Search Results

Finite element aodels have been developed to analyze drive line and suspension vibration. For the analysis of booming noise, we have addressed the optimization of the differential gear carrier mounting system by using a virtual system and realization of it considering many constraints. To reduce the differential whine noise, a simulation method considering the transmitting error of the differential gear was applied. And we have approached for the subtle arrangements of many structural resonances with detail research of the drive line and suspension. For the reduction of road noise, we adopted the approach of shifting the node of the rear suspension member mode.

The SEA model of wind noise requires the quantification of both the acoustic as well as the turbulent flow contributions to the exterior pressure. The acoustic pressure is difficult to measure because it is usually much lower in amplitude than the turbulent pressure. However, the coupling of the acoustic pressure to the surface vibration is usually much stronger than the turbulent pressure, especially in the acoustic coincidence frequency range. The coupling is determined by the spatial matching between the pressure and the vibration which can be described by the wavenumber spectra. This paper uses measured vibration modes of a vehicle window to determine the coupling to both acoustic and turbulent pressure fields and compares these to the results from an SEA model. The interior acoustic intensity radiating from the window during road tests is also used to validate the results.

Toyota Motor Corporation has developed a new four-speed automatic transaxle U140E named “Super ECT”. The U140E has achieved compactness which enables it to mount on many new platforms, achieved high efficiency, which contributes to improve fuel economy, and it achieved good shift feeling, response, and reduce noise. This paper shows the major features and performance of the U140E.

Eliminating brake squeal generated during brake application is an important task for the improvement of comfort in the vehicle. There has been a lot of research made on the problem of brake squeal in the past. And most of the papers presented elaborate on low frequency brake squeal (2-3kHz). However, brake squeal has often the high-frequency vibration. For this reason, we have made research into the high-frequency brake squeal (5-10kHz). Double-Pulsed Laser Holography is a useful method for visualizing small vibration of brake components during brake squeal generation. The results obtained using Holographic Interferometry show the rotaing disc vibrates in the bending mode with diametral nodes. Consequently, we think that the modification of brake disc can eliminate brake squeal, which is caused by self-excited vibration. Then we have calculated natural frequency and its vibration mode of a circular-plate added mass.

It is very important for the vehicle comfort quality to eliminate brake noise. The brake noise can be defined into two phenomena: One is the high-frequency brake squeal (frequency 1-15kHz), we have presented in 1989 SAE Congress(890864) * (2),and the another is the low-frequency brake groan (frequency 200-500Hz). In this paper,the brake groan has been discussed by constituting the theoretical model,in order to clarify the cause of disc brake groan noise. According to the previous study(3), the groan noise has been occurred by the increase of the disc temperature which has influenced on the disc width and the disc material. On the other hand, the groan noise can be observed in the condition of atmosphere temperature indeed. So that the precise phenomenon and cause should be defined. After observing the groan noise on the test bench, we have constructed the theoretical model and taken the numerical method.

The finite element method (FEM) is effective for analyzing brake squeal phenomena. Although FEM analysis can be used to easily obtain squeal frequencies and complex vibration modes, it is difficult to identify how to modify brake structure design or contact conditions between components. Therefore, this study deals with a practical design method using sensitivity analysis to reduce brake squeal, which is capable of optimizing both the structure of components and contact conditions. A series of analysis processes that consist of modal reduction, complex eigenvalue analysis, sensitivity analysis and optimization analysis is shown and some application results are described using disk brake systems.

An experimental simulation method has been developed for predicting the noise and vibration characteristics of a complete vehicle when body frame stiffness is changed. This method was developed by means of an improved transfer function synthesis method. Advantages over numerical simulation methods, such as finite element analysis include dramatic reductions in computation time. This experimental method is also very easy to carry out with a few measurement data. By applying this method to investigate the effects of stiffness changes of different vehicle components on low frequency road noise, effective ways of reducing road noise were proposed in the first stage of vehicle development.

This research proposes an automatic measuring method for the impulse noise of the valve system in engine production line. This research is composed of the following two parts. (1) The most suitable method for indicating the impulse noise of the valve system - the representative characteristic values - is selected from the general measuring methods for impulse noise. As the result, the crest factor in the frequency band above 1kHz became optimal. (2) By detailed sensory characteristic analysis it was found that impulse noise can be heard better with increasing frequency and that there is little influence in the frequency band with the same frequency as the background noise. Thus the crest factor was obtained for each frequency, and the sensory test for the impulse noise of the valve system is deduced by this linear coupling. As the result of multiple reguression analysis, a high accuracy prediction equetion with a multiple correlation coefficient of 0.91 has been obtained.

In order to reduce the interior noise of a vehicle with a four-cylinder engine, investigations were made using finite element and vector methods, acoustic intensity testing and holography technique. The investigation resulted in inclination of the engine mounting, design changes to the front suspension member, a shock absorber engine mounting, structural modifications to reduce body panel vibration and a new engine mounting to insulate high frequency engine vibration.

With the progress of super computers in recent years, a number of studies on “Computational Fluid Dynamics” (CFD) have been carried out, and various schemes for Navier-Stokes equations have been presented. Similar methods have also been applied to automotive engineering - aerodynamics, for exampre - in order to determine flow phenomena. In this paper, the application of numerical simulations to the flow cavitation that occurs in some part of orifices in the vehicle hydraulic system, will be discussed. Authors have developed a CFD program for the clarification of flow phenomena in such orifices. Using the relationship between calculated results and measured results of noise levels in such orifices, a new method for estimation of the occurrence of flow cavitation has also been developed. As a result, a new orifice configuration capable of preventing the cavitation has been designed.

The design of the newly developed Toyota AZ series 4 cylinder engine has been optimized through both simulations and experiments to improve heat transfer, cooling water flow, vibration noise and other characteristics. The AZ engine was developed to achieve good power performance and significantly reduced vibration noise. The new engine meets the LEV regulations due to the improved combustion and optimized exhaust gas flow. A major reduction in friction has resulted in a significant improvement in fuel economy compared with conventional models. It also pioneered a newly developed resin gear drive balance shaft.

This paper describes a new plastic coloring and forming system. The system greatly reduces the time and amount of raw materials necessary for color changes, and eliminates the need for manual cleaning during a color change. This system is well-suited for small-lot production with frequent color changes, as well as for automated production systems. The system is being used by auto parts makers, and is practical in a variety of other fields involved with the coloring and forming of plastics.

Recently, the quietness of the passenger compartment has become an important quality for a vehicle, and as a result, various improvements have been made to reduce the passenger compartment noise level. Particularly engine noise, a major source of interior noise, has been studied for many years and has recently been reduced to an acceptable level. As a result, air intake noise, which was a relatively minor noise source in the past, has rapidly become a noticeable noise source. This paper describes a newly developed air intake system testing apparatus, which enables us to evaluate intake noise at an early stage of engine development and also describes how the new apparatus and approach was used to develop a low-noise air intake system. This apparatus, called the PULSATION SIMULATOR, reproduces intake pulsations in the actual engine using its cylinder head and reproduces intake air flow precisely.

Conventionally, sound insulation materials have been applied to control interior noise above 500 Hz, and damping materials to control interior noise below 500 Hz. In this paper, the noise control component for vehicle panels, which consists of damping material and sound insulation material, is investigated by using a two-degrees-of-freedom system. The investigation shows that sound insulation material can be effective in reducing interior noise below 500 Hz if its stiffness is reduced. This stiffness depends not only on the spring of the material itself but also on its pneumatic spring which is determined by air-flow resistance. This paper concludes with applications of techniques to reduce interior noise below 500 Hz by improving sound insulation materials.

The noise generation mechanism of a direct-acting valve train such as used in sporty and luxury cars was determined for both mechanical and hydraulic tappets through measurements of sound pressure levels and vibrations and the use of computer graphics to observe actual valve and tappet movement. Two phenomena were clarified: chatter at low engine speeds and a mechanical noise at high engine speeds. Further experiments established that the noise of a mechanical tappet can be greatly reduced and its tonal quality improved by optimizing the cam profile and by increasing the acoustic damping ratio of the tappet.

With the advance in modularization of engine parts in recent years, there is increased use of plastic-made products in air intake systems. Plastic-made intake manifolds (Fig. 1) provide many advantages including reduced weight, reduced cost, and lower intake air temperatures. However, these manifolds have one disadvantage when compared with conventional aluminum-made intake manifolds, in that they transmit more noise because of their lower material density. For example, plastic intake manifolds of early development often generate flow noise when the throttle is opened quickly. With conventional aluminum intake manifolds, this flow noise had generated, but was not heard. This flow noise is presumed to be generated because of high-speed airflow generated when the throttle is opened quickly, but the mechanism of this noise generation has not been clarified.

Next generation vehicles driven by motor such as electric vehicles and fuel cell vehicles have no engine noise. Therefore the balance of interior noise is different from the vehicles driven by conventional combustion engine. In particular, road induced noise tends to be conspicuous in the low to middle vehicle speed range, therefore, technological development to reduce it is important task. The purpose of this research is to predict the road induced noise from the signals of sensors adopted for automatic driving for utilizing the prediction result as a reference signal to reduce road induced noise by active noise control (ANC). Using the monocular camera which is one of the simplest image sensors, the road induced noise is predicted from the road surface image ahead of the vehicle by machine learning.

This paper is a study of the On-Board Diagnosis (OBD), a constituent element of the automotive electronic diagnosis system, together with its support functions. With regard to the OBD, we have listed and explained the principles of various diagnostic methods and their advantages and disadvantages. In addition, we have also commented on design factors and concepts. As to the support functions, nameiy diagnostics communication and diagnostic scan tool, drive recorder, and also IT, we have made recommendations on their future development in view of the functional division of roles with respect to the OBD in light of their respective characteristics.

Recently, programmable controllers have been utilized for new equipment on production lines in the automobile industry. However, operators who must use these devices to carry out various operations face difficulties understanding the different methods for programming, ets. of these devices, and for handling the various types of peripheral equipment. In accordance with the increase in the number of PCs, CAD/CAM systems have become requisite for achieving high efficiency in sequence control design. However, poor PC standards prevent their development. In this paper, the development of PC systems, as well as methods for the elimination of problems with standardization, are described. The methods of standardization concern the methods of transmission between the PC and the peripheral equipment, the construction of peripheral equipment and the structure of data in the ladder diagram.

The progress of vehicle electrification has reduced engine noise and the improvement of rear differential gear whine noise has become more important for customer satisfaction. Rear differential gear whine noise is a result of the vibration generated by the transmission error of the gears transmitted to the cabin from various paths. As several components have a contribution, identifying key paths to develop an effective countermeasure becomes time consuming. Operational transfer path analysis (OTPA) is one of the TPA methods to determine the main path and contributing part using only the operational data. However, in cases where many reference points are set on the same frame or body, the contribution becomes similar because of high correlation between the reference data set. As a result, finding the main transfer path becomes difficult.