed on developing appropriate flexion and extension responses with secondary emphasis placed on axial, lateral, and rotational characteristics. The methods used to design the resistance elements for the neck structure are discussed. Three variations of the resistive elements have been developed that meet the response characteristics based on the data of Mertz and Patrick. However, no single resistive element has satisfied the flexion and extension characteristics simultaneously, but such an element appears to be feasible.

To lower emissions from a multicylinder engine, the air-fuel ratio must be optimized in all cylinders. If uniform fuel distribution is achieved, then the cylinder-to-cylinder air distribution is of particular interest. A probe system has been developed to measure mass flow rates to individual cylinders during operation of a complete engine. Fast response measurements of pressure, temperature, and flow velocity are made in the intake port near the valve during the intake portion of the cycle. High-speed collection of the large volume of data was accomplished through on-line use of an IBM 1800 computer. A V8 455 CID (7457 cm3) engine with stock intake and single exhaust system was used in the initial application of the mass flow probe. Measurements of 30-40 individual cycles were combined to calculate the mean volumetric efficiency for each cylinder.

Noise produced by automotive ignition systems can deteriorate the performance of nearby communication systems. An important step toward alleviating this difficulty is to characterize the ignition noise. Measurements have been made of the noise peak amplitude distribution of a number of identically equipped vehicles over a fixed period of time. Both vertical and horizontal polarizations were used, and measurements were made at two frequencies, 145 and 230 MHz. These statistics were then compared to various probability distributions to attempt to characterize the amplitude distribution of the noise. The distributions studied were: the log-normal, the exponential, the Rayleigh, and the Weibull distributions. It was concluded that the best fit was provided by the Weibull distribution. The parameters of the best fitting distribution are primarily a function of the antenna's polarization, with frequency having only a minor effect.

The use of relatively small catalytic converters containing alumina-supported platinum (Pt) and palladium (Pd) catalysts to control exhaust emissions of hydrocarbons (HC) and carbon monoxide (CO) was investigated in full-scale vehicle tests. Catalytic converters containing 70-80in3 of fresh catalyst were installed at two converter locations on the vehicle. Carburetion was richer than stoichiometric, with air-fuel ratios (A/F) comparable to those proposed for dual-catalyst systems containing an NOx reduction catalyst. The vehicle was equipped with exhaust manifold air injection. Homogeneous thermal reaction in the exhaust manifolds played a significant role in the overall control of HC and CO. Four Pt catalysts, three Pd catalysts, and one Pt-Pd catalyst were prepared and evaluated. Total metal loadings were varied 0.01-0.07 troy oz. Hydrocarbon conversion efficiencies varied 62-82%, measured over the 1975 cold-hot start weighted Federal Test Procedure.