Search Results

Battery electric vehicles (BEVs) are equipped with Mobile Air Conditioning systems (MACs) to ensure a comfortable cabin temperature in all climates and ambient conditions as well as the optional conditioning of the traction battery. An assessment of the global electrical energy consumption of various MACs has been derived, where the basis of the assessment procedure is the climate data GREEN-MAC-LCCP 2007 (Global Refrigerants Energy & Environmental - Mobile Air Condition - Life Cycle Climate Performance) and the improved LCCP2013 (Life Cycle Climate Performance. The percentage driving time during 6 AM and 24 PM is divided into six different temperature bins with the solar radiation and relative humidity for 211 cities distributed over Europe, North, Central, and South America, Asia, South West Pacific, and Africa. The energy consumption of the MACs is determined by a thermal vehicle simulation. In this work, four different MACs are simulated and compared.

The hatchback of Volkswagen's 3 liter car (3 l fuel consumption per 100 km) consists of an inner component of die casting magnesium (AM50) covered with an aluminum panel from the outside. This hybrid design requires a new manufacturing process: The pre-coated magnesium part will be bonded and folded with the bare aluminum part. Corrosion protection is provided by an organic coating system which both protects against general corrosion and galvanic corrosion. The corrosion of the Al / Mg sandwich has been examined with hybrid samples which are similar to the hatchback. Several powder coatings (epoxy resin, polyester resin, hybrid resin), wet paints and cathodic electro-coating paints of different thicknesses and compositions have been applied to the magnesium part. They show that only powder coating provides adequate protection. Galvanic corrosion at the points of attachment of the hatchback might be possible (for example the bolted joint of the hinge).

Strategic Materials at Reaction Temperatures (SMART) is an approach used to design washcoat systems for passive 4-way emission control catalysts. Light duty diesel vehicles need to meet the European Motor Vehicle Emissions Group (MVEG) cycle or U. S. Federal test procedure (FTP 75). Emissions that are monitored include hydrocarbon (HC), nitrogen oxides (NOx), carbon monoxide (CO) and total particulate matter (TPM). Low engine-exhaust temperatures (< 200°C during city driving) and high temperatures (> 500-800°C under full load and wide-open throttle) make emission control a formidable task for the catalyst designer Gas phase HC, CO and NOx reactions must be balanced with the removal of the soluble organic fraction for the vehicle to be in compliance with regulations. The SMART approach uses model gases under typical operating conditions in the laboratory to better understand the function of individual washcoat components.

In a consortium of European industrial partners and research institutes, a combination of industrial development and scientific research was organised. The objective was to improve the catalytic NOx conversion for lean burn cars and heavy-duty trucks, taking into account boundary conditions for the fuel consumption. The project lasted for three years. During this period parallel research was conducted in research areas ranging from basic research based on a theoretical approach to full scale emission system development. NOx storage catalysts became a central part of the project. Catalysts were evaluated with respect to resistance towards sulphur poisoning. It was concluded that very low sulphur fuel is a necessity for efficient use of NOx trap technology. Additionally, attempts were made to develop methods for reactivating poisoned catalysts. Methods for short distance mixing were developed for the addition of reducing agent.

Compatibility has been a passive safety research issue for many years. Great advancements in secondary (passive) safety have been achieved in the last decades through focussing on the self-protection level provided by passenger cars. The next step is to consider the other vehicle involved in the collision as well. Compatibility relates to the simultaneous improvement of both self- and partner- protection. Several tests procedures have been proposed around the world to assess the compatibility of passenger cars. None are considered ready to be implemented. This paper shows that controlling vehicle front-end geometry is the most feasible step to improve both self- and partner-protection. Through this, an increase in the structural interaction potential offered by passenger cars would result. To improve structural interaction, a convergence of front-end structures, to within certain vertical limits, is necessary.

This paper describes an investigation of one operating point of the transient warmup curve of a gasoline engine. Coolant liquid and oil of this engine have been cooled down to a constant low level in order to perform detailed measurements and an analysis of this particular warmup point. The influence of low coolant temperature, different pressure drop in an air assisted fuel injection system and a variation of ignition angles on specific fuel consumption, exhaust emissions, energy conversion etc. will be shown. The results show that the suggested test procedure (keeping the coolant temperature at a constant low level) provides the possibility to simulate the behaviour of an engine with air assisted fuel injection during warmup. During this warmup period it is desired to run the engine with retarded ignition timing to realize a fast catalyst warmup.

Electric power steering systems (EPS) are characterized by high inertia and therefore by a considerably damped transmission behaviour. While this is desirable for comfort-oriented designs, EPS do not provide enough feedback of the driving conditions, especially for drivers with a sporty driving style. The systematic actuation of the electric motor of an EPS makes it possible to specifically increment the intensity of the response. In this context, the road-sided induced forces of the tie rod and the steering rack force provide all the information for the steering system’s response. Former concepts differentiate between use and disturbance information by defining frequency ranges. Since these ranges overlap strongly, this differentiation does not segment distinctively. The presented article describes a method to identify useful information in the feedback path of the steering system depending on the driving situation.

Dry dust testing of vehicles on unpaved dust roads plays a crucial role in the development process of automotive manufacturers. One of the central aspects of the test procedure is ensuring the functionality of locking systems in the case of dust ingress and keeping the dust below a certain concentration level inside the vehicle. Another aspect is the customer comfort because of dust deposited on the surface of the car body. This also poses a safety risk to customers when the dust settles on safety-critical parts such as windshields and obstructs the driver’s view. Dust deposition on sensors is also safety critical and is becoming more important because of the increasing amount of sensors for autonomous driving. Nowadays, dust tests are conducted experimentally at dust proving grounds. To gain early insights and avoid costly physical testing, numerical simulations are considered a promising approach. Simulations of vehicle contamination by dry dust have been studied in the past.

Dust testing of vehicles on unpaved roads is crucial in the development process for automotive manufacturers. These tests aim to ensure the functionality of locking systems in dusty conditions, minimize dust concentration inside the vehicle, and enhance customer comfort by preventing dust accumulation on the car body. Additionally, deposition on safety-critical parts, such as windshields and sensors, can pose threats to driver vision and autonomous driving capabilities. Currently, dust tests are primarily conducted experimentally at proving grounds. In order to gain early insights and reduce the need for costly physical tests, numerical simulations are becoming a promising alternative. Although simulations of vehicle contamination by dry dust have been studied in the past, they have often lacked detailed models for tire dust resuspension. In addition, few publications address the specifics of dust deposition on vehicles, especially in areas such as door gaps and locks.

To date, no generally valid statements can be made about the service life of brake pads, which may be due to factors such as driving style, the friction material used or the varying vehicle weight. While dynamic friction models including friction history are already established [1], the investigation of wear and wear dust behavior is currently in the focus of many research projects. One example is the investigation of calculation models for brake pad wear while neglecting the temperature development in the brake [2]. In cars, temperatures of up to 800°C occur in the brake under high loads, which leads to a significant increase in wear. Accordingly, the question arises how an estimation of brake pad wear can be applied to highly dynamic load cases. To do this, however, the processes taking place in the boundary layer between pad and disc must first be comprehensively understood and described.

Compatibility has been a research issue for many years now. It has gained more importance recently due to significant improvements in primary and secondary safety. Using a rigorous approach, combining accident research and theoretical scientific considerations, measures to improve vehicle-vehicle compatibility, with an emphasis on feasibility, were discussed. German accident research statistics showed that frontal impacts are of higher statistical significance than side impacts. Based on this and the high potential for improvement due high available deformation energy, the frontal impact configuration was identified as the most appropriate collision mode for addressing the compatibility issue. In side impacts, accident avoidance was identified as the most feasible and sensible measure. For frontal vehicle-vehicle impacts, both trucks and passenger cars were identified as opponents of high statistical significance.

The growing demand for the use of magnesium alloys in the production of automotive powertrain components led to the development of creep resistant diecasting alloys MRI153M and MRI230D. The present paper addresses the main high-pressure die casting parameters, which significantly affect the performance of components, produced of these new alloys. A systematic study was carried out in order to correlate die-casting parameters to the performance of new alloys. The results obtained clearly indicated that optimization of molten metal and die temperatures, injection profile parameters and lubrication mixtures allowed to improve the die castability and service properties of the new alloys and produce high performance components with intricate geometry. This was manifested by production of several practical demonstrators such as gearboxes, oil pans, oil pumps and crankcases.

A new method has been designed to examine car seats by technical means only, whether they fit summer conditions or not. Test procedures start with the application of a carefully wetted cloth onto the seat to be examined. The test area is then covered by a temperature controlled, electrically heated solid body bloc. This simulates the body temperature and the seat pressure of a real seat user. During test periods of standard three hours, temperature and humidity is measured beneath the test device and in the surrounding air. As an effect of the water impulse the humidity increases under the body bloc. It has been proved that good summer suitability of a car seat is characterised by moderate amount and moderate duration of increased humidity readings. Poor suitability results in higher amount and longer duration of raised humidity. The method is shown to be useful to examine full scale car seats, child safety seats and single design characteristics of car seats as well.