Search Results

Sliding wear of magnesium (Mg) engine cylinder bore surfaces and corrosion of Mg engine coolant channels are the two unsolved critical issues that automakers have to deal with in development of magnesium-intensive engines. In this paper, Plasma Electrolytic Oxidation (PEO) process was used to produce oxide coatings on AJ62 Mg alloy to provide wear and corrosion protection. In order to optimize the PEO process, orthogonal experiments were conducted to investigate the effect of PEO process parameters on the wear properties of PEO coatings. The PEO coatings showed a much better wear resistance, as well as a smaller friction coefficient, than the AJ62 substrate. The galvanic corrosion property of AJ62 Mg coupled with stainless steel and aluminum (Al) was investigated via immersion corrosion test in an engine coolant. Applying PEO coating on Mg can effectively prevent the galvanic corrosion attack to Mg.

This study provides an overview of a novel method for evaluating in-vehicle speech intelligibility using the Speech Intelligibility Index (SII). The approach presented is based on a measured speech signal evaluated at the sentence Speech Reception Threshold (sSRT) in a simulated driving environment. In this context, the impact of different band importance functions in the evaluation of the SII using the Hearing in Noise Test (HINT) in a driving simulator is investigated.

In order to reduce the weight of an automotive engine, an aluminum (Al) alloy engine block with cast iron liner has been successfully used to replace the gray cast iron engine. For newly emerging Al linerless engine in which the low surface hardness of the aluminum alloy has to be overcome, a few surface processing technologies are used to protect the surface of cylinders. Among them, plasma transferred wire arc (PTWA) thermal spraying coating is becoming popular. Plasma electrolytic oxidation (PEO) coating is also proposed for increasing the wear resistance of aluminum alloy and reducing the friction between the cylinder and piston. In this work, a PEO coating with a thickness of ∼20 μm was prepared, and a high speed pin-on-disc tribometer was used to study the tribological behavior of the coating at oil lubricant conditions. Different surface roughness of the coating and a large range of the sliding speeds were employed for the tests.

A number of cylinder-pressure derived parameters including the crank angles of maximum pressure, maximum rate of pressure rise, and 50% heat released are considered as among the desired feedback for cycle-by-cycle adaptive control of diesel combustion. For real-time computation of these parameters, the heat release analyses based on the first law of thermodynamics are used. This paper intends to identify the operating regions where the simplified heat release approach provides sufficient accuracy for control applications and also highlights those regions where its use can lead to significant errors in the calculated parameters. The effects of the cylinder charge-to-wall heat transfer and the temperature dependence of the specific heat ratio on the model performance are reported. A new computationally efficient algorithm for estimating the crank angle of 50% heat released with adequate accuracy is proposed for computation in real-time.

Diesel engines operating in the low-temperature combustion (LTC) mode generally tend to produce very low levels of NOx and soot. However, the implementation of LTC is challenged by the higher cycle-to-cycle variation with heavy EGR operation and the narrower operating corridors. The robustness and efficiency of LTC operation in diesel engines can be enhanced with improvements in the promptness and accuracy of combustion control. A set of field programmable gate array (FPGA) modules were coded and interlaced to suffice on-the-fly combustion event modulations. The cylinder pressure traces were analyzed to update the heat release rate concurrently as the combustion process proceeds prior to completing an engine cycle. Engine dynamometer tests demonstrated that such prompt heat release analysis was effective to optimize the LTC and the split combustion events for better fuel efficiency and exhaust emissions.

Due to considerable efforts of automobile manufacturers to attenuate various noise sources within the passenger compartment, other sources, including induction noise have become more noticeable. The present study investigates the feasibility of using a non-conventional noise cancellation technique to improve the acoustic performance of an automotive induction system by using acoustic energy derived from the exhaust manifold as the dynamic noise source to cancel intake noise. The validity of this technique was first investigated analytically using a computational engine simulation software program. Using these results, a physical model of the bridge was installed and tested on a motored engine. The realized attenuation of the intake noise was evaluated using conventional FFT analysis techniques as well as psychoacoustic metrics including loudness, sharpness, roughness and fluctuation strength.

Friction between the piston and cylinder accounts for large amount of the friction losses in an internal combustion (IC) engine. Therefore, any effort to minimize such a friction will also result in higher efficiency, lower fuel consumption and reduced emissions. Plasma electrolytic oxidation (PEO) coating is considered as a hard ceramic coating which can provide a dimpled surface for oil retention to bear the wear and reduce the friction from sliding piston rings. In this work, a high speed pin-on-disc tribometer was used to generate the boundary, mixed and hydrodynamic lubrication regimes. Five different lubricating oils and two different loads were applied to do the tribotests and the COFs of a PEO coating were studied. The results show that the PEO coating indeed had a lower COF in a lower viscosity lubricating oil, and a smaller load was beneficial to form the mixed and hydrodynamic lubricating regimes earlier.

Individuals with hearing impairments often report hearing difficulties within the driving environment. This is an ever growing issue given the increasing population of senior aged drivers. In this study, Speech Intelligibility Index (SII) is used to predict in-vehicle speech intelligibility of individuals having common hearing impairments. The effect of hearing threshold levels obtained from audiograms and the impact of vehicle background noise measured for various vehicle operating conditions, road surface types and talker and listener configurations are investigated. This is done by using measured and user-defined speech spectra as described by ANSI S3.5-1997 (Methods for Calculation of the Speech Intelligibility Index). The results demonstrate poor speech intelligibility for most situations considered and provide evidence for the need to improve automotive interior sound quality in terms of speech intelligibility for hearing impaired drivers including aged drivers.

Highly accurate cylinder pressure data can be acquired using a wall-mounted and water-cooled quartz piezoelectric transducer. However, this type of transducer does not satisfy the cost and packaging constraints when used in a production engine application. A potential solution to these issues that has been the interest of many is the much smaller and less expensive optical fiber based pressure transducer. This research compares Kistler piezoelectric transducers to Optrand optical fiber transducers. The influence of the transducer type and mounting arrangement on the quality of cylinder pressure data was examined. The transducers were evaluated on a DaimlerChrysler 4.7L V-8 Compressed Natural Gas fuelled test engine. The analysis method is comprised of examining measured individual cycle and ensemble-averaged cylinder pressure records to assess the quality of the data and its usefulness for engine management.

A Split-Cycle engine fueled with methane has been constructed and operated at the University of Windsor. A split-cycle engine consists of two interconnected cylinders working together to preform the four engine strokes. Cylinder 1 preforms intake and compression strokes while cylinder 2 is where combustion, expansion and exhaust occur. The connecting high pressure crossover passage is where methane is injected, resulting in a well pre-mixed air-fuel mixture. Transfer occurs to the combustion cylinder near TDC, resulting in intense small scale turbulence that leads to short combustion durations under 30° CA. Short durations are achieved despite low engine speeds of 850-1200 rpm, late combustion phasing and part loads. Of note is the lean limit of operation of the engine at the equivalence ratio Φ = 0.85, which is high compared to other natural gas engines which have limits around Φ = 0.6.

In order to improve the fuel economy for future high-efficiency spark ignition engines, the use of advanced combustion strategies with an overall lean and/or exhaust gas recirculation diluted cylinder charge is deemed to be beneficial, provided a reliable ignition process available. In this paper, experimental results of igniting methane-air mixture by means of capacitive coupled ignition and multi-coil distributed spark ignition are presented. It is found that with a conventional spark plug electrode configuration, increase of spark energy does not proportionally enhance the ignition flame kernel development. The use of capacitive coupled ignition to enhance the initial transient power resulted in faster kernel growth compared to the conventional system. The distribution of the spark energy across a number of spark gaps shows considerable benefit.

Heat-release and cylinder pressure based adaptive fuel-injection control tests were performed on a modern common-rail diesel engine to improve the engine operation in the low-temperature combustion (LTC) region. A single shot injection strategy with heavy amount of exhaust gas recirculation (EGR) was used to modulate the in-cylinder charge conditions to achieve the low-temperature combustion. Adaptive fuel-injection techniques were used to anchor the cylinder pressure characteristics in the desired crank angle window and thereby stabilize the engine operation. The response of the adaptive control to boost, fueling, and engine speed variations was also tested. A combination of adaptive fuel-injection and automatic boost/back-pressure controls had helped to make the transient emissions comparable to the steady-state LTC emissions.

Three different pairs of high melting temperature and low melting temperature nylons have been welded together using three different design of experiment welding process parameter matrices. An unorthodox analysis of these has revealed that there is a general increase in strength as the total welding sliding distance of the two surfaces increases. This is not surprising. The analysis also reveals that, for a given sliding distance, the vibration amplitude should be large, which shortens the welding time. This strategy produces shorter cycle times and stronger welds, according to the data obtained in these test sets.

Advanced engine test methods incorporate several different sensing and signal processing techniques for identifying and locating manufacturing or assembly defects of an engine. A successful engine test method therefore, requires advanced signal processing techniques. This paper introduces a novel signal processing technique to successfully detect a faulty internal combustion engine in a quantitative manner. Accelerometers are mounted on the cylinder head and lug surfaces while vibration signals are recorded during engine operation. Using the engine's cam angular position, the vibration signals are transformed from the time domain to the crank-angle domain. At the heart of the transformation lies interpolation. In this paper, linear, cubic spline and sinc interpolation methods are demonstrated for reconstructing vibration signals in the crank-angle domain.

Aluminum engines have been successfully used to replace heavy gray cast engines to lighten the car's weight and reduce the fuel consumption. To overcome the aluminum alloys' poor wear resistance, cast iron liners and thermal spraying coatings were used as cylinder bore materials for wear protection. A plasma electrolytic oxidation (PEO) technique had also been proposed to produce an oxide coating on aluminum cylinder bore. The oxide coating can have a low coefficient of friction (COF) and minimum wear shown in the lab tests. To conserve more fuel, the stopping and restarting system was introduced when the vehicle was forced to stop immediately for a short time. When the engine was forced to stop and restart, the reciprocating speed of the piston was very slow, and the friction between the piston and the cylinder was high. In this research, a pin-on-disc tribometer was used to investigate tribological behavior of the oxide coating on an aluminum alloy.

The effects of engine noise in plastic manifolds has been a subject of study in the automotive Industry. Several SAE papers have been published on the subject. Most testing described requires access to engine dynamometers and other elaborate equipment. As part of a general study of plastic intake manifold noise characteristics, this study was undertaken to develop a synthesis bench for enabling low cost noise testing of plastic induction systems including plastic manifolds. Computer simulation of engine intake noise was used as part of a correlation between the plastic manifold synthesis bench and actual engine measurements. The Fast Fourier Transform (FFT) analysis provided analogous results between the predicted theoretical and two measured signals with a fundamental frequency at approximately 80 Hz. Qualitative and statistical comparisons of the time domain signals also proved equally favourable. Recommendations are included for further development of this approach.

A production V-8 engine was redesigned to run on low temperature combustion (LTC) with conventional Diesel fuel. Two fuel injection strategies were used to attain reduction in soot and NOx; a) early premixed injection strategy: fuel injected early during the compression stroke and b) late premixed injection strategy: fuel injected close to TDC with heavy EGR. The early premixed injection strategy yielded low NOx and soot but struggled to vaporize the fuel as noted in unburned hydrocarbons readings. The late premixed injection strategy introduced the fuel at higher in-cylinder temperatures and densities, improving the fuel's vaporization and limited the unburned hydrocarbon and carbon monoxide. The use of high EGR and high injection pressure for late premixed injection strategy provided sufficiently long ignition delay that resulted in partially premixed cylinder charge before combustion, and thereby prevented high soot, even in presence of high EGR.

Amid all nondestructive testing (NDT) methods Ultrasound is considered the most practically feasible modality for quality assessment and detection of defects in automobile industry. Pattern recognition of the ultrasonic signals gives us important information about the interrogated object. This information includes size, geometric shape and location of the defect zone. However, this would not be straightforward to extract this information from the backscattered echoes due to the overlapping signals and also the presence of noise. Here in this study, we suggest a new method for classification of different defects in inspection of adhesively bonded joint. At the first step of this method, the problem of parameter estimation of the reflected echoes is defined in a Maximum Likelihood Estimation (MLE) framework. Then a space alternating generalized Expectation Maximization (SAGE) algorithm is implemented to solve the MLE problem.

Hollow polymer-based automotive components cannot, in general, be directly injection molded because they cannot be ejected from the mold. The common practice is to injection mold two or more parts, and then join these together with a welding process. Of the many joining process available, laser welding has an advantage in geometric design freedom. The laser weld joints are also generally stronger than those of vibration welds because the weld joints are located in the walls rather than on external flanges. Eliminating the external flanges also makes the part more compact. In transmission laser welding processes, the laser beam passes through a transparent part to its interface with an opaque part. The beam energy is absorbed near the interface in the opaque part, and heat flows back across to the transparent half to make the weld pool. So successful laser welds are possible only when there is a continuous interfacial fit between the parts.

In this work, engine tests were performed to realize EGR-enabled LTC on a single-cylinder common-rail diesel engine with three different compression ratios (17.5, 15 and 13:1). The engine performance was first investigated at 17.5:1 compression ratio to provide baseline results, against which all further testing was referenced. The intake boost and injection pressure were progressively increased to ascertain the limiting load conditions for the compression ratio. To extend the engine load range, the compression ratio was then lowered and EGR sweep tests were again carried out. The strength and homogeneity of the cylinder charge were enhanced by using intake boost up to 3 bar absolute and injection pressure up to 180 MPa. The combustion phasing was locked in a narrow crank angle window (5~10° ATDC), during all the tests.