Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Wear Mechanisms of Methanol Fueled Engine

1985-11-11
852199
The wear mechanisms of the methanol engine were studied using dynamometer tests. Formic acid from methanol combustion mixes with the lubricant oil and attacks the metal surfaces. The iso tacho prorissis method was successfully applied to analyze the formic acid content of the used oil. A large amount of condensed water is also formed by methanol combustion and accelerates the wear. Wear can be effectively reduced by shortening lubricant oil change intervals, by using a special oil and by durable surface treatment of engine parts.
Technical Paper

Valve Rocker Arm Material for Investment Casting

1985-11-11
852203
In order to develop the valve rocker arm material for the new type engine, we investigated various materials whose chemical compositions were selected using 30% chromium cast iron, which had shown good results in screening evaluation tests, as the basis. High chromium cast irons are well known for their abrasive wear resistance, but it has been very difficult to apply them for use as rocker arm material because their machinability is very poor, and because it is difficult for them to have a regular microstructure. In this paper, both the manufacturing method for the rocker arm which decreases the disadvantages that high chromium cast iron have and the rocker arm material best suited for this method are described.
Technical Paper

Using the Modal Response of Window Vibrations to Validate SEA Wind Noise Models

2017-06-05
2017-01-1807
The SEA model of wind noise requires the quantification of both the acoustic as well as the turbulent flow contributions to the exterior pressure. The acoustic pressure is difficult to measure because it is usually much lower in amplitude than the turbulent pressure. However, the coupling of the acoustic pressure to the surface vibration is usually much stronger than the turbulent pressure, especially in the acoustic coincidence frequency range. The coupling is determined by the spatial matching between the pressure and the vibration which can be described by the wavenumber spectra. This paper uses measured vibration modes of a vehicle window to determine the coupling to both acoustic and turbulent pressure fields and compares these to the results from an SEA model. The interior acoustic intensity radiating from the window during road tests is also used to validate the results.
Technical Paper

Thin wall and lightweight cylinder block production technology

2000-06-12
2000-05-0067
The automobile industry currently faces many challenges which may greatly impact on its foundry operations. One of these challenges, consumers'' demand for greater fuel efficiency, can be met by reducing the weight of castings used in automobiles, and minimizing engineering tolerances. In answer to this particular demand, engine foundries have begun to either produce cylinder blocks or other castings with aluminum rather than cast iron. However, if a reduction in weight (thin wall and near-net shaping) can be realized with cast iron, there would be numerous merits from the perspective of cost and compactness and there would be much more flexibility in automotive parts design.
Journal Article

Thermal Flow Analysis of Hybrid Transaxle Surface Using Newly-Developed Heat Flux Measurement Method

2015-04-14
2015-01-1652
This research developed a new measurement technology for thermal analysis of the heat radiation from a hybrid transaxle case surface to the air and improved the heat radiation performance. This heat flux measurement technology provides the method to measure heat flux without wiring of sensors. The method does not have effects of wiring on the temperature field and the flow field unlike the conventional methods. Therefore, multipoint measurement of heat flux on the case surface was enabled, and the distribution of heat flux was quantified. To measure heat flux, thermal resistances made of plastic plates were attached to the case surface and the infrared thermography was used for the temperature measurement. The preliminary examination was performed to confirm the accuracy of the thermal evaluation through heat flux measurement. The oil in the transaxle was heated and the amount of heat radiation from the case surface was measured.
Technical Paper

The World's First Transverse 8-Speed Automatic Transmission

2013-04-08
2013-01-1274
We have developed the world's first 8-speed automatic transmission for transverse FWD/4WD vehicles. The aim of this new automatic transmission was to achieve world-class fuel economy while offering both smooth gear shift and sporty shift feeling suitable for luxury cars. This has been accomplished using wide spread gear ratio, outstanding low drag components and highly efficient hydraulic control system. In addition, we have achieved the compactness similar to current 6-speed automatic transmission by adopting new gear train and compact clutch layout. In this paper, the detail of this automatic transmission is introduced.
Technical Paper

Super Olefin Polymer for Material Consolidation of Automotive Interior Plastic Parts

1996-02-01
960296
A new automotive interior component material, TSOP-5 has been developed by refining the technology utilized to develop TSOP-1, the high modulus and high flow material for bumper covers. This new interior component material has excellent molding capability (MI=30dg/min.) yet still maintains high impact resistance which enables the material to be used in areas such as the dash board as well as trim covers requiring to meet the FMVSS 214, the new side impact regulation or the FMVSS 201, the new soft upper trim regulation.
Technical Paper

Study on Combustion Chamber Deposit Formation Mechanism -Influence of Fuel Components and Gasoline Detergents-

1997-05-01
971722
The combustion chamber deposit (CCD) forming tendency of gasoline components and detergents were investigated with laboratory tests ad engine dynamometer tests. In the dynamometer tests, the driving conditions under which fuels and detergents influence CCD formation were specified, and the effects of different gasoline components and detergent blends on CCD formation were examined. In the laboratory tests, the CCD forming process was investigated thoroughly [10]. The CCD forming tendency of aromatic compounds in gasoline were dependent not only on physical properties such as molecular weight, but also chemical structure (number or position of the alkyl substituents of aromatic molecules). As for oxygenates, engine dynamometer tests with MTBE blended gasoline yielded less CCD than the test without MTBE. The CCD forming tendency of detergents correlated with the thermal decompositon tendency of the detergent package and the concentration of the main agents.
Technical Paper

Study of Fuel Flow Rate Change in Injector for Methanol Fueled S.I. Engine

1995-02-01
950071
The change of the fuel flow rate in an injector with mileage accumulation causes poor drivability and exhaust emission deterioration in Otto-type methanol fueled vehicles with a multi-point fuel injection system. This is one of the serious problems which needs to be solved for the practical use of methanol fueled vehicles. The investigation results reveal that the wear of contact surfaces between a valve needle and a valve body increases the resistance force for valve needle movement and causes the change of dynamic fuel flow rate in the injector. The effects of several countermeasures to solve this problem are evaluated.
Technical Paper

Study of Cooling Drag Reduction Method by Controlling Cooling Flow

2014-04-01
2014-01-0679
As the demand for improved fuel economy increases and new CO2 regulations have been issued, aerodynamic drag reduction has become more critical. One of the important factors to consider is cooling drag. One way to reduce cooling drag is to decrease the air flow volume through the front grille, but this has an undesirable impact on cooling performance as well as component heat load in the under-hood area. For this reason, cooling drag reduction methods while keeping reliability, cooling performance and component heat management were investigated in this study. At first, air flow volume reduction at high speed was studied, where aerodynamic drag has the greatest influence. For vehicles sold in the USA, cooling specification tends to be determined based on low speed, while towing or driving up mountain roads, and therefore, there may be extra cooling capacity under high speed conditions.
Technical Paper

Stability of a One Box Type Vehicle in a Cross-Wind-An Analysis of Transient Aerodynamic Forces and Moments

1988-10-01
881878
One-box type vehicles are especially liable to a loss of stability when entering a region of cross-wind. The reasons for this instability were investigated using scale models and by means of a mathematical simulation. Results indicated that yawing moment attains a peak at a precise position of the vehicle relative to the cross-wind. Visualization of the air flow and measurement of the pressure distributions established the cause of the phenomenon. Furthermore a study was conducted into the effects of body shape on stability and the efficacy of various modifications was assessed.
Technical Paper

Silicon Nitride Swirl Lower-Chamber for High Power Turbocharged Diesel Engines

1985-02-01
850523
This paper describes application of sintered silicon nitride to the swirl lower-chamber in order to improve performance of turbocharged diesel engines. Various stress analyses by finite element method and stress measurements have been applied to determine the design specifications for the component, which compromise brittleness of ceramic materials. Material development was conducted to evaluate strength, fracture toughness, and thermal properties for the sintered bodies. Ceramic injection molding has been employed to fabricate components with large quantities in the present work. Quality assurance for the components can be made by reliability evaluation methods as well as non-destructive and stress loading inspections. It is found that the engine performance with ceramic component has been increased in the power out put of 9PS as compared to that of conventional engines.
Technical Paper

Recycling Technology of Surface Material for Interior Trims

2000-03-06
2000-01-0741
Two-layered surface materials composed of a thermoplastic olefin elastomer (TPO) skin and a cross-linked polypropylene (PP)foam are increasingly replacing the conventional PVC skin/PVC foam for interior trims. In the past, recycled material obtained by melt-blending TPO skin and PP foam could not be re-used for TPO skin because of its appearance. A new recycling technology using the reaction biaxial extruder with a reaction agent can decompose the network structure of PP foam. As a result, PP foam is dispersed into TPO uniformly and the recycled material has properties and an appearance similar to virgin TPO. These new properties may allow the application of the recycled material as a surface material.
Technical Paper

Recent Developments in Vehicle Interior Noise Reduction

1982-02-01
820963
In order to reduce the interior noise of a vehicle with a four-cylinder engine, investigations were made using finite element and vector methods, acoustic intensity testing and holography technique. The investigation resulted in inclination of the engine mounting, design changes to the front suspension member, a shock absorber engine mounting, structural modifications to reduce body panel vibration and a new engine mounting to insulate high frequency engine vibration.
Technical Paper

Quantitative Analysis of the Relation between Flame Structure and Turbulence in HCCI Combustion by Two-Dimensional Temperature Measurement

2008-04-14
2008-01-0061
The structure of HCCI (homogeneous charge compression ignition) combustion flames was quantitatively analyzed by measuring the two-dimensional gas temperature distribution using phosphor thermometry. It was found from the relation between a turbulent Reynolds number and Karlovitz number that, when compared with the flame propagation in an S.I. engine, HCCI combustion has a wider flame structure with respect to the turbulence scale. As a result of our experimentation for the influence of low temperature reaction (LTR) using two types of fuel, it was also confirmed that different types of fuel produce different histories of flame kernel structure.
Technical Paper

Properties of Zn-Fe Alloy Electroplated Steel Sheets

1984-02-01
840214
We have taken notice of Zn-Fe alloy electroplating with an eye to developing new corrosion-resistant steel sheets for automotive use with both cosmetic corrosion resistance and perforating corrosion resistance, and as a result of investigations into its paintability and corrosion resistance over the whole range of its compositions, we have come to a conclusion that steel sheets with two-layer Zn-Fe alloy electroplating that consists of a thin upper layer with a 75 to 85% Fe content and a lower layer with a 10 to 20% Fe content is the best choice.
Technical Paper

Prediction of the Life of CVJ Boot in Design Stage and Establishment of an Optimal Design Method with FEA

1998-02-23
980847
In a stage of designing a CVJ boot, analytic conditions of FEA method are established so that values calculated with the FEA method coincide with the actually measured values. This has made it possible to predict the life of the boot under bench testing. Furthermore, the boot field life can also be predicted by the minor rule based on the joint-angle frequencies of a vehicle. As a result, it has become possible to determine an optimal configuration in the design stage and to decrease the number of test cycles, resulting in reduced development lead time.
Technical Paper

Prediction of the Airflow Through Automotive Radiators Using 3-Dimensional Analysis

1993-10-01
932889
Air flow around a car front end configuration and through the radiator and condenser was computed simultaneously. Although the engine compartment was simplified to reduce computational cost, comparison of experimental data with the analysis showed excellent prediction of the air flow through the radiator and condenser.
Technical Paper

Plasma Treatment for Painting of Polypropylene Bumper

1985-02-01
850320
The colour painting of polypropylene bumpers has required development of a new polypropylene surface treatment which provides improved adhesion of the paint film to polypropylene. According to the results of various improvement studies on the application of plasma treatment, it has been discovered that surface treatment by means of plasma of an oxygen and nitrogen gas mixture activated by microwave (2,450 MHz) provides a remarkable improvement in adhesion. Furthermore, establishing a technique to diffuse plasma effectively within the treatment chamber has enabled a uniform surface treatment of several polypropylene bumpers formed in large and complicated shapes.
Technical Paper

Nylon 6-Clay Hybrid - Synthesis, Properties and Application to Automotive Timing Belt Cover

1991-02-01
910584
ϵ-caprolactam was polymerized in the interlayer space of montmorillonite, the clay mineral yielding a nylon-clay hybrid (NCH). X-ray and TEM measurements revealed that each template of the silicate, which was 1 nm thick, was dispersed in the nylon 6 matrix, and that the interlayer distance of clay increased continuously from 1.2 nm for the unintercalated material to 21.4 nm for the intercalated material. Thus, NCH is a polymer-based molecular composite or a nano-composite. NCH contains 1-15 vol% of monolayer clay. Injection-molded NCH showed excellent mechanical properties compared with nylon 6 in terms of tensile strength, tensile modulus and heat resistance. The tensile modulus of NCH was twice that of Nylon 6, and the heat distortion temperature increased from 65°C for nylon 6 to 145°C for the NCH containing only 1.6 vol% of a clay mineral. It was found that such excellent properties of an NCH system was due to the strong ionic interaction between nylon 6 and the silicate layer.
X