Search Results

The US Army uses a light tactical High-Mobility Multi-Purpose Wheeled Vehicle (HMMWV) which, due to the amount of armor added, requires air conditioning to keep its occupants comfortable. The current system uses R134a in a dual evaporator, remote-mounted condenser, engine-driven compressor system. This vehicle has been adapted to use an environmentally friendly refrigerant (carbon dioxide) to provide performance, efficiency, comfort and logistical benefits to the Army. The unusual thermal heat management issues and the fact that the vehicle is required to operate under extreme ambient conditions have made the project extremely challenging. This paper is a continuation of work presented at the SAE Alternate Refrigerants Symposium held in Phoenix last June [1].

Using a three-degree-of-freedom vehicle model (side-slip, yaw and roll degrees of freedom) and a nonlinear, saturating rire model, the behavior of a typical exemplar vehicle (1986 Dodge Lancer Turbo) was simulated. Steady state performance was examined through simulating a skidpad lateral accelerarion maneuver. A lane change maneuver was used to reprcsenr transient performance characteristics. A few simple experiments were conducted wirh rhe exemplar vehicle to establish parameters and verify some performance properties. Results of both steady srare and rransienr simulations showed that four -wheel steer offers lirrle or no demonstrated performance advanrages over two-wheel steer.

Wind tunnel tests were performed on an 8.9-percent scale semispan wing in the Wichita State University 7x10-foot wind tunnel with simulated ice accretion shapes. Simulated ice shapes from large-droplet clouds, simple-geometry ice horn shapes, and simple-geometry spanwise ridge shapes typical of runback icing were tested. Three Reynolds number and Mach number combinations were tested over a range of angles of attack. Aerodynamic forces and moments were acquired from the tunnel balance and surface pressures and oil flow visualizations were acquired. This research supplements the Swept Wing Icing Program recently concluded by NASA, FAA, ONERA, and their partners by testing new ice shapes on the same wind tunnel model. Additional surface roughness was added to simulate large-droplet ice accretion aft of the highly three-dimensional primary ice shape, and it had little effect on the wing aerodynamic performance.

The type of differential used in a vehicle has an important and often-neglected effect on handling performance. This is particularly important in racing applications, such as in IndyCar racing, in which the type of differential chosen depends on the course being raced (superspeedway ovals, short ovals, temporary street courses and permanent road courses). In the present work, we examine the effect of a locked rear differential on oversteer/understeer behavior. Using a linear tire model, it is shown that employing a locked differential adds a constant understeer offset to the steering wheel angle (SWA) -v- lateral acceleration vehicle signature. A computer simulation of steady-state cornering behavior showed that the actual effect is much more complicated, and is strongly influenced by static weight distribution, front/rear roll couple distribution, available traction and the radius of the turn being negotiated.

An experimental study was performed at the University of Illinois at Urbana-Champaign Low-Speed Wind Tunnel to quantify the performance and flowfield effects of two-element open-wheel-race-car front wing configurations. Four distinct configurations were tested in- and out-of-ground effect and at various speeds (Reynolds numbers), angles of attack, and flap positions. A splitter plate was installed in the wind tunnel to act as the ground plane. Data presented include balance force measurements, surface pressure data, and downstream flow measurements using a seven-hole probe. Results show that these elementary factors in the design of race-car front wings have a significant effect on wing performance and behavior of the downstream flowfield.

The transporting of live cattle involves the use of Class 8 tractors and livestock semi-trailers for transportation from farms and feedlots to processing plants. This travel may include unimproved roads, local streets, two lane highways, as well as interstate highways. Typically, cattle are compartmentalized in a “double deck” fashion as it provides utility and comports with size and weight limits for commercial Class 8 vehicles. Concern has been expressed for the effect of cattle movement upon the dynamic performance of the loaded Class 8 tractor-livestock trailer assembly. Loading guidelines exist for cattle that attempt to prevent injury or debilitation during transit, and literature exists on the orientation and some kinematics of loaded cattle. Considerable literature exists on the effect of liquid slosh in tankers and swinging beef carcasses suspended from hooks in refrigerated van trailers on the dynamic response and roll stability of those vehicles.

The ability to categorize, compare and segregate the roll dynamical behavior of various vehicles from one another is a subject of considerable research interest. A number of comparison paradigms have been developed (static stability index, roll couple methods, etc.), but all suffer from lack of robustness: results developed on the basis of a particular comparison metric are often not able to be generalized across vehicle lines and types, etc., or they simply do not segregate vehicles at all. In addition, most models do not describe vehicle dynamics in sufficient detail, and some contain no dynamics at all (e.g., static stability index = t/2h). In the present work, static stability index, a two-degree-of-freedom roll model and a three-degree-of-freedom roll and handling model were used to locate eigenvalues for a sample of 43 vehicles consisting of (1) passenger cars, (2) light trucks, (3) sport/utility vehicles and (4) minivans.

Cavitation plays a significant role in the spray characteristics and the subsequent mixing and combustion process in engines. Cavitation has beneficial effects on the development of the fuel sprays by improving injection velocity and promoting primary break-up. On the other hand, intense pressure peaks induced by the vapor collapse may lead to erosion damage and severe degradation of the injector performance. In the present paper, the transient cavitating flow in the injector-like geometry was investigated using the modified turbulence model and cavitation criterion. A local density correction was used in the Reynolds-averaged Navier-Stokes turbulence model to reduce the turbulent viscosity, which facilitates the cavitation development. The turbulent stress was also considered in the cavitation inception stage. The modified model is capable of reproducing the cavitating flow with an affordable computational cost.

ROPS-TEST is a newly developed, interactive, graphics program that may be used to simulate testing of roll bars. Cross-sections that it currently supports include solid rectangular, rectangular tubing, and circular tubing. ROPS-TEST can be used to simulate testing for crush, rear and side loading. Output from ROPS-TEST includes load-deflection and strain energy-deflection plots. ROPS-TEST does not replace actual testing of prototype roll bars. Rather it serves as a design tool to select the best design options for a particular application prior to actual testing of the prototype roll bars.

Roll bars are currently a primary source of operator protection for recreational vehicles, for certain lawn and garden tractors and for small agricultural tractors. In this paper we describe a family of nonlinear models to predict the large deflection response of a roll bar due to yielding of the material. This yielding permits the structure to absorb energy. The stress-strain relationship employs a power law model. Subsequent calculation of the complementary energy stored in the structure and application of Castigliano's second theorem yield the deflection at the point of loading. To demonstrate the feasibility of this energy method in the simulation of testing of roll bars, we present numerical results for the side, vertical, and fore-aft loading cases. Results include the load-deflection response for each load case as well as the strain energy stored in the roll bar as it deforms.