Search Results

The Energy Finite Element Analysis(EFEA) is a recent development for high frequency vibro-acoustic analysis, and constitutes an evolution in the area of high frequency computations. The EFEA is a wave based approach, while the SEA is a modal based approach. In this paper the similarities in the theoretical development of the two methods are outlined. The main scope of this paper is to establish the validity of the EFEA by analyzing several complex structural-acoustic systems. The EFEA solutions are compared successfully to SEA results and to solutions obtained from extremely dense conventional FEA models.

An experimental study is performed for homogeneous charge compression ignition (HCCI) combustion focusing on late phasing conditions with high cyclic variability (CV) approaching misfire. High CV limits the feasible operating range and the objective is to understand and quantify the dominating effects of the CV in order to enable controls for widening the operating range of HCCI. A combustion analysis method is developed for explaining the dynamic coupling in sequences of combustion cycles where important variables are residual gas temperature, combustion efficiency, heat release during re-compression, and unburned fuel mass. The results show that the unburned fuel mass carries over to the re-compression and to the next cycle creating a coupling between cycles, in addition to the well known temperature coupling, that is essential for understanding and predicting the HCCI behavior at lean conditions with high CV.

Digital human models (DHM) are now widely used to assess worker tasks as part of manufacturing simulation. With current DHM software, the simulation engineer or ergonomist usually makes a manual estimate of the likely worker standing location with respect to the work task. In a small number of cases, the worker standing location is determined through physical testing with one or a few workers. Motion capture technology is sometimes used to aid in quantitative analysis of the resulting posture. Previous research has demonstrated the sensitivity of work task assessment using DHM to the accuracy of the posture prediction. This paper expands on that work by demonstrating the need for a method and model to accurately predict worker standing location. The effect of standing location on work task posture and the resulting assessment is documented through three case studies using the Siemens Jack DHM software.

In-cylinder fluid velocity is measured in an optically accessible, fired HSDI engine at idle. The velocity field is also calculated, including the full induction stroke, using multi-dimensional fluid dynamics and combustion simulation models. A detailed comparison between the measured and calculated velocities is performed to validate the computed results and to gain a physical understanding of the flow evolution. Motored measurements are also presented, to clarify the effects of the fuel injection process and combustion on the velocity field evolution. The calculated mean in-cylinder angular momentum (swirl ratio) and mean flow structures prior to injection agree well with the measurements. Modification of the mean flow by fuel injection and combustion is also well captured.

The role of automotive electronics in light duty vehicles is continuing to expand rapidly. In this paper an overview of a 1986 Delphi forecast of major trends is presented. Trends discussed include electronics as a fraction of vehicle and component cost and projections of basic vehicle features supported by electronic technology. In addition, basic trends in diagnostics and multiplexing are presented. Several issues in support of automotive electronics are discussed, including the systems approach to vehicle engineering, the importance of developing a proper market strategy, and the continued major role of energy economics. The Delphi forecasting technique and its governing concepts are reviewed as a method to predict the future of automotive technology.

Privacy has been a rising concern. The European Union has established a privacy standard called General Data Protection Regulation (GDPR) in May 2018. Furthermore, the Facebook-Cambridge Analytica data incident made headlines in March 2018. Data collection from vehicles by OEM platforms is increasingly popular and may offer OEMs new business models but it comes with the risk of privacy leakages. Vehicular sensor data shared with third-parties can lead to misuse of the requested data for other purposes than stated/intended. There exists a relevant regulation document introduced by the Alliance of Automobile Manufacturers (“Auto Alliance”), which classifies the vehicular sensors used for data collection as covered and non-sensitive parameters.

Originally written in 1976 and previously revised in 1983, The Maintenance Council (TMC) Recommended Practice RP-404B is intended to enhance the safety of motor carrier employees by providing guidance regarding the purchase and use of access systems on heavy truck and truck tractors. Compliance with the recommended practice is intended to permit anyone entering or exiting a cab to have three limbs in contact with the truck or truck-tractor at arty time. The scope of the recommended practice covers access systems to the cab and rear of cab areas of all types of heavy trucks and truck tractors, in contrast to Bureau of Motor Carrier Safety (BMCS) regulations which applies only to Cab Over Engine (COE) tractors. The Maintenance Council recommended practice also varies from the BMCS requirements in that it remains a design oriented document.

Crash safety researchers have an increased concern regarding the decreased thoracic deflection and the contributing injury causation factors among the elderly population. Sternum fractures are categorized as moderate severity injuries, but can have long term effects depending on the fragility and frailty of the occupant. Current research has provided detail on rib morphology, but very little information on sternum morphology, sternum fracture locations, and mechanisms of injury. The objective of this study is two-fold (1) quantify sternum morphology and (2) document sternum fracture locations using computed tomography (CT) scans and crash data. Thoracic CT scans from the University of Michigan Hospital database were used to measure thoracic depth, manubriosternal joint, sternum thickness and bone density. The sternum fracture locations and descriptions were extracted from 63 International Center for Automotive Medicine (ICAM) crash cases, of which 22 cases had corresponding CT scans.

This paper presents an overview of techniques for measuring friction using bench tests and fired engines. The test methods discussed have been developed to provide efficient, yet realistic, assessments of new component designs, materials, and lubricants for in-cylinder and overall engine applications. A Cameron-Plint Friction and Wear Tester was modified to permit ring-in-piston-groove movement by the test specimen, and used to evaluate a number of cylinder bore coatings for friction and wear performance. In a second study, it was used to evaluate the energy conserving characteristics of several engine lubricant formulations. Results were consistent with engine and vehicle testing, and were correlated with measured fuel economy performance. The Instantaneous IMEP Method for measuring in-cylinder frictional forces was extended to higher engine speeds and to modern, low-friction engine designs.

Using the CDC (SAE J224), a comparison of the NASS data and the UMTRI field accident files (UM series) indicates a similar distribution of offset frontal crashes. Offset frontal damage occurs in 56-61% of crashes, often involving more than one third of the front of the car. Lap-shoulder belted drivers sustain more AIS 2 or greater injuries when there is interior intrusion and occur more often when the offset damage is in front of the driver. However, this may well be due to the severity of the crash. European studies have no uniformity as to offset frontal collision descriptors are difficult to interpret, or to compare one to another.

Since muscles act to translate an electrical impulse from the central nervous system into motion, it is essential to have a suitable mathematical model for muscles and groups of muscles for a virtual soldier environment. This paper presents a methodology in which the muscle contraction is broken down into three distinct physiological processes: calcium release and re-absorption by the sarcoplasmic reticulum, the rate at which calcium binds and unbinds to troponin, and the generation of force due to cross-bridge cycling and the elasticity of the muscle fibers. These processes have been successfully modeled by Ding and Wexler as a system of coupled differential and algebraic equations. These equations give the calcium-time history and the force time history of the muscle. By varying the electrical stimulation rates, the muscles can produce forces of varying magnitude and duration over which the force can be maintained.

In order to develop confidence in numerical models which are used for automotive crash simulations, results are compared with test data. Modeling assumptions are made when constructing a simulation model for a complex system, such as a vehicle. Through a thorough understanding of the modeling assumptions an appropriate set of variables can be selected and adjusted in order to improve correlation with test data. Such a process can lead to better modeling practices when constructing a simulation model. Comparisons between the time history of acceleration responses from test and simulations are the most challenging. Computing accelerations correctly is more difficult compared to computing displacements, velocities, or intrusion levels due to the second order differentiation with time. In this paper a methodology for enabling the update of a simulation model for improved correlation is presented.

Based on a review of existing theoretical and empirical knowledge of the mechanics of pneumatic tires and tire/vehicle systems, a requirement is defined for experimental data relating the shear forces developed at the tire-road interface to the kinematic variables of influence. Test equipment to satisfy this requirement consists of two complementary pieces of apparatus: a laboratory facility which is a modified version of the B. F. Goodrich flat-bed tester, and a mobile device which consists of a three-component (Fx, Fy, Mz) strain-gage dynamometer mounted on a heavy duty highway tractor. The latter provides a capability for testing at speeds up to 70 mph, normal loads up to 2000 lb, tire sideslip angles up to 18 deg, and steady state or programmed variations in longitudinal tire slip from fully locked (100% slip) to 30% overdriven (-30% slip). Representative samples of tire mechanics data obtained using the new equipment are presented and discussed.

A primary goal of large eddy simulation, LES, is to capture in-cylinder cycle-to-cycle variability, CCV. This is a first step to assess the efficacy of 35 consecutive computed motored cycles to capture the kinetic energy in the TCC-III engine. This includes both the intra-cycle production and dissipation as well as the kinetic energy CCV. The approach is to sample and compare the simulated three-dimensional velocity equivalently to the available two-component two-dimensional PIV velocity measurements. The volume-averaged scale-resolved kinetic energy from the LES is sampled in three slabs, which are volumes equal to the two axial and one azimuthal PIV fields-of-view and laser sheet thickness. Prior to the comparison, the effects of sampling a cutting plane versus a slab and slabs of different thicknesses are assessed. The effects of sampling only two components and three discrete planar regions is assessed.

The influence of the bulk in-cylinder flow on the spray evolution, evaporation, fuel-air mixing and subsequent flame propagation has been studied in an optical SIDI engine. Quantitative LIF imaging of equivalence ratios was used to characterize the mixture formation and the influence of the local equivalence ratio at the time of spark on the flame propagation. Two extreme bulk flow conditions - high and low swirl - were investigated and pronounced differences in mixture homogeneity and flame propagation were found and characterized.

At the forefront of intelligent vehicle technologies are vehicle-to-vehicle communication (V2V) and vehicle-infrastructure integration (VII). Their capabilities can be added to currently-available systems, such as adaptive cruise control (ACC), to drastically decrease the number and severity of collisions, to ease traffic flow, and to consequently improve fuel efficiency and environmental friendliness. There has been extensive government, industry, and academic involvement in developing these technologies. This paper explores the capabilities and challenges of vehicle-based technology and examines ways that policymakers can foster implementation at the federal, state, and local levels.

For human motion studies, which are to be used for either dynamic biomechanical analyses or development of human motion simulation models, it is important to establish an empirical motion database derived from efficient measurement and well-standardized data processing methodologies. This paper describes the motion recording and data processing system developed for modeling seated reach motions at the University of Michigan's HUMOSIM Laboratory. Both electromagnetic (Flock of Birds) and optical (Qualysis) motion capture systems are being used simultaneously to record the motion data. Using both types of devices provides a robust means to record human motion, but each has different limitations and advantages. The amount of kinematic information (DOFs), external sources of noise, shadowing, off-line marker identification/tracking time, and setup cost are key differences.

This paper examines truck driver injury and loss of life in truck crashes related to cab crashworthiness. The paper provides analysis of truck driver fatality and injury in crashes to provide a better understanding of how injury occurs and industry initiatives focused on reducing the number of truck occupant fatalities and the severity of injuries. The commercial vehicle focus is on truck-tractors and single unit trucks in the Class 7 and 8 weight range. The analysis used UMTRI's Trucks Involved in Fatal Accidents (TIFA) survey file and NHTSA's General Estimates System (GES) file for categorical analysis and the Large Truck Crash Causation Study (LTCCS) for a supplemental clinical review of cab performance in frontal and rollover crash types. The paper includes analysis of crashes producing truck driver fatalities or injuries, a review of regulatory development and industry safety initiatives including barriers to implementation.

There is a strong evidence that the overrepresentation of teen drivers in motor vehicle crashes is mainly due to their poor hazard perception skills, i.e., they are unskilled at appropriately detecting and responding to roadway hazards. This study evaluates two cuing systems designed to help teens better understand their driving environment. Both systems use directional color-coding to represent different levels of proximity between one’s vehicle and outside agents. The first system provides an overview of the location of adjacent objects in a head-up display in front of the driver and relies on drivers’ focal vision (focal cuing system). The second system presents similar information, but in the drivers’ peripheral vision, by using ambient lights (peripheral cuing system). Both systems were retrofitted into a test vehicle (2014 Toyota Camry). A within-subject experiment was conducted at the University of Michigan Mcity test-track facility.

A comprehensive model for sprays emerging from high-pressure swirl injectors in DISI engines has been developed accounting for both primary and secondary atomization. The model considers the transient behavior of the pre-spray and the steady-state behavior of the main spray. The pre-spray modeling is based on an empirical solid cone approach with varying cone angle. The main spray modeling is based on the Liquid Instability Sheet Atomization (LISA) approach, which is extended here to include the effects of swirl. Mie Scattering, LIF, PIV and Laser Droplet Size Analyzer techniques have been used to produce a set of experimental data for model validation. Both qualitative comparisons of the evolution of the spray structure, as well as quantitative comparisons of spray tip penetration and droplet sizes have been made. It is concluded that the model compares favorably with data under atmospheric conditions.