Search Results

Combustion visualizations were carried out in a constant volume vessel to study the partially premixed combustion of a gasoline-like fuel using high speed imaging. The test fuel (G80H20) is composed by volume 80% commercial gasoline and 20% n-heptane. The effects of ambient gas composition, ambient temperature and injection pressure on G80H20 combustion characteristics were analyzed. Meanwhile, a comparison of the EGR effect on combustion process between G80H20 and diesel was made. Four ambient gas conditions that represent the in-cylinder gas compositions of a heavy-duty diesel engine with EGR ratios of 0%, 20%, 40% and 60% were used to simulate EGR conditions. Variables also include two ambient temperature (910K and 870K) and two injection pressure (20 MPa and 50 MPa) conditions.

This paper presents a two-layer torque vectoring control strategy for the Formula SAE racing car of Tsinghua University to enhance steering response, lateral stability and track performance. Firstly, the dynamic model of the existing FSAE car is built as parameters of tires, suspensions, motors and aerodynamics are measured and identified. Secondly, this paper develops a two-layer torque vectoring strategy, the upper-layer direct yaw moment (DYC) controller and the lower-layer torque distribution controller are developed in Simulink. The upper-layer sliding mode control DYC controller calculates the target additional yaw moment according to the target yaw rate based on the two-degree-of-freedom (2DOF) reference model, and the sideslip angle is constrained as well.

Gasoline Direct Injection (GDI) engines have developed rapidly in recent years driven by fuel efficiency and consumption requirements, but face challenges such as injector deposits and particulate emissions compared to Port Fuel Injection (PFI) engines. While the mechanisms of GDI injector deposits formation and that of particulate emissions have been respectively revealed well, the impact of GDI injector deposits and their relation to particulate emissions have not yet been understood very well through systematic approach to investigate vehicle emissions together with injector spray analysis. In this paper, an experimental study was conducted on a GDI vehicle produced by a Chinese Original Equipment Manufacturer (OEM) and an optical spray test bench to determine the impact of injector deposits on spray and particulate emissions.

Atomization of fuel sprays is a key factor in controlling the combustion quality in the direct-injection engines. In this present work, the effect of saturation ratio (Rs) on the near nozzle spray patterns of ethanol was investigated using an ultra-high speed imaging technique. The Rs range covered both flash-boiling and non-flash boiling regions. Ethanol was injected from a single-hole injector into an optically accessible constant volume chamber at a fixed injection pressure of 40 MPa with different fuel temperatures and back pressures. High-speed imaging was performed using an ultrahigh speed camera (1 million fps) coupled with a long-distance microscope. Under non-flash boiling conditions, the effect of Rs on fuel development was small but observable. Clear fuel collision can be observed at Rs=1.5 and 1.0. Under the flash boiling conditions, near-nozzle spray patterns were significant different from the non-flash boiling ones.

The accuracy of road input identifiaction for autonomous vehicles (AVs) system, especially in state-based AVs control for improving road handling and ride comfort, is a challenging task for the intelligent transport system. Due to the high fatality rate caused by inaccurate state-based control algorithm, how to precisely and effectively acquire road rough information and chose the reasonable road-based control algorithm become a hot topic in both academia and industry. Uncertainty is unavoidable for AVs system, e.g., varying center of gravity (C.G.) of sprung mass, controllable suspension damping force or variable spring stiffness. To tackle the above mentioned, this paper develops a novel observer approach, which combines unscented Kalman filter (UKF) and Minimum Model Error (MME) theory, to optimize the estimation accuracy of the road rough for AVs system. A full-car nonlinear model and road profile model are first established.

A conceptual approach to help understand and simulate droplet induced pre-ignition is presented. The complex phenomenon of oil-fuel droplet induced pre-ignition has been decomposed to its elementary processes. This approach helps identify the key fluid properties and engine parameters that affect the pre-ignition phenomenon, and could be used to control LSPI. Based on the conceptual model, a 3D CFD engine simulation has been developed which is able to realistically model all of the elementary processes involved in droplet induced pre-ignition. The simulation was successfully able to predict droplet induced pre-ignition at conditions where the phenomenon has been experimentally observed. The simulation has been able to help explain the observation of pre-ignition advancement relative to injection timing as experimentally observed in a previous study [6].

A conventional vehicle with gasoline engine was tested on a chassis dynamometer over the new European drive-cycle (NEDC). The distributions of the engine speed and power, the throttle positions during the drive cycle are analyzed. Engine idling, acceleration and deceleration take an important proportion in the drive cycle. If engine idling is instead by engine stop, the fuel consumption will be improved by 2.27%. In an Integrated Starter Generator (ISG) system, with the assist of the starter/generator, transient operation of the engine will decrease, which reduces fuel consumption by 6%. Fuel economy will be also improved by braking regeneration and restricting operating points to an optimized region, the details are not discussed in this paper. To reduce fuel consumption further, the region where engine usually runs in urban traffic, should be paid more attention to while engine calibration.

Ammonia shows promise as an alternative fuel for internal combustion engines (ICEs) in reducing CO2 emissions due to its carbon-free nature and well-established infrastructure. However, certain drawbacks, such as the high ignition energy, the narrow flammability range, and the extremely low laminar flame speed, limit its widespread application. The dual fuel (DF) mode is an appealing approach to enhance ammonia combustion. The combustion characteristics of ammonia-diesel dual fuel mode and ammonia-PODE3 dual fuel mode were experimentally studied using a full-view optical engine and the high-speed photography method. The ammonia energy ratio (ERa) was varied from 40% to 60%, and the main injection energy ratio (ERInj1) and the main injection time (SOI1) were also varied in ammonia-PODE3 mode.

Multibody human models are widely used to investigate responses of human during an automotive crash. This study aimed to validate a commercially available multibody human body model against response corridors from volunteer tests conducted by Naval BioDynamics Laboratory (NBDL). The neck model consisted of seven vertebral bodies, and two adjacent bodies were connected by three orthogonal linear springs and dampers and three orthogonal rotational springs and dampers. The stiffness and damping characteristics were scaled up or down to improve the biofidelity of the neck model against NBDL volunteer test data because those characteristics were encrypted due to confidentiality. First, sensitivity analysis was performed to find influential scaling factors among the entire set using a design of experiment.

In a monotube magnetorheological fluid damper (MRFD), there usually exists a compensation chamber with designated initial gas pressure. This enclosed compensation chamber works as an air spring to some degree to provide force to the working piston. In this work, in order to extend the external damping force range and improve the controlling efficiency, a structure of MRFD with three additional accumulators is proposed. These additional accumulators are connected to the atmosphere through an air pump and the compensation chamber with a barometric valve. The external damping force range thus can be rapidly adjusted through mode shifting with this configuration. A mathematical model of this damper with coupled effects between the air and the magnetorheological fluid (MRF) is developed. Comparing the bench tests results with some simulation outcomes, the simulation model of this MRFD is validated.

The desired yaw rate is a vital target parameter for vehicle stability control, which is currently determined as a steady-state yaw rate by the linear single-track vehicle model. Tire nonlinearity deteriorates the effect of vehicle stability control at larger lateral acceleration. This paper proposes a new calculation method of the steady-state yaw rate considering the tire nonlinearity based on the brush tire model. To validate and verify the proposed method, step steering tests of the target vehicle under different lateral accelerations are carried out on a real proving ground. The results show that when the lateral acceleration is relatively small, the difference between the calculation results of the proposed method and the traditional one is not apparent, and both methods can provide a good estimation for the steady-state yaw rate; however, when the lateral acceleration is relatively large, the difference becomes apparent.

Highly autonomous vehicles have drawn the interests of many researchers in recent years. For highly autonomous vehicles, a high-definition (HD) map is crucial since it provides accurate information for autonomous driving. However, due to the possible fast-changing environment, the performance of HD maps will deteriorate over time if timely updates are not ensured. Therefore, this paper studies the updating of lightweight HD maps in closed areas. Firstly, a novel two-layer map model called a lightweight HD map is introduced to support autonomous driving in a flexible and efficient way. Secondly, typical updating of scenarios in closed areas with non-paved roads is abstracted into operations including area border expansion, road addition, and road deletion. Meanwhile, a map updating framework is proposed to address the issue of map updating in closed areas. Finally, an experiment is conducted to demonstrate the feasibility and effectiveness of the proposed map updating approach.

In this work, large eddy simulation (LES) with a K-equation subgrid turbulent kinetic energy model is implemented into the CFD code KIVA3V to study the features of liquid fuel spray and combustion using gradually varying grid in a constant volume chamber. The characteristic time-scale combustion model (CTC) incorporating a turbulent timescale is adopted to predict the combustion process and the SHELL auto-ignition model is used to predict auto-ignition. Combustion is also simulated using Parallel Detailed Chemistry with Lu's n-heptane reduced mechanism (58 species), which has been added into the KIVA3V-LES code. The computational results are compared with Sandia experimental data for non-reacting and reacting cases. As a result, LES can capture the complex structure of the spray and temperature distribution as well as the trend of ignition delay and flame lift-off length variations. Better results are obtained using the Parallel Detailed Chemistry than the CTC model.

A three-dimensional numerical investigation into aerodynamic feature of the turbocharger turbine under pulsating flow conditions is conducted in this paper. Dual time stepping approach is applied to solve the unsteady Navier-Stokes equations, while the Jameson central scheme is brought in for spatial discretization, and Spalart-Allmaras turbulence model is employed in order to get good viscous resolution, accuracy and computing efficiency. The quasi-steady and unsteady performance of the turbine is given and compared. Five blade passage cross sections are chosen to analyze the structure of the secondary flow at 4 key instants. The developments of different vortex, especially the tip leakage vortex, passage vortex are discussed. The results have shown that the unsteady performance deviates substantially from quasi-steady performance, and the secondary flow structure varies tremendously under the pulsating flow conditions.

Hydraulically damped rubber mount (HDM) can effectively attenuate vibrations transmitting between automotive powertrain and body/chassis, and reduce interior noise of car compartment. This paper involves an analytical qualitative analysis approach of dynamics characteristics of HDM. Analysis of experimental results verifies the effectiveness of the qualitative analysis approach. Frequency- and amplitude-dependent dynamic characteristic of HDM are investigated to clarify working mechanism of HDM. The presented qualitative analysis approach provides a convenient performance adjustment guideline of HDM to meet vibration isolation requirements of powertrain mount system.

Injection rate control is considered as an effective way to optimize diesel combustion process, decrease emission and improve fuel economy. There are many injection rate shaping devices, but most of them still suffer from structure complexity and parameter sensitivity which limit their effectiveness and practicality. A new initial injection rate control method in solenoid-controlled diesel injection systems is introduced in this paper. The basic idea of this method is to maintain a small spill passage between plunger chamber and inlet port during initial injection period. The initial injection rate can be regulated by changing the closing timing of the solenoid-controlled spill valve. This method has the advantages of simple construction, flexible adjustment and stable performance. Computer aided analysis and design based on a simulation program of the system is conducted to compare and select the sizes of the small spill passage according to their effect on injection characteristics.

A hybrid unstructured Navier-Stokes method is presented for the simulation of the incompressible turbulent flows around vehicle bodies. The hybrid grid system is composed of a structured or semistructured grid for the near-wall viscous region, and an unstructured grid for the remainder of the computational domain. By using prismatic cells, the number of cells in the boundary-layer region becomes approximately one-third of the tetrahedral grid. And the laminated grid rather than the tetrahedral grid is more suitable in the boundary-layer region for accurately computing the viscous terms. The incompressible Navier-Stokes equations are solved on the hybrid grid by a cell-vertex, central differencing finite volume method. The numerical accuracy of the present method is discussed by comparing with the experimental data for the cases of flows around a car model at different ground clearances.

Compressed Natural Gas (CNG), because of its low cost, high H/C ratio, and high octane number, has great potential in automotive industry, especially for heavy-duty commercial vehicles. However, relative slow flame speed of natural gas leads to long combustion duration and low thermal efficiency and tends to cause knock combustion at high load, which will aggravate engine thermal load and reliability. Enhancing turbulence intensity in combustion chamber is an effective way to accelerate flame propagation speed and improve combustion performance. In this study, the flow simulations of several piston bowls with different inner-convex forms were carried out using three-dimensional computational fluid dynamics (3D-CFD) software CONVERGE. The numerical results showed the piston bowls with inner-convex could disturb the charge swirl motion and enhance turbulence of different intensity. A hexagram geometry bowl was proved to have the best function in strengthening turbulence intensity.

This article is concerned with identification of true stress-strain curve under biaxial tension of thermoplastic polymers. A new type of biaxial tension attachment was embedded first in a universal material test machine, which is able to transform unidirectional loading of the test machine to biaxial loading on the specimen with constant velocity. Cruciform specimen geometry was optimized via FE modeling. Three methods of calculating true stress in biaxial tension tests were compared, based on incompressibility assumption, linear elastic theory and inverse engineering method, respectively. The inverse engineering method is more appropriate for thermoplastic polymers since it considers the practical volume change of the material during biaxial tension deformation. The strategy of data processing was established to obtain biaxial tension true stress-strain curves of different thermoplastic polymers.

The driving power system can be combined with lasers, lights, etc., and applied to automobiles to achieve various functions. Under the general trend of the development of intelligent vehicles, people have higher and higher requirements for the accuracy and power of various equipment. However, as power increases, how to ensure the stability of factors such as current is a challenging problem. Therefore, it is extremely important to study and design a high-power drive system in this paper, so as to ensure a stable output of the current. The system is composed of power supply, load, secondary power supply and control chip. The choice of power supply and load is conventional model. The secondary power supply adopts step-down circuit, with synchronous rectifier chip, which can effectively reduce energy consumption, and with temperature protection device, which can ensure the safe and reliable operation of equipment.