Search Results

Dynamic modelling of the contact between the tires of automobiles and the road surface is crucial for accurate and effective vehicle dynamic simulation and the development of various driving controllers. Furthermore, an accurate prediction of the rolling resistance is needed for powertrain controllers and controllers designed to reduce fuel consumption and engine emissions. Existing models of tires include physics-based analytical models, finite element based models, black box models, and data driven empirical models. The main issue with these approaches is that none of these models offer the balance between accuracy of simulation and computational cost that is required for the model-based development cycle. To address this issue, we present a volumetric approach to model the forces/moments between the tire and the road for vehicle dynamic simulations.

The present work is aimed at investigating the tribological factors influencing the LDH test. The material used was AKDQ cold-rolled bare steel, 0.82mm thick. The investigated factors included: test speed (0.833, 4.167, 6.667, and 8.333 mm/s), lubricant viscosity (4.5, 7.0, and 12.5 mm2/s), punch roughness (0.033 and 0.144 μm Ra), and test temperature (25 and 50 °C). Test speed and lubricant viscosity form a variation of the numerator of the Stribeck curve's x-axis (ηV). With ηV increasing from 4 to 120 mm3/s2 friction decreased, resulting in a 0.5 mm higher LDH. Increasing the punch roughness decreased friction producing an increase of 0.25 mm in the LDH. There appears to be an optimum roughness -- at which the roughness features act as lubricant reservoirs but the asperities do not break through the lubricant film -- resulting in minimum friction, therefore, maximum LDH.

Details of the development of metal transfer and friction were studied by drawing cold-rolled bare, galvannealed, electrogalvanized, and hot-dip galvanized strips with a mineral-oil lubricant of 30 cSt viscosity at 40 C, over a total distance of 2500 mm by three methods. An initial high friction peak was associated with metal transfer to the beads and was largest with pure zinc and smallest with Fe-Zn coatings. Insertion of a new strip disturbed the coating and led to the development of secondary peaks. Long-term trends were governed by the stability of the coating. Stearic acid added to mineral oil delayed stabilization of the coating and increased contact area and thus friction with pure zinc surfaces. The usual practice of reporting average friction values can hide valuable information on lubrication mechanisms and metal transfer.

Lithium-ion batteries (LIBs) are one of the best candidates as energy storage systems for automobile applications due to their high power and energy densities. However, durability in comparison to other battery chemistries continues to be a key factor in prevention of wide scale adoption by the automotive industry. In order to design more-durable, longer-life, batteries, reliable and predictive battery models are required. In this paper, an effective model for simulating full-size LIBs is employed that can predict the operating voltage of the cell and the distribution of variables such as electrochemical current generation and battery state of charge (SOC). This predictive ability is used to examine the effect of parameters such as current collector thickness and tab location for the purpose of reducing non-uniform voltage and current distribution in the cell. It is identified that reducing the non-uniformities can reduce the ageing effects and increase the battery durability.

The performance, life cycle cost, and safety of electric and hybrid electric vehicles (EVs and HEVs) depend strongly on their energy storage system. Advanced batteries such as lithium-ion (Li-ion) polymer batteries are quite viable options for storing energy in EVs and HEVs. In addition, thermal management is essential for achieving the desired performance and life cycle from a particular battery. Therefore, to design a thermal management system, a designer must study the thermal characteristics of batteries. The thermal characteristics that are needed include the surface temperature distribution, heat flux, and the heat generation from batteries under various charge/discharge profiles. Therefore, in the first part of the research, surface temperature distribution from a lithium-ion pouch cell (20Ah capacity) is studied under different discharge rates of 1C, 2C, 3C, and 4C.

In electrified vehicle applications, the heat generated of lithium-ion (Li-ion) cells may significantly affect the vehicle range and state of health (SOH) of the pack. Therefore, a major design task is creation of a battery thermal management system with suitable control and cooling strategies. To this end, the thermal behavior of Li-ion cells at various temperatures and operating conditions should be quantified. In this paper, two different commercial pouch cells for plug-in hybrid electric vehicles (PHEVs) are studied through comprehensive thermal performance tests. This study employs a fractional factorial design of experiments to reduce the number of tests required to characterize the behavior of fresh cells while minimizing the effects of ageing. At each test point, the effects of ambient temperature and charge/discharge rate on several types of cell efficiencies and surface heat generation are evaluated.

A series plug-in hybrid electric powertrain with all-wheel drive is designed using real-world drive cycles as part of the EcoCAR 2 competition. A stock 2013 Chevrolet Malibu Eco is being re-engineered to reduce fuel consumption and emissions while improving consumer acceptability. Waterloo utilizes a 18.9 kWh A123 energy storage system (ESS), which powers two 105 kW TM4 traction motors. A 2.4 L LE9 General Motors coupled to a 105 kW TM4 motor provides range extending performance. Each step of the design process is discussed, including a novel approach to powertrain selection and controls requirement selection that uses real-world drive cycles. The mechanical integration and unique ESS design is also discussed.

The objective of this paper is to help students optimize project component selection or design by detailing, through two specific examples, the University of Waterloo's Alternative Fuels Team's (UWAFT's) successful design process. UWAFT successfully designed a fuel cell powered vehicle for the ChallengeX student engineering competition. The use of a formal, structured design process enabled this team to achieve great confidence in both the feasibility of their design and their ability to manifest the design. This design process is model-based whereby a parameterized software model is created. This paper hopefully assists students to overcome a common reluctance to implementing a model-based design process. After a component is constructed and tested, students can update their software model, which can help them assess the strength of their design.

The present paper offers a status report on round-robin tests conducted with the participation of ten laboratories, with drawbead simulation (DBS) as the test method. The results showed that, in most laboratories, the coefficient of friction (COF) derived from the test is repeatable within an acceptable range of ±0.01. Repeatability between laboratories was less satisfactory. Five laboratories reported results within the desirable band, while some laboratories found consistently higher values. In one instance this could be traced to incomplete transfer of clamp forces to the load cell, in other instances inaccurate test geometry is suspected. Therefore, numerical values of COF from different laboratories are not necessarily comparable. Irrespective of these inter-laboratory variations, the relative ranking of lubricants was not affected, and data generated within one laboratory can be used for relative evaluations and for a resolution of production problems.

This paper seeks to identify the refrigeration load of a hybrid electric truck in order to find the demand power required by the energy management system. To meet this objective, in addition to the power consumption of the refrigerator, the vehicle mass needs to be estimated. The Recursive Least Squares (RLS) method with forgetting factors is applied for this estimation. As an example of the application of this parameter identification, the estimated parameters are fed to the energy control strategy of a parallel hybrid truck. The control system calculates the demand power at each instant based on estimated parameters. Then, it decides how much power should be provided by available energy sources to minimize the total energy consumption. The simulation results show that the parameter identification can estimate the vehicle mass and refrigeration load very well which is led to have fairly accurate power demand prediction.

The analysis of nickel metal hydride (Ni-MH) battery performance is very important for automotive researchers and manufacturers. The performance of a battery can be described as a direct consequence of various chemical and physical phenomena taking place inside the container. In this paper, a physics-based model of a Ni-MH battery will be presented. To analyze its performance, the efficiency of the battery is chosen as the performance measure, which is defined as the ratio of the energy output from the battery and the energy input to the battery while charging. Parametric sensitivity analysis will be used to generate sensitivity information for the state variables of the model. The generated information will be used to showcase how sensitivity information can be used to identify unique model behavior and how it can be used to optimize the capacity of the battery. The results will be validated using a finite difference formulation.

Battery packs of electric vehicles are typically composed of lithium-ion batteries with aluminum and copper acting as cell terminals. These terminals are joined together in series by means of connector tabs to produce sufficient power and energy output. Such critical electrical and structural cell terminal connections involve several challenges when joining thin, highly reflective and dissimilar materials with widely differing thermo-mechanical properties. This may involve potential deformation during the joining process and the formation of brittle intermetallic compounds that reduce conductivity and deteriorate mechanical properties. Among various joining techniques, laser welding has demonstrated significant advantages, including the capability to produce joints with low electrical contact resistance and high mechanical strength, along with high precision required for delicate materials like aluminum and copper.

Modern electrified vehicles rely on drivers to manually adjust control parameters to modify the vehicle's powertrain, such as regenerative braking strength selection or drive mode selection. However, this reliance on infrequent driver input may lead to a mismatch between the selected powertrain control modifiers and the true driving environment. It is therefore advantageous for an electric vehicle's powertrain controller to make online identifications of the current driving conditions. This paper proposes an online driving condition identification scheme that labels drive cycle intervals collected in real-time based on a clustering model, with the objective of informing adaptive powertrain control strategies. HDBSCAN and K-means clustering models are fitted to a data set of drive cycle intervals representing a full range of characteristic driving conditions.

The autoignition delay of a turbulent methane jet in a Diesel-like environment is calculated by the conditional moment closure(CMC) model. Methane is injected into hot air in a constant volume chamber under various temperatures and pressures. Detailed chemical reaction mechanisms are implemented with turbulence-chemistry interaction treated by the first order CMC. The CMC model solves the conditional mean species mass fraction and temperature equations with the source term given in terms of the conditional mean quantities. The flow and mixing field are calculated by the transient SIMPLE algorithm with the k -ε model and the assumed beta function pdf. The CMC equations are solved by the fractional step method which sequentially treats the transport and chemical reaction terms in each time step. The predictions in quiescent homogeneous mixture are presented to evaluate the effects of turbulence in jet ignition.

Vehicle weight reduction through the use of components made of magnesium alloys is an effective way to reduce carbon dioxide emission and improve fuel economy. In the design of these components, which are mostly under cyclic loading, notches are inevitably present. In this study, surface strain distribution and crack initiation sites in the notch region of AZ31B-H24 magnesium alloy notched specimens under uniaxial load are measured via digital image correlation. Predicted strains from finite element analysis using Abaqus and LS-DYNA material types 124 and 233 are then compared against the experimental measurements during quasi-static and cyclic loading. It is concluded that MAT_233, when calibrated using cyclic tensile and compressive stress-strain curves, is capable of predicting strain at the notch root. Finally, employing Smith-Watson-Topper model together with MAT_233 results, fatigue lives of the notched specimens are estimated and compared with experimental results.

Direct injected natural gas diesel engines are currently being developed. Numerical analyses results are presented for 20.0 MPa (≈ 3000 psia; 200 atm), 444 K, natural gas injection into 4.0 MPa cylinder air where the ambient turbulence field is representative of diesel engines. Two very important non-intuitive, observations are made. First, the seemingly reasonable spatially uniform velocity profile currently used at the injector exit is not appropriate, rather a double-hump profile is correct. Second, a spatially uniform, injector exit, temperature profile results in local temperature overestimates as large as 300 K. Considering the strong role of temperature on chemical kinetics, this second observation may have profound implications on the validity of conclusions reached using uniform exit profiles.

In this paper, initial results of Li-ion battery performance characterization through field tests are presented. A fully electrified Ford Escape that is equipped by three Li-ion battery packs (LiFeMnPO4) including an overall 20 modules in series is employed. The vehicle is in daily operation and data of driving including the powertrain and drive cycles as well as the charging data are being transferred through CAN bus to a data logger installed in the vehicle. A model of the vehicle is developed in the Powertrain System Analysis Toolkit (PSAT) software based on the available technical specification of the vehicle components. In this model, a simple resistive element in series with a voltage source represents the battery. Battery open circuit voltage (OCV) and internal resistance in charge and discharge mode are estimated as a function of the state of charge (SOC) from the collected test data.

Lithium-ion batteries, which are nowadays common in laptops, cell phones, toys, and other portable electronic devices, are also viewed as a most promising advanced technology for electric and hybrid electric vehicles (EVs and HEVs), but battery manufacturers and automakers must understand the performance of these batteries when they are scaled up to the large sizes needed for the propulsion of the vehicle. In addition, accurate thermo-physical property input is crucial to thermal modeling. Therefore, a designer must study the thermal characteristics of batteries for improvement in the design of a thermal management system and also for thermal modeling. This work presents a purely experimental thermal characterization in terms of measurement of the temperature gradient and temperature response of a lithium-ion battery utilizing a promising electrode material, LiFePO4, in a prismatic pouch configuration.

Hybrid electric vehicles (HEVs) are considered as the most commercial prospects new energy vehicles. Most HEVs have adopted Atkinson cycle engine as the main drive power. Atkinson cycle engine uses late intake valve closing (LIVC) to reduce pumping losses and compression work in part load operation. It can transform more heat energy to mechanical energy, improve engine thermal efficiency and decrease fuel consumption. In this paper, the investigations of Atkinson cycle converted from conventional Otto cycle gasoline engine have been carried out. First of all, high geometry compression ratio (CR) has been optimized through piston redesign from 10.5 to 13 in order to overcome the intrinsic drawback of Atkinson cycle in that combustion performance deteriorates due to the decline in the effective CR. Then, both intake and exhaust cam profile have been redesigned to meet the requirements of Atkinson cycle engine.

A compact sized vehicle that has a narrow track could solve problems caused by vehicle congestion and limited parking spaces in a mega city. Having a smaller footprint reduces the vehicle's total weight which would decrease overall vehicle power consumption. Also a smaller and narrower vehicle could travel easily through tight and congested roads that would speed up the traffic flow and hence decrease the overall traffic volume in urban areas. As an additional benefit of having a narrow track length, a driver can experience similar motorcycle riding experience without worrying about bad weather conditions since a driver sits in a weather protected cabin. However, reducing the vehicle's track causes instability in vehicle dynamics, which leads to higher possibility of rollovers if the vehicle is not controlled properly. A three wheel personal vehicle with an active tilting system is designed in MapleSim.