Search Results

The wear mechanisms of the methanol engine were studied using dynamometer tests. Formic acid from methanol combustion mixes with the lubricant oil and attacks the metal surfaces. The iso tacho prorissis method was successfully applied to analyze the formic acid content of the used oil. A large amount of condensed water is also formed by methanol combustion and accelerates the wear. Wear can be effectively reduced by shortening lubricant oil change intervals, by using a special oil and by durable surface treatment of engine parts.

Diamond-like carbon (DLC) coating has excellent properties like high hardness and low friction. So it has attracted considerable attention in recent years as a low-friction coating material. However, some DLC coatings display increased wear in oil containing Mo-DTC (Molybdenum-dithiocarbamates). Wear analyses of sliding surface after block-on-ring tests were conducted suggest that the decomposition product from Mo-DTC, MoO3, reacts with active sites in the DLC to promote the wear of DLC.

Display devices are required to have some fundamental functions which are brightness & gradation, colorfullness, resolution & sharpness, response time, and suitable size of the picture. Since the CRT (Cathode Ray Tube) is superior to the other display devices in these requirements, it can offer much information efficiently and effectively. Their visibility should not be evaluated only on the basis of some standards for office automation systems. From the point of view of human factors, visibility investigations of the CRTs for automobiles are examined. In this paper the relationship between the chromaticity difference and the luminance contrast for drivers to read the picture easily, and the luminance of the background in the CRTs for drivers not to be dazzled in the nighttime driving are clarified.

Grip feeling is an important facet in vehicle dynamics evaluation from a driver satisfaction and enjoyment standpoint. To improve grip feeling, we analyzed the subjective comments from test driver's about grip feeling and an evaluated human sensitivity to lateral motion. As a result, we found that drivers evaluate transient grip feeling according to the magnitude of lateral jerk. Next, we analyzed what vehicle parameters affect lateral jerk by using theoretical equations. As a result, we found that cornering power is an important parameter, especially the cornering power of rear tires as they can be create larger lateral jerk than can front tires.

Improvement of vehicle dynamics in limit cornering have been studied. Simulations and tests have verified that vehicle stability and course trace performance in limit cornering have been improved by active brake control of each wheel. The controler manages vehicle yaw moment utilizing difference braking force between left and right wheels, and vehicle deceleration utilizing sum of braking forces of all wheels.

In-wheel motors (IWM) will be a key technology that contributes to the popularization of electric vehicles. Combining electric drive with IWM enables both good vehicle dynamics and a roomy interior. In addition, the responsiveness of IWM is also capable of raising dynamic control performance to an even higher level. IWM enable vertical body motion control as well as direct yaw control, electric skid control, and traction control. This means that IWM can replace most control actuators used in a vehicle chassis. The most important technology for IWM is to enable the motor to coexist with the brake and the suspension arms inside the wheel. The IWM drive unit described in this paper can be installed with a front double wishbone suspension, the most difficult configuration.

In order to develop the valve rocker arm material for the new type engine, we investigated various materials whose chemical compositions were selected using 30% chromium cast iron, which had shown good results in screening evaluation tests, as the basis. High chromium cast irons are well known for their abrasive wear resistance, but it has been very difficult to apply them for use as rocker arm material because their machinability is very poor, and because it is difficult for them to have a regular microstructure. In this paper, both the manufacturing method for the rocker arm which decreases the disadvantages that high chromium cast iron have and the rocker arm material best suited for this method are described.

Toyota has developed a new system, which uses integrated control of powertrain by PowerTrain Management (PTM), in order to improve driving comfort and reliability. This system is currently in use on Lexus's new LS460. This system is composed of 4 parts: a generation part, a mediating part, a modification part and a distribution part. In each part, processes are based on drive power and torque. In the generation part, requests from a programmed model driver, Driving Support Computer and Vehicle Dynamics Integrated Management (VDIM) are generated and expressed by drive power. In the mediating part, most suitable vehicle drive power was selected among the requests. In the modification part, the selected request is modified using a programmed powertrain model, which considers internal combustion engine condition and powertrain response and transmission's tolerance. In the distribution part, optimized engine torque and gear ratio are processed.

TOYOTA MOTOR CORPORATION had developed the world's first microprocessor controlled suspension system, Toyota Electronic Modulated Suspension (TEMS), which is now being offered on the Toyota Soarer from Feb. '83. This system consists of sensors, switches, electronic control unit (ECU), actuators and shock absorbers. TEMS uses a microprocessor to adjust the damping forces of the front and rear shock absorbers. As a result, suspension can be tuned in two stages (hard and soft cushioning) and driver can choose three control modes (AUTO, SPORT, NORMAL). In AUTO mode, the TEMS system has achieved attitude controls (i.e. squat control, roll control and nosedive control). The TEMS system achieved a 15 - 30% decrease of squat, a 20 - 30% decrease of roll angle, a 10 - 30% decrease of nose-dive and a 30 - 40% decrease of shift-squat.

Toyota has developed a new full time 4WD system, called “EC-HYMATIC” or Electronically Controlled - HYdraulic Multi-plate clutch Active Traction Intelligent Control. This system permits an automatic torque transfer, depending on driving conditions, for front and rear wheels under control of the speed difference between the two. The system developed consists of a center differential, a speed difference control clutch system employing multi-plate clutch, and a gear set for rear axle drive. The speed difference control clutch system is controlled by a unique electro-hydraulic system using a microcomputer. An extensive use of computer simulations and vehicle test and evaluation has successfully developed an appropriate control strategy for the clutch system. The new 4WD system, EC-HYMATIC, considerably improves handling characteristics, traction performance and stability of a 4WD vehicle.

The torque converter clutch slip control system adopted in the Toyota A541E automatic transaxle engages the torque converter clutch by applying a steady slip speed to prevent the torque fluctuation of the engine to be transmitted to the drivetrain while enhancing the transmission efficiency of the torque converter. The feedback controller of the slip speed adopts the H∞ (H-Infinity) control theory which offers a high level of robust stability, and is the first of its kind in a mass produced component. As a result, a highly accurate and reliable system has been realized, contributing to large-scale fuel economy.

This research developed a new measurement technology for thermal analysis of the heat radiation from a hybrid transaxle case surface to the air and improved the heat radiation performance. This heat flux measurement technology provides the method to measure heat flux without wiring of sensors. The method does not have effects of wiring on the temperature field and the flow field unlike the conventional methods. Therefore, multipoint measurement of heat flux on the case surface was enabled, and the distribution of heat flux was quantified. To measure heat flux, thermal resistances made of plastic plates were attached to the case surface and the infrared thermography was used for the temperature measurement. The preliminary examination was performed to confirm the accuracy of the thermal evaluation through heat flux measurement. The oil in the transaxle was heated and the amount of heat radiation from the case surface was measured.

This paper describes an analysis of the rise in timing belt temperature occuring under high engine speed operation that was made to establish the cause of heat deterioration of the belt materials. Surface temperatures of the belt were accurately measured by correcting thermo-vision detected radiations to eliminate environmental radiation. The temperature profile of a belt cross-section was obtained by a specially developed thermo-couple device. The experimental results indicated that heat generated by the belt contributes significantly to the temperature rise and that the primary cause of the heat generation is bending hysteresis of the belt cords. In addition, a description is made of a method of calculating the rate of heat generation in the belt. In this simulation method, the energy dissipated as heat is calculated from the bending strains and loss moduli of the belt materials. Calculated results were found to agree well with experimental results.

We have developed the world's first 8-speed automatic transmission for transverse FWD/4WD vehicles. The aim of this new automatic transmission was to achieve world-class fuel economy while offering both smooth gear shift and sporty shift feeling suitable for luxury cars. This has been accomplished using wide spread gear ratio, outstanding low drag components and highly efficient hydraulic control system. In addition, we have achieved the compactness similar to current 6-speed automatic transmission by adopting new gear train and compact clutch layout. In this paper, the detail of this automatic transmission is introduced.

This paper describes the preliminary development of an on-board integration network for vehicle dynamics. The underlying philosophy is explained and the basic requirements are set forth. A design conforming to these requirements is presented and the experiments conducted to optimise the physical layer are described. An original token passing protocol is proposed for the access method and evaluated in comparison with the contention method by means of a specially devised simulation system.

In recent years, advanced technology has become more and more important in the design of automobiles. Therefore, if we wish our products to continue to display their full potential to the people who buy them, thus ensuring customer satisfaction with our products, we must, even in the area of after-soles service, ensure that the technical proficiency and knowledge of our technicians will continue to keep pace with advances in technology. To do this, we must carry out effective “high-tech” training for our dealer workshops this is our present and future challenge Toyota's technical service training system is now applied to some 50, 000 service technicians in around 10, 000 workshops throughout the world, and the proposed report will introduce this system and give some actual examples of technical training that is actually carried out.

A new automotive interior component material, TSOP-5 has been developed by refining the technology utilized to develop TSOP-1, the high modulus and high flow material for bumper covers. This new interior component material has excellent molding capability (MI=30dg/min.) yet still maintains high impact resistance which enables the material to be used in areas such as the dash board as well as trim covers requiring to meet the FMVSS 214, the new side impact regulation or the FMVSS 201, the new soft upper trim regulation.

The change of the fuel flow rate in an injector with mileage accumulation causes poor drivability and exhaust emission deterioration in Otto-type methanol fueled vehicles with a multi-point fuel injection system. This is one of the serious problems which needs to be solved for the practical use of methanol fueled vehicles. The investigation results reveal that the wear of contact surfaces between a valve needle and a valve body increases the resistance force for valve needle movement and causes the change of dynamic fuel flow rate in the injector. The effects of several countermeasures to solve this problem are evaluated.

As the demand for improved fuel economy increases and new CO2 regulations have been issued, aerodynamic drag reduction has become more critical. One of the important factors to consider is cooling drag. One way to reduce cooling drag is to decrease the air flow volume through the front grille, but this has an undesirable impact on cooling performance as well as component heat load in the under-hood area. For this reason, cooling drag reduction methods while keeping reliability, cooling performance and component heat management were investigated in this study. At first, air flow volume reduction at high speed was studied, where aerodynamic drag has the greatest influence. For vehicles sold in the USA, cooling specification tends to be determined based on low speed, while towing or driving up mountain roads, and therefore, there may be extra cooling capacity under high speed conditions.

Recently, the California Air Resources Board (CARB) has proposed a new set of evaporative emissions and “Useful Life” standards, called LEVII EVAP regulations, which are more stringent than those of the enhanced EVAP emissions regulations. If the new regulations are enforced, it will become increasingly important for the carbon canister to reduce Diurnal Breathing Loss (DBL) and to prevent deterioration of the canister. Therefore, careful studies have been made on the techniques to meet these regulations by clarifying the working capacity deterioration mechanism and the phenomenon of DBL in a carbon canister. It has been found that the deterioration of working capacity would occur if high boiling hydrocarbons, which are difficult to purge, fill up the micropores of the activated carbon, and Useful Life could be estimated more accurately according to the saturated adsorption mass of the activated carbon and the canister purge volume.