Search Results

Interactions between a Zinc dialkyldithiophosphate (ZDP) and three different commercially available succinimide dispersants were observed through changes in solutions behavior, as determined by viscometry and Fourier Transform Infrared spectroscopy (FTIR), and four-ball tests. The viscometric response observed for two component blends of ZDP and succinimide dispersant in white oil changed as a function of the molar Zn to N ratio, indicative of specific interactions. The break in the viscometric response curve occurred at Zn:N=0.13 for all three succinimide dispersants. FTIR spectra of the same ZDP-dispersant blends were examined and similar Zn:N dependencies were observed. Four-ball tests measuring wear scar diameter, seizure load and weld load showed a dependence on the Zn to N ratio similar to that observed by viscometry. At very low Zn to N ratios wear and seizure load were decreased, while at higher ratios the seizure and weld loads were increased over that for ZDP alone.

The functions of engine oil are reviewed. The chemistry of engine oil additives and synthetics is described in terms for the non-chemist. The latest SAE engine oil viscosity classifications and API service designations are detailed. Developments underway to upgrade engine oil quality are discussed.

Despite the many years of widespread use of the BMW Intake Valve Deposit (IVD) vehicle test, relatively little has been published quantifying the variation in the test procedure. This paper presents an analysis of the variability in the BMW test. Though results from 8045 km (8K; 5,000 mile) tests rather than 16090 km (16K; 10,000 mile) are highlighted due to the size of the available database and relative sensitivity of the data, analysis suggests that variation at 8K is representative of 16K variation. A square root transformation of average deposit weight at 8K, though more cumbersome than the more common log transformation, is found to be the most appropriate way to eliminate the dependence of variation on the absolute level of deposits. Within-car variation is found to account for over half of the test-to-test variation, contradicting the notion that car-to-car differences are the dominant source of variability.

Our basic understanding of the chemical and physical nature of soot, its interaction with lubricant components and its role in promoting wear and oil thickening in heavy duty diesel engines continues to grow. Our current study in the GM 6.5L engine focuses on examining the effects of variations in base stock type (Group I vs. Group II), viscosity index improver or viscosity modifier (VM) chemistry (OCP vs. dispersant OCP), zinc dithiophosphate (ZDP) type and dispersant type (low MW vs. high MW) on roller follower wear, viscosity growth and other measured responses. In this study, more robust fluids were tested producing very low wear results and minimal viscosity increase of the lubricant. Fluids containing dispersant OCP (DOCP) and high MW dispersant produced a lower degree of wear, whereas varying the ZDP type (1° vs. 2°) showed no effect on wear. The use of Group II base stocks was associated with significantly lower viscosity increases.

Statistically designed experiments were developed to investigate the nature of soot, to understand its role in oil viscosity growth, and to study the interactions involved with additives that inhibit viscosity growth. The matrix was designed to examine effects of engine type, mode of operation, and the oil formulations. Mack EM6-285 and GM 6.2L engines operating under both high speed and high torque conditions were used in this study. An API CE\SG quality lubricant was used as the baseline. The detergent sulfonate substrate was varied from standard to three-fold levels; the dispersant TBN contribution ranged from 1.1 to over 3.0. The surface and bulk exhaust soot properties were determined. Colloidal suspension stability and rheology were measured to evaluate the design factor effects on the formation of soot and subsequent effects on oil thickening. The Mack EM6-285 engine produced less soot, less oil viscosity growth, and less oxidation than the GM 6.2L engine.

Extended drain of axle and transmission lubricants has gained wide acceptance in both passenger car and commercial vehicle applications. Understanding how the lubricant changes during extended drain operations is crucial in determining appropriate lubricants and drain intervals for these applications. A suitable aging screen test with an established relationship to field performance is essential. Over the years numerous methods have been studied (DKA, GFC, ISOT, ASTM L-60) with varying degrees of success1,2,3. Current methods tend to be overly severe in comparison to field experience, hence the need for further work in this area. As a result of recent work, a lubricant aging test method has been developed which shows good correlation with field experience, giving us an effective tool in the development of long drain oils.

Specific frictional properties are essential to provide correct and pleasurable shifting in a manual transmission. Synchroniser rings are being manufactured from an increasingly wider range of materials, and it is important to understand synchroniser-additive interactions in order to develop tailored lubricants that provide the desired frictional performance. This paper describes a study of the interaction of various friction modifier additives with a range of synchroniser materials in order to better understand the potential to develop lubricants that provide optimal frictional performance across a wide range of manual transmission-synchroniser systems.

Specific frictional properties are essential to provide correct and pleasurable shifting in a manual transmission. Synchroniser rings are being manufactured from an increasingly wider range of materials, and so it is important to understand synchroniser-additive interactions in order to develop tailored lubricants that provide the desired frictional performance. This paper describes a study of the interaction of various friction modifier additives with a range of synchroniser materials in order to better understand the potential to develop lubricants that provide optimal frictional performance across a wide range of manual transmission-synchroniser systems. This presentation will outline the results of testing fluids with a range of synchroniser materials and will be followed by a future paper that will describe details of the fluids and analysis of their interactions with the different synchroniser surfaces.

In API engine oil licensing, candidate oils must meet the performance requirements of category defined engine tests. While API category engine tests are developed to target a theoretical performance standard, it is rare that the cost to test and approve oils is understood. Given that engine tests are an integral part of oil evaluation, understanding of engine test value is necessary. Therefore, measurements of value are presented as Unbiased Engine Test Evaluation (UETE). UETE evaluates an engine test's draw on time and money resources by estimating the average number of tests required before a candidate oil will pass the category defined engine tests. A pilot study using the API CH-4 Category is presented.

This work presents a follow-up to previous efforts by the authors to investigate the susceptibility of gasoline direct injection (g-di) engines to deposit formation and the effect of those deposits on vehicle performance. A series of injector keep clean and clean up tests in base and additized fuels utilizing the ASTM D 5598 cycle provided a range of injector fouling levels. It is found that the g-di engine employed here is more susceptible to injector deposits than even the sensitive port fuel injected (PFI) engine used as industry reference in the D 5598 procedure. Injector keep clean and clean up performance of several representative deposit control chemistries are evaluated. In order to determine the effect of injector fouling on performance, emissions and driveability tests are performed on the vehicles at varying levels of injector fouling. Regulated emissions, particulates, fuel consumption and driveability are all shown statistically to be linked to injector fouling.

The International Lubricant Standardization and Approval Committee (ILSAC) GF-2 specification requires Passenger Car Motor oils to provide enhanced fuel economy in a modern low friction engine (ASTM Sequence VIA). The durability of this fuel economy improvement is becoming increasingly important and will be address in the successor to the Sequence VIA, the Sequence VIB, which is currently under development for ILSAC GF-3. Previous investigations have indicated that the choice of detergent system and friction modifier has a large impact on the fuel economy of a lubricant. As a result of a study undertaken to further investigate these effects in a 1994 Ford Crown Victoria running the EPA Federal Test Procedure, a significant impact on tailpipe emissions was discovered. Detergent system affected both regulated emissions (hydrocarbon (HC), carbon monoxide (CO), and oxides of nitrogen (NOx) emissions), and non-regulated emissions (carbon dioxide emissions).

Low temperature flow improvers help refiners meet diesel fuel cold flow specifications and optimize profits. However, some additives, cloud point depressants in particular, are under scrutiny since there have been cases where they interacted with other cold flow improvers and became less effective at depressing the cloud point of the diesel fuel[1]. This second paper in a series of studies[2] examines what effect mixing cloud point depressed diesel fuel with other cloud point depressed diesel fuel or with diesel fuel diluted with kerosene will have on the resultant fuel mixture's cloud point. The data show that cloud point depressants can be used safely and effectively with kerosene blended fuels and in conjunction with other cloud point depressants.

Water-emulsified diesel fuel technology has been proven to reduce nitrogen oxides (NOx) and particulate matter (PM) simultaneously at relatively low cost compared to other pollution-reducing strategies. The value of this technology is that it requires absolutely no engine adjustments or modifications to reduce harmful emissions. Technologies that break the NOx -particulate trade-off are virtually non-existent, therefore understanding how the water contained in an emulsified fuel can reduce both NOx and PM simultaneously is critical. To understand this phenomenon, emulsified fuels with varying water levels (0 to 20%) were evaluated in a multi-cylinder marine engine using three different injection timings. This testing in an actual engine confirms that as the water level is increased the amount of NOx and PM are reduced without compromising engine performance.

Intentionally adding water to oil, in the laboratory, provides an indication of the oil's ability to tolerate the presence of water. Various characteristics, such as emulsion, haze or separation, may be observed. Some blends of oil and water have been shown to form structures when left undisturbed. A visual, qualitative, storage test is capable of detecting this phenomenon as the presence or absence of structure. However, the time frame of formation can be on the order of days or weeks and is sensitive to handling and temperature effects. Quantitative methods are required for any evaluation of chemistry, temperature and handling effects on the rate and strength of structure formation. This paper describes rheological and electrical methods which directly and indirectly measure the tendency to form a structure at the molecular level, yielding rate of formation and strength information.

The intent of industry and OEM factory fill oil specifications is to ensure lubricant pumping performance at low temperatures through rheological measurements using the Mini Rotary Viscometer and Scanning Brookfield tests. Often these tests provide conflicting information, yet lubricant formulations must be optimized to meet requirements of both tests. At the root of this issue is how test information is interpreted, since ultimately it is that interpretation that influences how specifications are set. In this paper, we focus on understanding the Scanning Brookfield test's gelation index which is part of ILSAC GF-2 and GF-3 specifications; our objective is to understand what is measured and its relation to meaningful low temperature lubricant performance. We approach this objective by measuring the low temperature rheology of mineral oils and lubricants formulated from these oils.

To meet increasingly stringent emissions and fuel economy regulations, many Original Equipment Manufacturers (OEMs) have recently developed and deployed small, high power density engines. Turbocharging, coupled with gasoline direct injection (GDI) has enabled a rapid engine downsizing trend. While these turbocharged GDI (TGDI) engines have indeed allowed for better fuel economy in many light duty vehicles, TGDI technology has also led to some unintended consequences. The most notable of these is an abnormal combustion phenomenon known as low speed pre-ignition (LSPI). LSPI is an uncontrolled combustion event that takes place prior to spark ignition, often resulting in knock, and has been known to cause catastrophic engine damage. LSPI propensity depends on a number of factors including engine design, calibration, fuel properties and engine oil formulation. Several engine tests have been developed within the industry to better understand the phenomenon of LSPI.

For a diesel lubricant to meet the new Mack EO-K/2 specification, it must be effective in preventing excessive viscosity increase during the 150-hour Mack T-7 test. The severity of this test is shown to be highly dependent upon fuel chemistry and injection timing. A comparison of various lubricant formulations in the Mack T-7 engine run with a given fuel suggests that nitrogen-containing succinimide dispersants, dispersant viscosity improvers, and supplemental ash in the form of overbased sulfonate detergents are effective in controlling viscosity increase. Crankcase oil thickening follows a modified form of Brinkman’s equation and can be predicted from measured values of soot particle size and concentration. Basic lubricant additives are shown to prevent particle size growth by adsorption on to the acidic soot surface, thereby interrupting soot aggregation and retarding oil thickening.

In the first paper in this series (1)*, the extent of oil thickening for a given lubricant in the Mack T-7 engine test was found to be influenced by fuel composition. Based upon the knowledge that thickening is due to the accumulation and aggregation of soot in the oil, a set of experiments has been carried out to identify relationships between fuel chemistry and the oil thickening tendency of soot formed by fuel combustion. Three commercial diesel fuels were treated with chemical combustion aids and/or organic sulfur, and both short-duration and full-length tests were run in a Mack T-7 engine fitted with a filter designed to collect soot from the exhaust stream. A model describing the complex effects of fuel chemistry on the oil thickening process is proposed in which fuel sulfur content is shown to influence soot content of the lubricant after ISO hours of engine operation.

The relationship between 76 Racing and NASCAR allowed 76 Lubricants Company to work closely with Richard Childress Racing (RCR) and The Lubrizol Corporation in the development of oil screening and analytical test procedures which permit rapid evaluation of potential top-tier NASCAR race oils. The oils were designed to meet the challenge of increasingly severe engine operating parameters. This paper will discuss dynamometer testing and how properties of the oil such as viscosity grade, base fluid, and additives affect engine durability in the dynamometer test program and performance at the track in NASCAR Winston Cup Racing. Areas of growing concern include the cam/lifter contact, ring/liner contact, wrist pin/pin bore and wrist pin bushing contacts. Racing lubricants must withstand these harsh conditions for periods of 3-4 hours of continuous running.

Information relative to oil thickening has been developed in road tests. Typical operating temperatures, as well as the length of time required to thicken oils in these tests, are described. A laboratory test procedure has been developed that shows a good degree of correlation with this field service. The effect of test conditions such as jacket temperature and piston ring design on oil thickening in the laboratory are described.