Search Results

Vehicles equipped with one or several functions of Advanced Driver Assistant System (ADAS) and autonomous driving (AD) technology are more mature and prevalent nowadays. Vehicles being smarter and driving being easier is an unstoppable trend. In the near future, intelligent vehicles will be mass produced and running on the road. However, before the mass-production of intelligent vehicles, a lot of experimental tests and validations need to be carried out to insure the safety and reliability of ADAS and AD technology. Although the road test of real vehicles is the most reliable and accurate test method, it cannot meet the need of rapid development of technology research due to high time and financial cost. Therefore, a high-efficient design and evaluation methodology for ADAS and AD development and test is a must. In this paper, a virtual co-simulation platform based on MATLAB/Simulink, OpenModelica and Unity 3D game engine (MOMU) is proposed.

Safety is the cornerstone for Advanced Driver Assistance Systems (ADAS) and Autonomous Driving Systems (ADS). To assess the safety of a traffic situation, it is essential to predict motion states of traffic participants in the future with mathematic models. Accurate vehicle trajectory prediction is an important prerequisite for reasonable traffic situation risk assessment and appropriate decision making. Vehicle trajectory prediction methods can be generally divided into motion model based methods and maneuver model based methods. Vehicle trajectory prediction based on motion models can be accurate and reliable only in the short term. While vehicle trajectory prediction based on maneuver models present more satisfactory performance in the long term, these maneuver models rely on machine learning methods. Abundant data should be collected to train the maneuver recognition model, which increases complexity and lowers real-time performance.

In this paper, a novel method is proposed to establish the vehicle yaw stability criterion based on the sideslip angle-yaw rate (β-r) phase plane method. First, nonlinear two degrees of freedom vehicle analysis model is established by adopting the Magic Formula of nonlinear tire model. Then, according to the model in the Matlab/Simulink environment, the β-r phase plane is gained. Emphatically, the effects of different driving conditions (front wheels steering angle, road adhesion coefficient and speed) on the stability boundaries of the phase plane are analyzed. Through a large number of simulation analysis, results show that there are two types of phase plane: curve stability region and diamond stability region, and the judgment method of the vehicle stability domain type under different driving conditions is solved.

Vehicle sideslip angle estimation is of great importance to the vehicle stability control as it could not be measured directly by ordinary vehicle-mounted sensors. As a result, researchers worldwide have carried out comprehensive research in estimating the vehicle sideslip angle. First, as the attitude would affect the acceleration information measured by the IMU directly, different kinds of vehicle attitude estimation methods with multi-sensor fusion are presented. Then, the estimation algorithms of the vehicle sideslip angle are classified into the following three aspects: kinematic model based method, dynamic model based method, and fusion method. The characteristics of different estimation algorithms are also discussed. Finally, the conclusion and development trend of the sideslip angle estimation are prospected.

In order to avoid the influence of the change of the camera pitch angle and the variation of the height of the ground on the ranging accuracy, improve the real-time performance of the algorithm by substituting the current widely-used monocular vision ranging algorithm which builds the optical model based on the shadow of the vehicle floor and the lane line, as well as avoid the classification of vehicle detection, a vehicle distance measurement algorithm based on monocular vision and license plate width is established. Firstly, the target image acquisition and preprocessing are studied. Then the paper studies the license plate image location segmentation method based on accelerated template matching. On this basis, the algorithm for obtaining the ratio of license plate width to image width is studied, and the function of vehicle distance and license plate ratio width is established.

Water content estimation is a key problem for studying the PEM fuel cell. When several hundred fuel cells are connected in serial and their active surface area is enlarged for sufficient power, the difference between cells becomes significant with respect to voltage and water content. The voltage of each cell is measurable by the cell voltage monitor (CVM) while it is difficult to estimate water content of the individual. Resistance of the polymer electrolyte membrane is monotonically related to its water content, so that the new online high frequency resistance (HFR) measurement technique is investigated to identify the uniformity of water content between cells and analyze its sensitivity to operating conditions in this paper. Firstly, the accuracy of the proposed technique is experimentally validated to be comparable to that of a commercialized electrochemical impedance spectroscopy (EIS) measurement equipment.

Crashworthiness is one of the most important performances of vehicles, and the front rails are the main crash energy absorption parts during the frontal crashing process. In this paper, the front rail was simplified to a thin-walled beam with a cross section of single-hat which was made of steel and aluminum. And the two boards of it were connected by riveting without rivets. In order to optimize its crashworthiness, the thickness (t), radius (R) and the rivet spacing (d) were selected as three design variables, and its specific energy absorption was the objective while the average impact force was the constraint. Considering the error of manufacturing and measurements, the parameters σs and Et of the steel were selected as the uncertainty variables to improve the design reliability. The algorithm IP-GA and the approximate model-RBF (Radial Basis Function) were applied in this nonlinear uncertainty optimization.

With the increase of motor speed and the deterioration of operating environment, it is more difficult to predict the transient temperature field (TTF). Meanwhile, it is difficult to obtain the temperature test dataset of key nodes under various complete road conditions, so the cost of bench test or real vehicle test is high. Therefore, it is of great significance to establish a high fidelity, lightweight temperature prediction model which can be applied to real vehicle thermal management for ensuring the safe and stable operation of motor. In this paper, a physical model simulating electromagnetic-heat-flow multi-physical coupling of permanent magnet synchronous motor (PMSM) in electric drive gearbox (EDG) is established, and the correctness of the model is verified by the actual EDG bench test.

Estimating the motion state of peripheral targets is a very important part in the environment perception of intelligent vehicles. The accurate estimation of the motion state of the peripheral targets can provide more information for the intelligent vehicle planning module which means the intelligent vehicle is able to anticipate hazards ahead of time. To get the motion state of the target accurately, the target’s range, velocity, orientation angle and yaw rate need to be estimated. Three-dimensional high-resolution automotive millimeter wave radar can measure radial range, radial velocity, azimuth angle and elevation angle about multiple reflections of an extended target. Thus, the three-dimensional range information and three-dimensional velocity information can be obtained. With multiple three-dimensional high-resolution automotive millimeter-wave radar, it is possible to measure information in various directions of a target.

Highly accurate parking slot detection methods are crucial for Automated Valet Parking (AVP) systems, to meet their demanding safety and functional requirements. While previous efforts have mostly focused on the algorithms’ capabilities to detect different types of slots under varying conditions, i.e. the detection rate, their accuracy has received little attention at this time. This paper highlights the importance of trustworthy slot detection methods, which address both the detection rate and the detection accuracy. To achieve this goal, an accurate slot detection method and a reliable ground-truth slot measurement method have been proposed in this paper. First, based on a 2D laser range finder, datapoints of obstacle vehicles on both sides of a slot have been collected and preprocessed. Second, the Density-Based Spatial Clustering of Applications with Noise (DBSCAN) algorithm has been improved to efficiently cluster these unevenly-distributed datapoints.

It is becoming an increasingly important issue to improve NVH performance of electric drive motor for electric vehicle as the market grows rapidly. The correlation between stiffness of rear cover of motor, rotor eccentricity and noise of an electric drive is discussed in this paper which was few mentioned before. Poor stiffness of bearing chamber of rear cover may cause rotor eccentricity, which would lead to additional orders of electromagnetic noise. Stiffness optimization model of rear cover of motor was established, and the Optistruct of Hyper works software was used to improve stiffness as well as mode frequency by designing circular and radial ribs to surround bearing chamber of rear cover under guidance of topology. As compared to basis model with same mass, the 1st and 2nd strict mode frequencies of optimized rear cover separately increased by 11% and 12.5% with numerical simulations.

Carbon fiber reinforced plastic (CFRP) composite materials have gained particular interests due to their high specific modulus, high strength, lightweight and perfect corrosion resistance. However, in reality, CFRP composite materials cannot be used alone in some critical places such as positions of joints with hinges, locks. Therefore, metal reinforcements are usually necessary in local positions to prevent structure damage. Besides, if uncertainties present, obtained optimal structures may experience in failures as the optimization usually pushes solutions to the boundaries of constraints and has no room for tolerance and uncertainties, so robust optimization should be considered to accommodate the uncertainties in practice. This paper proposes a mixed topology method to optimize metal and carbon fiber reinforced plastic composite materials simultaneously under nondeterministic load with random magnitude and direction.

X-in-the-loop (XiL) framework is a new validation concept for vehicle product development, which integrates different virtual and physical components to improve the development efficiency. With XiL platform the requirements of reproducible test, optimization and validation, in which hardware, equipment and test objects are located in different places, could be realized. In the view of different location and communication form of hardware, equipment and test objects, time delay problem exists in the XiL platform, which could have a negative impact on development and validation process. In this paper, a simulation system of time delay prediction and compensation is founded with the help of BP neural network and RBF neural network. With this simulation system the effect of time delay in a vehicle dynamic model as well as tests of geographically distributed vehicle powertrain system is improved during the validation process.

Several failure criteria and stiffness degradation laws for composite materials are summarized and compared in terms of precision and convenience of use. The 2D/3D Hashin failure criteria are coupled with the stiffness degradation rules provided by Tan, Tserpes and Zinoviev. Three new failure models including 2D Hashin-Tan, 3D Hashin-Tser and 3D Hashin-Zin are presented for CFRP materials. The above three models were coded and incorporated into the ABAQUS software by user subroutines, among which model 2D Hashin-Tan and model 3D Hashin-Tser were programmed using the implicit algorithm VUSDFLD while model 3D Hashin-Zin was coded using the explicit algorithm VUMAT. Experiments of uniaxial tension and three-point bending were performed. A single element subjected to uniaxial tension and three-bending were simulated to check the function and precision of the new models.

Lithium ion battery is considered as one of the most possible energy storage equipment for new energy vehicles (EV, HEV, etc.) because of the advantages of long cycle life, high power density and low self-discharge rate. However, under freezing condition high power battery suffers of significant performances losses. For example, they would suffer from significant power capability losses and poor rate performance, which would restrict the availability to delivery or to gain of high current in transient conditions. To evaluate those performance drawbacks and to make an efficient design, good mathematical models are required for system simulation especially for battery thermal management. In this paper, a three-dimensional homogenization thermal model of a 20 Ah prismatic lithium ion battery with LiFePO4 (LFP) cathode is described.

The multi-body dynamics simulation and physical iteration were carried out based on the 4-channel road simulation bench, the solution of fatigue test bench which was suitable for cab with frame and suspension was designed. Large load and displacement above the suspension can be loaded on the test bench, and the same weak position of cab exposed on the road test can be assessed well on the fatigue test bench. The effectiveness of the bench test solution was verified though comparative study. And it has important reference for the same type of cab assembly with suspension in the fatigue bench test. According to the durability specifications of cab assembly, a multi-body dynamics model with a satisfactory accuracy was built. And the fixture check and virtual iteration analysis were used to verify the effectiveness of the solution. According to the road load signal analysis and multi-body dynamics analysis results, the test bench with linear guide and spherical joint was built.

Centrifugal Pendulum Vibration Absorber (CPVA for short) is used to absorb torsional vibrations caused by the shifting motion of the engine. It is increasingly used in modern powertrains. In the research of the dynamic characteristics of the CPVA, it is necessary to obtain the real motion of the pendulum to compensate the fitting performance of mathematical model. The usual method is to install an angle sensor to measure the movement of the pendulum. On the one hand, the installation of the sensor will affect its movement to a certain extent, so that the measurement results do not match the actual motion. On the other hand, the motion of the pendulum is not only the rotational motion around the rotational axis of the CPVA rotor, but also has translation relative to it. As a result, it is difficult to obtain accurate motion only by the angle sensor. We proposed a non-contact centrifugal pendulum motion measurement method.

There are often a large number of design variables and responses in suspension hard point optimization design. The traditional optimization strategy integrating heuristic algorithm and simulation model is not applicable due to its low efficiency. To solve optimization problems with huge number of design variables and responses, a multi-objective optimization framework combined heuristic optimization algorithm with multi-objective decision-making method is developed. Specifically, the multi-objective optimization was performed by dividing the problem into two independent sub-problems of multi-objective optimization and multi-objective decision-making. Further, to reduce the number of sample points required for building a surrogate model, a two-stage multi-objective optimization is proposed.

To analyze the K&C (kinematics and compliance), handling and stability performance of the vehicle chassis, some simulations are usually performed using a multi-body dynamics software named ADAMS. This software introduces assumptions that simplify the components of the suspension as rigid bodies. However, these assumptions weaken the accuracy of the simulation of ADAMS. Therefore the use of flexible bodies in K&C and handling and stability simulation in ADAMS is needed to conduct more precise suspension system designs. This paper mainly analyses the influences of the subframe flexibility on handling and stability simulation in ADAMS/Car. Two complete vehicle models are built using ADAMS/Car and Hypermesh. The only difference between the two models is the subframe of the front McPherson suspension. One of the subframes is simplified as a rigid body. The other one is a flexible body built using the MNF file from Hypermesh.

In order to explore approaches for improving object detection accuracy in intelligent vehicle system, we exploit super-resolution techniques. A novel method is proposed to confirm the conjecture whether some popular super-resolution networks used for environmental perception of intelligent vehicles and robots can indeed improve the detection accuracy. COCO dataset which contains images from complex ordinary environment is utilized for the verification experiment, due to it can adequately verify the generalization of each algorithm and the consistency of experimental results. Using two representative object detection networks to produce the detection results, namely Faster R-CNN and YOLOv3, we devise to reduce the impact of resizing operation. The two networks allow us to compare the performance of object detection between using original and super-resolved images. We quantify the effect of each super-resolution techniques as well.