Search Results

Combustion visualizations were carried out in a constant volume vessel to study the partially premixed combustion of a gasoline-like fuel using high speed imaging. The test fuel (G80H20) is composed by volume 80% commercial gasoline and 20% n-heptane. The effects of ambient gas composition, ambient temperature and injection pressure on G80H20 combustion characteristics were analyzed. Meanwhile, a comparison of the EGR effect on combustion process between G80H20 and diesel was made. Four ambient gas conditions that represent the in-cylinder gas compositions of a heavy-duty diesel engine with EGR ratios of 0%, 20%, 40% and 60% were used to simulate EGR conditions. Variables also include two ambient temperature (910K and 870K) and two injection pressure (20 MPa and 50 MPa) conditions.

Atomization of fuel sprays is a key factor in controlling the combustion quality in the direct-injection engines. In this present work, the effect of saturation ratio (Rs) on the near nozzle spray patterns of ethanol was investigated using an ultra-high speed imaging technique. The Rs range covered both flash-boiling and non-flash boiling regions. Ethanol was injected from a single-hole injector into an optically accessible constant volume chamber at a fixed injection pressure of 40 MPa with different fuel temperatures and back pressures. High-speed imaging was performed using an ultrahigh speed camera (1 million fps) coupled with a long-distance microscope. Under non-flash boiling conditions, the effect of Rs on fuel development was small but observable. Clear fuel collision can be observed at Rs=1.5 and 1.0. Under the flash boiling conditions, near-nozzle spray patterns were significant different from the non-flash boiling ones.

Ground impact caused by road debris can result in very severe fire accident of Electric Vehicles (EV). In order to study the ground impact accidents, a Finite Element model of the battery pack structure is carefully set up according to the practical designs of EVs. Based on this model, the sequence of the deformation process is studied, and the contribution of each component is clarified. Subsequently, four designs, including three enhanced shield plates and one enhanced housing box, are investigated. Results show that the BRAS (Blast Resistant Adaptive Sandwich) shield plate is the most effective structure to decrease the deformation of the battery cells. Compared with the baseline case, which adopts a 6.35-mm-thick aluminum sheet as the shield plate, the BRAS can reduce the shortening of cells by more than 50%. Another type of sandwich structure, the NavTruss, can also improve the safety of battery pack, but not as effectively as the BRAS.

Engine torque fluctuation is a great threat to vehicle comfort and durability. Former researches tried to solve this problem by introducing active damping system, which means the motor is controlled to produce torque ripple with just the opposite phase to that of the engine. By this means, the torque fluctuation produced by the motor and the engine can be reduced. In this paper, a new method is raised. An attempt is proposed by changing the traditional structure of the motor, making it produce ripple torque by itself instead of controlling the motor. In this way a special used ISG (Integrated Starter Generator) motor for HEV (Hybrid Electrical Vehicles) is made to achieve active damping. In order to study the possibility, a simulation, which focus on the motor instead of the whole system, is developed and series-parallel configuration is used in this simulation. As for the motor that used in this paper, four kinds of motors have been investigated and compared.

The mechanical behavior of polyvinyl butyral (PVB) film plays an important role in windshield crashworthiness and pedestrian protection and should be depth study. In this article, the uniaxial tension tests of PVB film at various strain rates (0.001 s-1, 0.01 s-1, 0.1 s-1, 1 s-1) and temperatures (-10°C, 0°C, 10°C, 23°C, 40°C, 55°C, 70°C) are conducted to investigate its mechanical behavior. Then, temperature and strain rate dependent viscoelastic characteristics of PVB are systematically studied. The results show that PVB is a kind of temperature and strain rate sensitive thermal viscoelastic material. Temperature increase and strain rate decrease have the same influence on mechanical properties of PVB. Besides, the mechanical characteristics of PVB change non-linearly with temperature and strain rate. Finally, two thermal viscoelastic constitutive model (ZWT model and DSGZ model) are suggested to describe the tension behavior of PVB film at various strain rates and temperatures.

A conceptual approach to help understand and simulate droplet induced pre-ignition is presented. The complex phenomenon of oil-fuel droplet induced pre-ignition has been decomposed to its elementary processes. This approach helps identify the key fluid properties and engine parameters that affect the pre-ignition phenomenon, and could be used to control LSPI. Based on the conceptual model, a 3D CFD engine simulation has been developed which is able to realistically model all of the elementary processes involved in droplet induced pre-ignition. The simulation was successfully able to predict droplet induced pre-ignition at conditions where the phenomenon has been experimentally observed. The simulation has been able to help explain the observation of pre-ignition advancement relative to injection timing as experimentally observed in a previous study [6].

Electric vehicle (EV) is a worldwide researching focus due to its environmental friendliness, but the inaccurate Remaining Driving Range (RDR) estimation hinders the EVs' popularity, and an accurate determination of the battery Residual Usable Energy (RUE) is the key factor to obtain a precise RDR value. A common RUE estimation method is based on State-of-Charge (SOC) estimation, in which the RUE is proportionally related to the current SOC. However, the battery voltage varies significantly under real-world conditions, and the traditional method results in certain estimation errors. An adaptive RUE prediction method (AEP) is introduced in this paper, in which the dynamic voltage is predicted based on the future discharge profile and a battery model, while the RUE is then calculated by the predicted voltage and current sequences.

Ammonia shows promise as an alternative fuel for internal combustion engines (ICEs) in reducing CO2 emissions due to its carbon-free nature and well-established infrastructure. However, certain drawbacks, such as the high ignition energy, the narrow flammability range, and the extremely low laminar flame speed, limit its widespread application. The dual fuel (DF) mode is an appealing approach to enhance ammonia combustion. The combustion characteristics of ammonia-diesel dual fuel mode and ammonia-PODE3 dual fuel mode were experimentally studied using a full-view optical engine and the high-speed photography method. The ammonia energy ratio (ERa) was varied from 40% to 60%, and the main injection energy ratio (ERInj1) and the main injection time (SOI1) were also varied in ammonia-PODE3 mode.

A hydraulic chamber is embedded in serial with the accumulator of a normal mono-tube magnetorheological fluid damper (MRFD). The damper stiffness can be adjusted by changing the accumulator volume with the hydraulic chamber. The hydraulic chamber is connected to an electric pump and controlled by the braking-by-wire (BBW) system. A modified bi-viscosity magnetorheological fluid (MRF) model that explicitly includes the parameter of control current is proposed. A dynamic model of this hydraulic MRFD is subsequently set up based on the MRF model. Experiments are conducted to validate the model and simulations are carried out to study the influences of accumulator volume on the external performances. Results show that the hydraulic chamber is able to provide rapid variations of the external force through accumulator volume changes.

Polyvinyl Butyral (PVB) laminated glass has been widely used in automotive industry as windshield material. Cracks on the PVB laminated glass contain large amount of impact information, which can contribute to accident reconstruction investigation. In this study, the impact-induced in-plane dynamic cracking of the PVB laminated glass is investigated. Firstly, a drop-weight combined with high-speed photography experiment device is set up to investigate the radial cracks propagation on the PVB laminated glass sheet. Both the morphology and the velocity time history curve of the radial cracks are recorded and analyzed to investigate the basic mechanism of the crack propagation process. Afterwards, a three-dimensional laminated plate finite element (FE) model is set up and dynamic cracking process is simulated based on the extended finite element method (XFEM).

As mechanical damage induced thermal runaway of lithium-ion batteries has become one of the research hotspots, it is quite crucial to understand the mechanical behavior of component materials of lithium battery. This study focuses on the mechanical performance of separators and electrodes under different loading conditions and the error sources analysis for test results. Uniaxial tensile tests were conducted under both quasi-static and dynamic loading conditions. The strain was acquired through the combination of high speed camera and digital image correlation (DIC) method while the force was obtained with a customized load cell. Noticeable anisotropy and strain rate effect were observed for separators. The fracture mode of separators is highly correlated to the microscopic fiber orientation. To demonstrate the correlation microscopic images of separator material were obtained through SEM to match the facture edges of tensile tests at different loading directions.

Highly autonomous vehicles have drawn the interests of many researchers in recent years. For highly autonomous vehicles, a high-definition (HD) map is crucial since it provides accurate information for autonomous driving. However, due to the possible fast-changing environment, the performance of HD maps will deteriorate over time if timely updates are not ensured. Therefore, this paper studies the updating of lightweight HD maps in closed areas. Firstly, a novel two-layer map model called a lightweight HD map is introduced to support autonomous driving in a flexible and efficient way. Secondly, typical updating of scenarios in closed areas with non-paved roads is abstracted into operations including area border expansion, road addition, and road deletion. Meanwhile, a map updating framework is proposed to address the issue of map updating in closed areas. Finally, an experiment is conducted to demonstrate the feasibility and effectiveness of the proposed map updating approach.

Detailed chemical kinetics is essential for accurate prediction of combustion performance as well as emissions in practical combustion engines. However, implementation of that is challenging. In this work, dynamic adaptive chemistry (DAC) is integrated into large eddy simulations (LES) of an n-heptane spray flame in a constant volume chamber (CVC) with realistic application conditions. DAC accelerates the time integration of the governing ordinary differential equations (ODEs) for chemical kinetics through the use of locally (spatially and temporally) valid skeletal mechanisms. Instantaneous flame structures and global combustion characteristics such as ignition delay time, flame lift-off length (LOL) and emissions are investigated to assess the effect of DAC on LES-DAC results. The study reveals that in LES-DAC simulations, the auto-ignition time and LOL obtain a well agreement with experiment data under different oxygen concentrations.

Gasoline Compression Ignition has been widely studied in recent years. The in-cylinder stratified charge in gasoline Partially Premixed Compression Ignition (PPCI) can extend the high load range with lower pressure rise rate than Homogeneous Charge Compression Ignition (HCCI). However, it is still not clear that whether there is flame propagation in the gasoline compression igntion mode and how the flame propagation influences the combustion process and pollution formation. In order to investigate the effect of flame, several gasoline compression ignition cases, including the single-stage and two-stage heat release processes, are simulated with the KIVA-3V Release 2 code in this study. The G-equation is employed to account for flame propagation, and the reduced i-octane/n-heptane mechanism is used to handle the chemical reactions. The results show that the flame propagation exists in the combustion process and it can accelerate the heat release slightly.

Hydraulically damped rubber mount (HDM) can effectively attenuate vibrations transmitting between automotive powertrain and body/chassis, and reduce interior noise of car compartment. This paper involves an analytical qualitative analysis approach of dynamics characteristics of HDM. Analysis of experimental results verifies the effectiveness of the qualitative analysis approach. Frequency- and amplitude-dependent dynamic characteristic of HDM are investigated to clarify working mechanism of HDM. The presented qualitative analysis approach provides a convenient performance adjustment guideline of HDM to meet vibration isolation requirements of powertrain mount system.

In this decade, the detailed multi-layer FE model is always applied for investigating the mechanical behavior of Li-ion batteries under mechanical abuse. However, establishing a detailed model of different types of batteries requires a series of material characterization of components. To improve the efficiency of the procedure of component calibration, we introduce a procedure of automatic coating material characterization as an example to represent the strategy. The proposed method is constructing a response solver through MATLAB to predict the mechanical behavior of the coating specimen's representative volume element (RVE) under designated test conditions. The coating material is represented through Drucker-Prager-Cap (DPC) model. All parameters, including boundary conditions and material parameters, are included in this solver.

This article is concerned with identification of true stress-strain curve under biaxial tension of thermoplastic polymers. A new type of biaxial tension attachment was embedded first in a universal material test machine, which is able to transform unidirectional loading of the test machine to biaxial loading on the specimen with constant velocity. Cruciform specimen geometry was optimized via FE modeling. Three methods of calculating true stress in biaxial tension tests were compared, based on incompressibility assumption, linear elastic theory and inverse engineering method, respectively. The inverse engineering method is more appropriate for thermoplastic polymers since it considers the practical volume change of the material during biaxial tension deformation. The strategy of data processing was established to obtain biaxial tension true stress-strain curves of different thermoplastic polymers.

The driving power system can be combined with lasers, lights, etc., and applied to automobiles to achieve various functions. Under the general trend of the development of intelligent vehicles, people have higher and higher requirements for the accuracy and power of various equipment. However, as power increases, how to ensure the stability of factors such as current is a challenging problem. Therefore, it is extremely important to study and design a high-power drive system in this paper, so as to ensure a stable output of the current. The system is composed of power supply, load, secondary power supply and control chip. The choice of power supply and load is conventional model. The secondary power supply adopts step-down circuit, with synchronous rectifier chip, which can effectively reduce energy consumption, and with temperature protection device, which can ensure the safe and reliable operation of equipment.

Dieseline combustion as a concept combines the advantages of gasoline and diesel by offline or online blending the two fuels. Dieseline has become an attractive new compression ignition combustion concept in recent years and furthermore an approach to a full-boiling-range fuel. High speed imaging with near-parallel backlit light was used to investigate the spray characteristics of dieseline and pure fuels with a common rail diesel injection system in a constant volume vessel. The results were acquired at different blend ratios, and at different temperatures and back pressures at an injection pressure of 100MPa. The penetrations and the evaporation states were compared with those of gasoline and diesel. The spray profile was analyzed in both area and shape with statistical methods. The effect of gasoline percentage on the evaporation in the fuel spray was evaluated.

The windshield is one of the most critical vehicle components in terms of pedestrian safety; however, it has not been thoroughly and systematically investigated through combined experimental and theoretical analysis. Firstly, this paper carries out quasi-static experiments on Material Testing System (MTS) and dynamic experiments on Split Hopkinson Pressure Bar (SHPB) and new tests data are obtained. Results indicate that Polyvinyl butyral (PVB)-laminated glass behaves nonlinearly and rate-dependently under various strain rates, from 1x10-⁵s-₁~6x10₃ s-₁. Thus, a constitutive model covering all strain rates is proposed to describe the constitutive behavior of PVB-laminated glass and it fits well with the experimental data. Further, the constitutive relation is embedded into the 3D finite element model of windshield. With the definition of four governing factors and two evaluation indicators, the head protection characteristics of windshield are numerically studied.