Search Results

In the recent years steering feel characteristics have emerged as one of the important brand image attributes of automotive OEMs. Since past few decades, the hydraulic assisted steering system (HPAS) on which lot of research was done to tune the steering feel has been taken over by electric power assisted steering (EPAS) system. The EPAS primarily uses an electric motor controlled by an electronic control unit to assist the driver in maneuvering the vehicle. The next big leap in the steering system advancement is steer-by-wire (SbW) technology where the mechanical linkage between the steering wheel and the road wheels is eliminated. The advantages of this system are ease to use, elimination of noise-vibration-harshness of steering system caused by road forces, modularly of steering system for packaging, improved visibility to front-end displays and road ahead and a fun to drive concept.

The fuel economy of heavy commercial vehicles can be significantly improved by reducing the rolling resistance of tires. To reduce the rolling resistance of 6×4 tractor, the super single tires instead of rear dual wheel tires are tried. Though the field trials showed a significant increase in fuel economy by using super single tires, it posed a concern of road safety when these tires blowout during operation. Physical testing of tire blowout on vehicle is very unsafe, time consuming and expensive. Hence, a full vehicle simulation of super single tire blowout is carried out. The mechanical properties of tires such as cornering stiffness, radial stiffness and rolling resistance changes during the tire blowout; this change is incorporated in simulation using series of events that apply different gains to these mechanical properties.

In today's scenario, most of the OEMs use manual transmissions with synchronizer gear shifting system for ease of gear shifting. It gives very high fuel efficiency. Gear shifting is a customer touch point, hence it is very important to select adequate synchronizer capacity so that it will perform in better and last longer. To test the synchronizers, there are many test methods which give the idea about life of synchronizer and its performance, in different conditions. Regular synchronizer rig tests consume lot of time in deriving the results. So it is very important to find out a way which will give same results within short time period. To carry out the short time test or accelerated test, we need to understand the effect of various factors like reflected inertia, drag torque, differential speed, synchronizing time, and gear shifting force on synchronizer capacity.

For sustainability in automobile manufacturing, recycle, reuse, and repair of used up cutting tools is now an established process. Although many types of tools were designed for one time use and then throw, an increasing awareness of the impact on the natural resources have made manufacturers to put some of these back to use or sell it back to suppliers who have put up a mechanism to extract the elements e.g. Tungsten and use it for manufacturing of new tools. There are many ways in which cutting tools can be recycled. Be it by reshaping a used up throwaway type tool [1], by redesigning of a tool holder for the use of unused cutting edges [2] or reusing short length drills that are used in making of long oil holes in crank case, cylinder head, cam shaft or connecting rods [3]. This paper demonstrates successful use of used up crankshaft grinding wheels.

Due to the recent trend in auto industry to opt for higher power engines, causes increase in vibrations levels in the passenger’s compartment. This requires a better and comprehensive model to analyze vibrations from engine to seat and steering wheel much before the proto stage of development in the design stage itself. For this purpose, modelling is done in ADAMS multi dynamics and assuming the 16 degrees of freedom of the vehicle. Further, a crank drive model is developed to simulate engine excitation forces comprising unbalanced inertia forces and torque fluctuations and their effects seat rail and steering wheel vibration is derived. This tool is an attempt to predict such vibrations caused and assist in design enhancement and streamline the procedure.

Twist beam is a semi-independent suspension having two trailing arms attached to the chassis via rubber bushes. Closed profile ‘V’ shaped cross beam interconnects left and right side arms. It provides roll stiffness of the suspension, by twisting as the two wheels moves relative to each other. Due to driving and road conditions twist beam structures are subjected to cyclic twist loads resulting into roll fatigue failure mode [1]. To design twist beam for mass, package and performance it is required to find realistic cross articulations based on vehicle application, usage pattern and protect twist beam from roll fatigue failure mode. The objective of this paper is to develop a virtual method using ‘ADAMS ®’ multibody dynamics software for maximum relative wheel center displacements during realistic hilly areas conditions. This paper describes half and full vehicle based virtual approach for twist beam cross articulations in hilly area conditions.

Apart from being an active safety system the brake system represents an important aspect of the vehicle dynamics. The vehicle retardation and stopping distance completely depend upon the performance of brake system and the functionality of all components. However, the performance prediction of the entire system is a challenging task especially for a complex configuration such as multi-axial vehicle applications. Furthermore, due to its complexity most often the performance prediction by some methods is limited to static condition. Hence, it is very important to have equivalent mathematical models to predict all performance parameters for a given configuration in all different conditions This paper presents the adopted system modelling approach to model all the elements of the pneumatic brake system such as dual brake valve, relay valve, quick release valve, front and rear brake actuators, foundation brake etc.

Twist-beam suspensions are an example of design solution presenting acceptable performance when applied to passenger cars & light vehicles and it can provide an optimal between cost & performance in the automotive market. For these reasons, twist beam is quite popular in use in rear suspension of light vehicles. In contrary to other types of suspension, the twist-beam has a flexible torsion beam connecting the swing arms. The study of the deformation of this flexible element becomes important to understand its performance and durability behavior. As the name signifies, twist beam major performance attribute is control of twist or opposite wheel travel arising from vehicle roll or road input. Current approach for the study this deformation is through FEA & Multi-body dynamics software tools.

With increased awareness about environmental issues, the trend of automobile industry is to use ‘Recycled’ or ‘Biodegradable’ or ‘Energy Recoverable’ material. As a part of this programme, to make the vehicle ‘Green’ in nature, many automobile OEMs have taken the initiative to make use of natural fibre composite in their vehicles. Natural fibre based composite has been successfully proven for less critical as well as for semi-structural applications in an automobile. These typical applications are insulations, headlining, carpets, door pad etc. There is a demanding task for automotive OEMs to meet 85% Recyclability and 95% Recoverability targets by year 2015. To meet the RRR (Reuse, Recycle & Recover) and the ELV (End of Life) regulatory requirements, increased use of natural fibre based composite/ biopolymers is unavoidable. Natural fibre can offer potential advantages such as weight saving and improve overall green rating of the vehicle.

Cabin noise is a significant product quality criteria which enables the customers for product differentiation. There are various sources of cabin noise such as wind, structures(panels), engine, suspension, tire and roads. During product development phase, extensive tests has been conducted to improve vehicle dynamics behavior on various climatic conditions. One such test is accelerating vehicle on low mu or icy surface. While performing acceleration manoeuvre (tractions) on a low mu tracks, Cabin noise with source identified from front underbody & low tractive torque build up is reported. This undesirable behavior may occur due to following reason (1) Excitation of coupled modes between suspension and powertrain which induces torque fluctuation. (2) Transmissibility of various subsystem can be the reason for above problem statement. (3) Poorly chosen tire compounds and design leads to fluctuation in torque.

For a modified electric vehicle on the same internal combustion engine (ICE) platform, the primary consideration is to have no change in long member and pendulum type conventional engine mounting system to save development cost and timeline. Electric vehicle (EV) powertrain is comparatively lighter w.r.t the ICE. As a result, the engine mount’s static preload setting point or powertrain centre of gravity under static powertrain load gets changed resulting in a change in stiffness for the same engine mount. As the static stiffness changes, the dynamic stiffness and modal frequency also change. The 6 degrees of freedom (DOF) modal frequency has almost no impact on powertrain modes as EV powertrain modes, mainly, the motor frequency, is much higher than engine mount Eigen modes. In this scenario, the gap management gets disturbed due to less static preload, and non-linearity gets affected.

Aerodynamics performance evaluation of passenger cars is important during early vehicle development phase as it influences fuel economy, vehicle stability and drivability. Usually during initial styling phase, scale model is prepared and tested in wind tunnel to check aerodynamic performance like drag coefficient and these are used to predict aerodynamic performance of full scale model as testing on full scale model is costly and time consuming. To ensure its correctness, it is important to understand difference in physics from scale model to full scale model. In predicting full vehicle aerodynamics performance from scale model assessment; importance of Reynolds number, effect of geometric scaling on flow i.e. flow separation and wake zone change needs to be understood and addressed. This paper discusses about effect of scaling on aerodynamic flow behavior and drag.

Automotive Industry is constantly upgrading the value offered on their products at optimized cost. Scratch and mar resistance of interiors and exterior parts, is an important attribute which is linked to perceived quality and value offered to customers. Polypropylene material is optimum material of choice for these parts due to its unique advantages. However, filled polypropylene material has poor scratch and mar resistance. Many techniques for scratch resistance improvement are available such as additions of slip agents, co additives, special fillers, siloxanes, etc. However, some of them may offer some disadvantages like stickiness or tackiness on the surfaces. The choice depends on its effectiveness & cost. This paper deals with design of experiments to evaluate effectiveness of 4 types of additives and their optimum % to give scratch resistance improvement without having detrimental impact on other critical properties.

Regular vehicle has the advantage of Engine resistance even when it is not fired, hence chances of vehicle roll back on gradients will be minimized. This is not the case for Electric vehicles, which uses an electric motor that does not have any resistance offered to wheels that prevent vehicle roll back on gradient. This leads to increased load on the conventional hydraulic brakes due to absence of engine inertia. Hence, there is a need for a low cost and reliable automatic braking system which can help in holding the vehicle and assists the driver during launch in case he need to stop at a gradient. An Electromagnetic brake (EM brake) system can be used as a solution for the above-mentioned requirement. EM brake can provide hill hold and hill assist effect in addition to automatic parking brake application when the vehicle is turned-off. This system will assist anyone who need to halt the vehicle at a gradient and then relaunch it without much struggle.

Subject paper focuses primarily on non uniform tire wear problem of front steered wheels in a pickup model. Cause and effect analysis complemented with field vehicle investigations helped to identify some of the critical design areas. Investigation revealed that steering geometry of the vehicle is undergoing huge variations in dynamic condition as compared to initial static setting. Factors contributing to this behavior are identified and subsequently worked upon followed by a detailed simulation study in order to reproduce the field failures on test vehicles. Similar evaluation with modified steering design package is conducted and results are compared for assessing the improvements achieved. In usual practice, it is considered enough if Steering Geometry parameters are set in static condition and ensured to lie within design specifications.

The crankshaft is the component which transmits dynamic loads from cylinder pressure and inertial loads in engine operating conditions. Because of its crucial importance in functioning of engine and requisite to sustain high dynamic and torsional loading, crankshaft fatigue life is desired to be higher than the predicted engine operating life. Performance of the crank train in diesel engine applications largely depends on the components of its mass elastic system. Flywheel is one such component whose design affects the life of crankshaft. In the present study, the crank train comprising of torsional vibration damper, crankshaft and flywheel along with clutch cover is considered for analysis. Crankshaft dynamic simulation is performed with multi body dynamics technique, fatigue safety factors of crankshaft are calculated with dynamic loads under engine operating conditions.

Severe air pollution in cities caused largely by vehicular emissions, which requires urgent remedial measures. As automobiles are indispensable modes of personal and public mobility, pre-emptive efforts are necessary to reduce the adverse effects arising from their operation. A significant improvement in air quality can be achieved through large-scale introduction of vehicles with extremely low emission such as hybrid-electric and zero emission vehicles. Range extension of electric vehicles (EVs) is also of utmost importance to alleviate the handicap of restricted mileage of purely plug-in EVs as compared to conventional vehicles. This paper presents development of a polymer electrolyte membrane (PEM) fuel cell stack used for the range extender electric vehicles. The Fuel cell stack for range extender vehicle operated in a dead end mode using hydrogen and air as open cathode.

The recent vehicle development demands for electric powertrain as against conventional fuels engines. The electric powertrain offers advantages in terms of cleaner and quieter operations. In electric vehicle, the conventional engine is replaced by electric motor operated on batteries. Here, the conventional engine refers to those powered by diesel, petrol, CNG and some hybrid vehicles using fuel as primary source for power generation. Thus, the system design approach for mount also changes. At present, various approaches are being followed to mount electric powertrain like conventional pendulum type, with or without cradle, Common or different motor and electric box mountings etc. The electric powertrain differs from conventional powertrain in terms of weights, mass moment of inertia, torque, NVH requirements like Key in Key off, idling, low frequency vibrations etc. Thus conventional mount will not necessarily meet NVH requirements for Electric powertrains.

Vehicle aerodynamic design has a critical impact on fuel efficiency of the vehicle. Reducing aerodynamic wind resistance of the vehicle's exterior shape and reducing losses associated with requirements for engine compartment cooling through vehicle front openings plays key role in achieving desired aerodynamic efficiency. Today fairly large number of computational fluid dynamics (CFD) simulations are being performed during the vehicle aerodynamic design and development process and it is rapidly increasing day by day. Vehicle aerodynamic design and development process involves mainly aerodynamic shape development, aerodynamic optimizations of vehicle external components (side view mirror, spoilers, underbody shield etc.) and number of” what if studies during preliminary design process. Licensing costs of the available commercial CFD simulation solver has significant impact on product development cost when numbers of aerodynamic simulations expand.

The interior components of a passenger vehicle are designed to provide comfort and safety to its occupants. In the event of accident, vehicle interiors are primary source of injuries when occupants interact with them. Vehicle interiors consists of Instrument panel (IP), center console, seats and controls in front of seating position etc. Severity of the injuries depends on the energy dissipating characteristics, profiles, projections of different interior components. These are assessed by ECE R21 and IS12553 head form impact tests. To evaluate the Head form impact performance on Interior components, Computer Aided Engineering (CAE) simulations are extensively used during the vehicle development. In order to predict failure of plastic components and snap joints which might lead to expose sharp edges, it is critical to model plastic material and snap joint.