Search Results

Laser excitation wavelengths for two-line planar laser-induced fluorescence (PLIF) of 3-pentanone have been optimized for simultaneous imaging of temperature and composition under engine-relevant conditions. Validation of the diagnostic was performed in a motored optical IC engine seeded homogeneously with 3-pentanone. PLIF measurements of the uniform mixture during the compression stroke were used to measure the average temperature and to access the random uncertainty in the measurements. To determine the accuracy of the temperature measurements, experimental average temperatures were compared to values computed assuming isentropic compression and to the output of a tuned 1-D engine simulation. The comparison indicated that the absolute accuracy of the temperature measurements is better than ±5%. Probability density functions (PDFs) calculated from the single-shot images were used to estimate the precision of the measurements.

Standard CFD methods require a mesh that fits the boundaries of the computational domain. For a complex geometry the generation of such a grid is time-consuming and often requires modifications to the model geometry. This paper evaluates the Immersed Boundary (IB) approach which does not require a boundary-conforming mesh and thus would speed up the process of the grid generation. In the IB approach the CAD surfaces (in Stereo Lithography -STL- format) are used directly and this eliminates the surface meshing phase and also mitigates the process of the CAD cleanup. A volume mesh, consisting of regular, locally refined, hexahedrals is generated in the computational domain, including inside the body. The cells are then classified as fluid, solid and interface cells using a simple ray-tracing scheme. Interface cells, correspond to regions that are partially fluid and are intersected by the boundary surfaces.

This paper presents a new measurement technique for in-cylinder gas temperature and residual gas concentration during the compression stroke of an internal combustion (IC) engine. This technique is based on the infrared absorption of water vapor by a wavelength modulated laser. Wavelength modulation spectroscopy with second harmonic detection (WMS-2f) was adopted to enable the short-path measurements over a wide range of temperatures and pressures corresponding to the late compression stroke in a typical automotive engine. The WMS-2f signal is detected through a bandpass filter at a width of 7.5 kHz, enabling crank angle-resolved measurements. The temperature is determined from the ratio of optical absorption for two overtone transitions of water vapor in the intake gas mixture, and the H2O concentration is determined from this inferred temperature and the absorption for one of the transitions.

For high-load applications, natural gas represents a clean burning, readily available, and relatively inexpensive alternative to number 2 Diesel fuel. However, the fuel’s poor ignitability has previously limited implementation to spark ignited and dual-fueled engines. These approaches suffer from reduced peak load and high engine-out particulate emissions, respectively, requiring lean operation and expensive aftertreatment to meet regulatory standards. A high-temperature combustion strategy can overcome the difficult ignitibility, allowing for true Diesel-style combustion of pure methane-the least ignitable and least sooting component of natural gas. In order to achieve this result, a compression system was designed to supply fuel at pressures suitably high to achieve good mixing and short injection durations, and a solenoid-actuated Diesel fuel injector was modified to function at these pressures with a gaseous fuel.

This paper describes the computational results of the flow field around two vehicle geometries using the Immersed Boundary (IB) technique in conjunction with a steady RANS CFD solver. The IB approach allows the computation of the flow around objects without requiring the grid lines to be aligned with the body surfaces. In the IB approach instead of specifying body boundary conditions, a body force is introduced in the governing equations to model the effect of the presence of an object on the flow. This approach reduces the time necessary for meshing and allows utilization of more efficient and fast CFD solvers. The simulations are carried out for an SUV and a pickup truck models at a Reynolds number of 8×105. Cartesian meshes (non-uniform) with local grid refinement are used to increase the resolution close to the boundaries. The simulation results are compared with the existing measurements in terms of surface pressures, velocity profiles, and drag coefficients.

Predicting the aerodynamic performance of an aircraft in icing conditions is critical as failures in an aircraft’s ice protection system can compromise flight safety. Aerodynamic effects of icing have typically relied on RANS modeling, which usually struggles to predict stall behavior, including those induced by surface roughness. Encouraged by recent studies using LES that demonstrate the ability to predict stall characteristics on full aircraft with smooth wings at an affordable cost [1], this study seeks to apply this methodology to icing conditions. Measurements of lift, drag, and pitching moments of a NACA23012 airfoil under clean and iced conditions are collected at Re = 1.8M. Using laser scanned, detailed representations of the icing geometries, LES calculations are conducted to compare integrated loads against experimental measurements in both clean and iced conditions at various angles of attack through the onset of stall [2].

Negative valve overlap (NVO) is a valve strategy employed to retain and recompress residual burned gases to assist HCCI combustion, particularly in the difficult regime of low-load operation. NVO allows the retention of large quantities of hot residual burned gases as well as the possibility of fuel addition for combustion control purposes. Reaction of fuel injected during NVO increases charge temperature, but in addition could produce reformed fuel species that may affect main combustion phasing. The strategy holds potential for controlling and extending low-load HCCI combustion. The goal of this work is to demonstrate the feasibility of applying two-wavelength PLIF of 3-pentanone to obtain simultaneous, in-cylinder temperature and composition images during different parts of the HCCI/NVO cycle. Measurements are recorded during the intake and main compression strokes, as well as during the more challenging periods of NVO recompression and re-expansion.

Combustion under stratified operating conditions in a direct-injection spark-ignition engine was investigated using simultaneous planar laser-induced fluorescence imaging of the fuel distribution (via 3-pentanone doped into the fuel) and the combustion products (via OH, which occurs naturally). The simultaneous images allow direct determination of the flame front location under highly stratified conditions where the flame, or product, location is not uniquely identified by the absence of fuel. The 3-pentanone images were quantified, and an edge detection algorithm was developed and applied to the OH data to identify the flame front position. The result was the compilation of local flame-front equivalence ratio probability density functions (PDFs) for engine operating conditions at 600 and 1200 rpm and engine loads varying from equivalence ratios of 0.89 to 0.32 with an unthrottled intake. Homogeneous conditions were used to verify the integrity of the method.

Cocktail shaker cooling is the commonly used term to describe heat transfer in a reciprocating hollow cylinder partially filled with a liquid. The sodium filled valve is a widely used application of this heat transfer concept. This paper presents information that may be useful in the design of cocktail shaker cooled pistons and valves. The design data are presented in nondimensional form using parameters typical of conventional convective heat transfer correlations. An illustrative problem for a piston is presented to show the application of the design data.

Simultaneous crank-angle-resolved measurements of gasoline vapor concentration, gas temperature, and liquid fuel droplet scattering were made with three-color infrared absorption in a direct-injection spark-ignition engine with premium gasoline. The infrared light was coupled into and out of the cylinder using fiber optics incorporated into a modified spark plug, allowing measurement at a location adjacent to the spark plug electrode. Two mid-infrared (mid-IR) laser wavelengths were simultaneously produced by difference-frequency-generation in periodically poled lithium niobate (PPLN) using one signal and two pump lasers operating in the near-infrared (near-IR). A portion of the near-IR signal laser residual provided a simultaneous third, non-resonant, wavelength for liquid droplet detection. This non-resonant signal was used to subtract the influence of droplet scattering from the resonant mid-IR signals to obtain vapor absorption signals in the presence of droplet extinction.

The Rotating Disk Analytical System (R-DAS) is an in-situ, bio-analytical technology, which utilizes a micro-fluidic disk with similar form factor as an audio compact disc to enhance and augment microgravity-based cellular and molecular biology research. The current micro-fluidic assay performs live cell/dead cell analysis using fluorescent microscopy. Image acquisition and analysis are performed for each of the selected microscope slide windows. All images are stored for later download and possible further post analysis. The flight version of the R-DAS will occupy a double mid-deck shuttle locker or one quarter of an ISS rack. The control system for the R-DAS consists of a set of interactive software components. These components interact with one another to control disk rotation, vertical and horizontal stage motion, sample incubation, image acquisition and analysis, and human interface.

This paper presents and validates a model of fatigue crack propagation in resistance spot welded joints; this model is called the “Structural Stress Model” (SSM). Important features of the SSM are that it is based on the physical evidence of fatigue in spot welded joints and on well-accepted descriptors of fatigue more generally. Furthermore, it is usable by designers evaluating fatigue response of structures containing multiple welds. Underlying assumptions of the SSM are also reviewed.